• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.5
• /
• pp.441-451
• /
• 2016

This study analyzed behavior of the segment lining considering connection type between inner-slab and segment lining for a double deck tunnel by Shield TBM. In order to establish the design requirements of inner-slab and segment lining in double deck tunnel, inner structure of double deck tunnel at each purpose was analyzed and compared connection type between inner-slab and segment lining. And analyses have been carried out through the beam-spring model by MIDAS Civil 2012. As a result of this study, inner-slab, connection type of between inner-slab and segment lining and Lateral earth pressure coefficients were analyzed to verify the significant design factors.

• Journal of Wind Energy
• /
• v.13 no.3
• /
• pp.22-32
• /
• 2022

Conventionally, a monopile that has reached the end of its design life is required to be removed. While monopiles have been left on site due to economic and technical reasons, cases of decommissioning monopoles have recently been reported, and a decommissioning market is emerging. This paper introduces a new type of monopile with decreased pull-out resistance by prior lifting up of a wedge segment installed on the outer wall of the monopile; consequently, the monopile can be dismantled easily from the operation site. The study conducted several numerical investigations, using finite element analysis, of the effect of segment pull-out for the monopile. After pulling out several segment sizes in the numerical model represented by soil element deletion corresponding to the segment volumes, the pull-out forces were compared to those of the conventional monopile. The results showed that for a segment with a thickness of 5 cm and circumferential angle of 30°, the pull-out resistance of the proposed monopile was reduced by 32.5% relative to that of a conventional monopile. Also, the results indicated that an increase in the segment angle was a more effective way to reduce resistance than that of the thickness.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.3
• /
• pp.235-240
• /
• 2014

A novel segment type switched reluctance motor (SRM) as a rare-earth-less motor is proposed. The torque was increased by 40% and the radial force was decreased by 76% compared with the same size usual variable reluctance (VR) type SRM. Increasing the average torque, however, caused increasing torque ripple. In this paper we develop a 4-phase segment type SRM and show that the torque ripple can be decreased well.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.17 no.4
• /
• pp.608-621
• /
• 1993

The Purposes of this study were 1)to find the body surface total line and segment line significantly(${\alpha}$=0.05) changed by the leg movement including all movement direction of hip joint, knee joint and ankle joint for the more functional clothing. 2)to classify them into 3 types-expansion type, contraction type, expansion & contraction type, and 3)to identify the characteristics of the body surface length changes. 10 Crosswise and 5 lengthwise body surface total lines and 48 crosswise & 39 lengthwise body surface segment lines of 26 female college students aged from 18 to 24 years were measured directly on the body surface and were analyzed by ANOVA & Multiple Comparison Test (Tukey). The results were as following : Body surface total lines significantly changed were all the body surface total lines except abdoman girth, 1/2thigh girth of lower leg and ankle girth, and these were classified into 3 types : Center front leg line belonged to expansion & contraction type, whereas lateral leg line, legscye girth, and total crotch length belonged to contraction type. The rest belonged to expansion type. Knee girth showed maximum expansion, whereas center front leg line showed maximum contraction. Body surface total lines have shown large expansion crosswise whereas lengthwise they have mainly shown contraction. At least more than one component segment line of each body surface total lines except abdoman girth and ankle girth have shown significant change. Top segment of inner leg line showed maximum expansion. whereas just below top segment of center front leg line showed maximum contraction. Crosswise all the body surface segment lines have shown expansion except inner back segments of thigh girth and 1/2thigh girth of upper leg which have shown contraction. Lengthwise they have shown both expansion and contraction according to the location of front or back, and below or upper 1/2thigh girth line except the component segment lines of lateral leg line, which has shown contraction only.(cf. figure 2. figure 3. and table 2-2).

• Journal of Power System Engineering
• /
• v.5 no.3
• /
• pp.64-72
• /
• 2001

This paper describes an optimal design technology in a segment type vertical guide bearing for vertical rotating machinery. Segment type vertical guide bearings have widely used for vertical rotating machinery, however bearing problems, such as excessive vibration and temperature rise, frequently take place in the actual machine. Such excessive vibration magnitude and/or abnormal bearing metal temperature rise result in serious damage and economic losses. Thus the segment type vertical guide bearing should be designed to get optimal characteristics in order to maintain stable operation without bearing failure due to abnormal vibration and/or abnormal bearing metal temperature. The preload ratio is the most important parameter in designing the segment type vertical guide bearing. Because adjustment of the bearing preload by changing the bearing clearance could easily control both the bearing stiffness and the cooling effect. In the paper, the influence of the preload effects on the bearing metal temperature and the bearing stiffness has been investigated both theoretically and experimentally in order to find out an optimum preload ratio. Results show that the segment type vertical guide bearing has an optimum preload ratio at which the bearing stiffness reaches a masimum value while the bearing metal temperature is minimized.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.6
• /
• pp.527-534
• /
• 2018

