• Journal of Mechanical Science and Technology
• /
• v.15 no.11
• /
• pp.1463-1471
• /
• 2001

The Kachanov and Rabotnov (K-R) creep damage model was interpreted and applied to type 316LN and HT-9 stainless steels. Seven creep constants of the model, A, B, $textsc{k}$, m, λ, ${\gamma}$, and q were determine d for type 316LN stainless steel. In order to quantify a damage parameter, the cavity was interruptedly traced during creep for measuring cavity area to be reflected into the damage equation. For type 316LN stainless steel, λ= $\varepsilon$R/$\varepsilon$* and λf=$\varepsilon$/$\varepsilon$R were 3.1 and increased with creep strain. The creep curve with λ=3.1 depleted well the experimental data to the full lifetime and its damage curve showed a good agreement when r=24. However for the HT-9 stainless steel, the values of λ and λf were different as λ=6.2 and λf=8.5, and their K-R creep curves did not agree with the experimental data. This mismatch in the HT-9 steel was due to the ductile fracture by softening of materials rather than the brittle fracture by cavity growth. The differences of the values in the above steels were attributed to creep ductilities at the secondary and the tertiary creep stages.

• Journal of the Korean GEO-environmental Society
• /
• v.1 no.1
• /
• pp.35-42
• /
• 2000

The settlement characteristics of waste landfill site must be considered in the design of sanitary landfill as well as in the course of the rehabilitation of the landfill site. Among prediction methods for settlement of landfill site, especially Gibson and Lo model and Power Creep Law have been successfully applied to the landfill site where the amount of settlement was large and the secondary settlement was obvious. Therefore, the effects of organic content on the model parameter values utilized in both Gibson Lo model and Power Creep Law were studied by using a large consolidation testing apparatus. The organic content is each 20%, 40%, 60% of total volume and consolidation load is $0.1{\sim}1.6kg/cm^2$. The main results can be summarized as follows: (1) The reference compressibility of Power Creep Law is decreased according to the increments of consolidation load: (2) The field measurement is more similar to the Power Creep Law than the Gibson and Lo model.

• Proceedings of the Korean Reliability Society Conference
• /
• 2006.05a
• /
• pp.158-164
• /
• 2006

The creep behavior of newly developed composite geogrids which consists of PET yarns sheathed in PP were evaluated using SIM. For the SIM procedure, three test parameters, the applied loads, temperature steps and number of ribs were investigated, The study confirmed that temperature steps of 10 and 14$^{\circ}C$ up to 80$^{\circ}C$ are applicable for composite geogrids due to the different transition temperatures between two materials. At applied loads of 40 and 50%, only primary creep state was measured, while secondary creep state appeared at the applied loads of 60%, The lifetimes of composite geogrids were estimated at each of loading level using statistical reliability analysis technique. The results show that the lifetimes longer than 100 years can be predicted within 16 hours. Therefore, SIM is very effective and economical accelerated creep test methods, especially for lifetime prediction. This gives guidelines for users to select the appropriate factor of safety against creep considering the field condition within shorter test times.

• Nuclear Engineering and Technology
• /
• v.52 no.7
• /
• pp.1481-1485
• /
• 2020

The creep behavior of Ni-Cr-W alloy at 950 ℃ has been investigated by a novel creep testing system which is capable of in-situ measurement of strain. Tubular specimens were pressurized with argon gas for effective stresses up to 32 MPa. Experimental results show that the thermal fatigue reduces the creep life of the tubular specimens and with the introduction of thermal cycling fatigue the primary stage disappears and the creep rate higher than the pure thermal creep (without thermal fatigue). Also the creep behavior of Ni-Cr-W alloy doesn't consist in the secondary stage. A new creep equation has been derived and implemented into finite element method. The results from the finite element analyses are in good agreement with the creep experiment.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.4
• /
• pp.235-241
• /
• 2005

Thermal creep properties of the advanced zirconium fuel claddings named by HANA alloys which were developed for high burn-up application were evaluated. The creep test of HANA cladding tubes was carried out by the internal pressurization method in temperature range from 350 to $400^{\circ}C$ and in the hoop stress range from 100 to 150 MPa. Creep tests were lasted up to 800 days, which showed the steady-state secondary creep rate. The creep resistance of HANA fuel claddings was affected by final annealing temperature and various factors, such as alloying element, applied stress and testing temperature. From the results the microstructure observation of the samples before and after creep test by using TEM, the dislocation density was increased in the sample of after creep test. The Sn as an alloying element was more effective in the creep resistance than other elements such as Nb, Fe, Cr and Cu due to solute hardening effect of Sn. In case of HANA fuel claddings, the improved creep resistance was obtained by the control of final heat treatment temperature as well as alloying element.

