• Journal of Power System Engineering
• /
• v.15 no.6
• /
• pp.53-58
• /
• 2011

To optimization of mlod for fineblanking forming of sector gear of recliner, it was analyzed the effect of clearance, V-ring height, V-ring position, blank holding force and counter punch force. In case of 0.003 mm of clearancs, the finest shear plane was obtained, but optimization between die and punch clearance was 0.005 mm. The height of V-ring was 0.7 mm. In case of increasing of hold force, the size of shear plane got better and the decrement of thickness became smaller. Both the size of shear plane and the decrement of thickness increased according to increasing of counter punch force.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.1
• /
• pp.99-105
• /
• 2010

This study was performed to solve the breaking problem in the fine blanking(FB) process of sector gears for car seat recliner using nickel chrome molybdenum steel(SNCM220) plate. The optimal design of embossing circle is changed to oval with labors' experiences and finite element analysis. The maximum principal stress and effective strain in a forming process are analyzed by commercial finite element software to solve the problems in embossing stage of FB process. As a result of FE analysis, the maximum principal stress in forming is lower than yield point of material. It is shown from experiments in the modified die that the formed gear does not break in embossing stage.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.308-315
• /
• 2002

In recent automotive industries, fine blanking technology widely used in production of components with relatively thick gauges in brake systems, seat recliner, door locks, and auto transmission systems. Due to its advantages to obtain almost final product quality using fine blanking forming process without additional finish machining processes, consequently saving the production costs. In this paper we intended to develope the small sized module gear toothed dual seat recliner sector gear(0.5mm module) for car seats using fine blanking process which needed semi piercing with computer simulation and a lot of try and errors to achieve required accuracy and geometric quality. However through the some corrections of tool geometries with tryout test, we could get successful results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.1
• /
• pp.18-24
• /
• 2007

If an error occurs in a product that contains a source of vibration, an abnormal noise vibration will occur. Recently a system that has been modified from the previous method of noise detection-a method of appraising the quality of manufactured automobile part by using human ears-is being implemented in the industries of automobile parts. This new system distinguishes the product's vibration signals by measuring and analyzing the signals. Following the recent trend, it has been concluded that the appraisal process of Window Regulator Module needed an improvement. Thus, a vibration monitoring system using LabVIEW, which measures and analyzes vibration signals from a sector gear's connected part by using an accelerometer, has been developed. By analyzing the characteristics of vibration signals of both inferior and superior goods, now the quality of the product can be evaluated much more accurately.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1623-1630
• /
• 2010

In this study, effective forming methods for reducing the roll-over of a sector tooth, which is a main component of an automotive seat recliner, are proposed. Due to the large amount of roll-over, accurate contact between the inner gear of a sector tooth and the outer gear of a pawl tooth cannot be normally achieved; thus sensitivity and safety for the passengers decrease. To overcome the aforementioned drawback, we investigated the effect of flowcontrol forming methods involving local embossing die, coining punch, and VIC (Variable Inverse Clearance) on the roll-over depth by FE-analysis and an experiment. The results of a fine-blanking experiment for verifying the proposed methods showed that VIC type is decidedly superior from the aspects of reduction of roll-over and tool strength of the sector tooth.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.12
• /
• pp.44-53
• /
• 2021

As environmental issues have emerged worldwide, emission gas regulations have been strengthened. In the construction machinery sector, studies have been actively conducted to utilize the power source of electric motors owing to the increasing demand for zero emissions. In this study, the gear specifications of an electric axle for construction machinery were selected by considering the specifications of the motor, gear tooth contact pattern, and face load factor. The gear strength evaluation was performed at the system level using the simulation model. The bending and contact strength of the spiral bevel gears and the bending strength of the planetary gear set showed a safety factor of 1 or more. However, the contact strength of the planetary gear set showed a safety factor of 0.92. Conservative results were derived by performing the analysis under the rated load condition of the motor. However, the ratio of the equivalent torque to the rated torque of the motor was 45% or less, hence, it was determined that no difficulties should arise regarding the durability of the axle.

• Journal of Fisheries and Marine Sciences Education
• /
• v.12 no.1
• /
• pp.11-21
• /
• 2000

Most of artificial reefs in the examined areas were normally established except for some lower parts demersed slightly, and some to function. 1) Twenty species of fish were captured by fishing gear, and 10 species were observed by scuba in the examined areas. 2) Five algal and five fisheries animal species were observed as fouling organism. 3) C.P.U.E of trap, long liner and gill netter in the examined areas was respectively 2.12, 10.23, and 4.93, where as that in contral was established as 1.41, 4.43 and 2.86. 4) Species composition by the fishing gear the trap, long liner and gill netter in the examind areas was respectively 94, 85 and 118, where as that in control was established as 58, 37 and 62. Accordingly, The fishing effects in the artificial reefs installation sector was two times higher than comparative sector.

• The Journal of Fisheries Business Administration
• /
• v.54 no.4
• /
• pp.1-18
• /
• 2023

This study examines the significance and problems of the Fourth Amendment to the Fisheries Act, which went into effect in January 2023. Following the passage of the Aquaculture Industry Development Act, the fourth amendment to the Fisheries Act sought to reform the fisheries legislative framework, while also including significant changes. In particular, a number of new systems for managing fishing gear have been implemented, and local governments now have some autonomy in fisheries management, which has allowed for adjustments to be made to meet the needs of the fishing industry and changes in socioeconomic situations. However, as independent legislation for each fisheries sector continues, the subject of regulation under the Fisheries Act, as well as the Act's position as a basic legal system, has been continuously reduced, overshadowing the Act's objective. As a result, a full-fledged assessment of changing the legislation's name in the future is required, as well as addressing issues such as the lack of difference in the legislative purpose clause and the necessity for further revision of the definition clause. Therefore, any future revisions to the Fisheries Act should aim to overhaul the existing framework, including fishing licenses and permits.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.56 no.3
• /
• pp.341-346
• /
• 2023

This study aimed to suggest an alternative income generation (AIG) for local artisanal fisheries communities in the southern coastal area of Bangladesh, which is vulnerable to climate change. To analyze the problems of local artisanal fisheries caused by climate change, field surveys and in-depth interviews with fishermen and government officials were conducted. Livelihood risk factor (LRF) in the marine fishing sector included reduction of fishing days and fish production and damage to fishing vessels and fishing gear due to cyclone and sea-level rise. LRF in the aquaculture sector included cultured fish escape, reduction of aquaculture production, and water pollution due to Monsoon flood. A common challenge for two sectors was high interest rate on commercial loans. Small-scale tank aquaculture is recommended as AIG for securing income of artisanal fisheries communities. In the early stages of dissemination of small-scale tank aquaculture technology, it is necessary to prevent fishermen from struggling to repay high-interest rate loans through technology transfer and facility support by official development assistance. The aquaculture training center, along with the technical education, will also contribute toward expansion of local distribution network and marketing support to establish a value chain for local artisanal fisheries communities.

• Korean Journal of Digital Imaging in Medicine
• /
• v.12 no.1
• /
• pp.9-14
• /
• 2010

Based on the cardiac PACS application collected from three university hospitals across the country, this research showed us a composition method of a server and storage devices with conditions in the field. Also, we founded the practical use of software making the best of cardiovascular PACS features. In addition, it also examined the components and requirements of the key functions that are available in the cardiovascular sector. We will be investigated the design experience and applications on stable storage and transmission of large video clip data, cardiovascular analysis, and gear interlocks through the study.