The segment of the piston type wave board has been expressed as a submerged vertical line segment in the two dimensional wave flume. Either end of vertical line segment representing wave board could be located in fluid domain from free surface to the bottom of the flume. Naturally the segment could be extended from the bottom to the free surface of the flume. It is assumed that the piston motion of the wave board could be defined by the sinusoidal oscillation in horizontal direction. Simplified analytic solution of the submerged segment of wave board has been derived through the first order perturbation method in water of finite depth. The analytic solution has been utilized in expressing the wave generated by the piston type wave board installed on the upper or lower half of the flume. The wave form derived by the analytic solution have been compared with the wave profile obtained through the CFD calculation for the either of the above cases. It is appeared that the wave length and the wave height are coincided each other between analytic solution and CFD calculation. However the wave form obtained by CFD calculations are more closer to real wave form than those from analytic calculation. It is appeared that the linear solutions could be not only superposed by segment but also integrated by finite elements without limitation. Finally it is proven that the wave generated by the oscillation of flap type wave board could be derived by integrating the wave generated by the sinusoidal motion of the finite segment of the piston type wave board.

• Speech Sciences
• /
• v.11 no.4
• /
• pp.207-221
• /
• 2004

There are two different approaches in studying mapping between syntactic structure and prosody, the 'phonetic approach' and the 'phonological approach'. An experiment to examine which approach is more valid was conducted. In the experiment, syntactically ambiguous Seoul Korean sentences in each of which a noun immediately after an adjective starts with either an H-segment (a segment which triggers the AP-initial H tone) or an L-segment (a segment other than H-segments) were recorded. by 3 Seoul Korean speakers. The F0 values in the syllables containing the consonants in question were then measured. The results show that interaction between the segment type and the branching structure is statistically significant. which suggests that it is difficult to use the phonetic .approach to generalize the relationship between syntax and prosody. Thus, it is concluded that the phonological approach is more valid.

• Journal of the Korea Society for Simulation
• /
• v.11 no.3
• /
• pp.35-48
• /
• 2002

In the work presented here, we describe a method to extract TrueType features for supporting letter recognition. Even if variously existing document processing techniques have been challenged, almost few methods are capable of recognize a letter associated with its TrueType features supporting OCR free, which boost up fast processing time for image text retrieval. By reviewing the mechanism generating digital fonts and birth of TrueType, we realize that each TrueType is drawn by its contour of the glyph table. Hence, we are capable of deriving the segment with density for a letter with a specific TrueType, defined by the number of occurrence over a segment width. A certain number of occurrence appears frequently often due to the fixed segment width. We utilize letter recognition by comparing TrueType feature library of a letter with that from input word images. Experiments have been carried out to justify robustness of the proposed method showing acceptable results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12B
• /
• pp.2320-2334
• /
• 1999

In this paper, we propose multiple IS-MMBS service schemes for very low power and micro-size RMIMS (radio-interfaced micro information monitoring system) terminals. In MMBS service area, when new arrival RMIMS terminals have real-time traffic characteristic or large traffic bandwidth, only single IS-MMBS service scheme can not guarantee RMIMS terminal's QoS(quality of service) such as buffer overflow or packet loss. In this case, the proposed multiple IS-MMBS service schemes can be effectively used for QoS service of RMIMS terminal. According to clustering method of RMIMS terminals and MMBS segment method, the proposed schemes can be divided into terminal segment method, region segment method, application based segment method, traffic type based segment method, overlapping segment method and hybrid segment method

• The Journal of Fisheries Business Administration
• /
• v.48 no.3
• /
• pp.1-14
• /
• 2017

The aim of this study is to examine profiles of consumers in Thai seaweed market segments. A total of 321 consumers were surveyed in bangkok, thailand. The multiple regression analysis performed indicates that consumer preference toward seaweed snack is significantly influenced by seaweed consumption frequency. The cluster analysis performed indicates that there are three segments based on consumer purchasing attributes toward seaweed snack : leading type, pursuing type, beginner type. The results show that there are consumer segment with different purchasing attributes level and seaweed preference. in this study Thai seaweed market's biggest consumer is leading type consumer(n=40.8%) that have high level of purchasing attributes toward seaweed snack when compared to other segments. pursuing type segment(n=27.4%) consists of consumers who have low level of purchasing attributes but have high consumption frequency. beginner type segment(n=31.8%) consists of consumers who rarely eat seaweed snack and have high price sensitivity. This study can inform Thai seaweed consumer's behavior and effective segment market strategies and target consumer based on purchasing behavior toward seaweed snack.