• Korean Journal of Materials Research
• /
• v.14 no.7
• /
• pp.451-456
• /
• 2004

Thermal creep properties of the zirconium tube which was developed for high burnup application were evaluated. The creep test of cladding tubes after various final heat treatment was carried out by the internal pressurization method in the temperature range from $350^{\circ}C to 400^{\circ}C$ and from 100 to 150 MPa in the hoop stress. Creep tests were lasted up to 900days, which showed the steady-state secondary creep rate. The creep resistance of zirconium claddings was higher than that of Zircaloy-4. Factors that affect creep resistance, such as final annealing temperature, applied stress and alloying element were discussed. Tin as an alloying element was more effective than niobium due to solute hardening effect of tin. In case of advanced claddings, the optimization of final heat treatment temperature as well as alloying element causes a great influence on the improvement of creep resistance.

• Journal of the Society of Disaster Information
• /
• v.4 no.2
• /
• pp.52-66
• /
• 2008

It has been a growing concern about reusing Sudokwon landfill 2nd site and other sanitary landfills located around the metropolitan areas. In this paper, settlement characteristics of Sudokwon landfill 2nd site were studied by analyzing the data collected over the period of six years. Three equations are combined in order to modeling the long-term settlement behavior of refuse landfill caused by mechanical secondary composition and secondary composition caused by the decomposition of biodegradable refuse. It is suggested that mechanical secondary composition is linear with respect to the logarithm of time. The models proposed by hyperbolic method and Gibson & Lo model, power creep law are considered to be suitable for the long-term prediction value of Sudokwon landfill 2nd site. The fifteen-year-period prediction value of hyperbolic method and Gibson & Lo model is considerably different from that of power creep law model. The average settlement for Block I in Sudokwon 2nd site is approximately 3.9m with 4 steps of final landfill stages.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.2 no.2
• /
• pp.59-66
• /
• 1990

Various types of ice distribution under low temperature greatly influence the environment of the Arctic and Antarctic Oceans. To understand fundamentals of ice properties such as Polar glaciers, icebergs and sea ice, this study focuses on the material behaviors and failure mechanisms of polycrystalline ice. Utilizing the continuum damage theory, a three-dimensional constitutive model to describe creep deformation characteristics in the glacial flow is developed in consideration of micro-cracking as the major physical process of ice deformation. The numerical model is compared with the published experimental data especially in uniaxial constant stress creep tests. The model can simulate primary and secondary creeps as well as tertiary creep characteristics due to the microcrack accumulation.

• Geomechanics and Engineering
• /
• v.28 no.2
• /
• pp.157-169
• /
• 2022

Preloading of soft clays is a common ground stabilization method for improvement of compressibility and the undrained shear strength. The waiting period under preload is a primary design criterion controlling the degree of improvement obtained. Upon unloading the overconsolidation attained with respect to actual loads defines the long term performance. This paper presents a laboratory study for investigation of creep behavior of Famagusta Bay alluvial soft soil preloaded under various effective stresses for analysis of long term performance based on the degree of overconsolidation. Traditional one-dimensional consolidation tests as well as modified creep tests are performed on reconstituted soft specimens. Compressibility parameters are precisely backcalculated using one dimensional consolidation theory and the coefficient of creep is determined using the traditional Cassagrande method as well as two modified methods based on log cycles of time and the inflection of the creep curve. The test results indicated that the long term creep can be successfully predicted considering the proposed method. The creep coefficients derived as part of this method can also be related to the recompression index (recompression index, swelling index) considering the results of the testing method adopted in this study.

• Geomechanics and Engineering
• /
• v.24 no.1
• /
• pp.43-55
• /
• 2021

Peatland is distributed in China widely, and organic matters in soil frequently induce problems in the construction and maintenance of highway engineering due to the high permeability and compressibility. In this paper, a selected site of Dali-Lijiang expressway was surveyed in China. A numerical model was built to predict the settlement of the foundation of the selected section employing the soft soil creep (SSC) model in PLAXIS 8.2. The model was subsequently verified by the result of field observance. Consequently, the parameters of 17 types of soils from different regions in China with organic contents varying from 1.1-74.9% were assigned to the numerical model to study the settlement characteristics. The calculated results showed that the duration of primary consolidation and proportion of primary settlement in the total settlement decreased with increasing organic content. Two empirical equations, for total consolidation settlement and secondary settlement, were proposed using multiple linear regression based on the calculated results from the numerical models. The analysis results of the significances of certain soil parameters demonstrated that the natural compression index, secondary compression index, cohesion and friction angle have significant linear relevance with both the total settlement and secondary settlement, while the initial coefficient of permeability exerts significant influence on the secondary settlement only.