• The Journal of Engineering Geology
• /
• v.7 no.2
• /
• pp.113-126
• /
• 1997

Electrical resistivity methods of dipole - dipole array profiling and Schiumberger array sounding were tested on a segment of the Woraksan granitic batholith for the research into the imaging of irregular attitudes of fracture zones in the crystaaline rock in terms of processing and interpretation schemes. By the dipole - dipole array method, inhomogeneities such as small scale of fracture zones were properly delineated down at some depth even within hard rock environment. Fracture zones were interpreted to be at the boundaries between the high amplitude zone and very low amplitude zone in the resistivity plot and they were also successfully outlined in two - dimensional layer and pseudo - three - dimensional volume constructed by the incorporation of vertical sounding data. The surface location of the fracture zones was correlated by the zero - crossing point in the VLF(very low frequency) electromagnetic data. Pseudo - three - dimensional attitudes of fracture zones were efficiently illuminated by optimum projection angle. The mean of bulk resistivity for the Woraksan granite and the near fracture zones is estimated to be approximately of 4,000 ohm - m which is much higher than the value of 700 ohm - m for the Rwachunri limesilicate environment. This difference is due to both the rock type, i.e., biotite granite vs limesilicate, and the occurrence of secondary openings of fold and fault associated with the intrusion of granite. In this study statistical analyses on the resistivity color plot were performed in terms of three representative statistical moments, i.e., standard deviation, skewness, and kurtosis. The fracture zones in the standard deviation plot were characterized by the higher value, compared to the value of homogeneous portion. The upper boundary of the high resistivity zone was also successfully delineated in the skewness and kurtosis plots.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.5
• /
• pp.121-133
• /
• 2017

Since the mid 1990s, policies have been actively promoted to improve safety and pedestrian environment around the school such as the improvement of School zone. However, the prevention of accidents was not effective because it did not extend to the school road where the main transportation route for children's commuting takes place. In addition, due to the rapid increase of automobiles, trunk road traffic in the peak time bypasses the back roads, which threatens children's safety and the environment by invading the school area, which is the main living space of children. In this study, the characteristics of domestic children's traffic accidents were investigated and the problems were analyzed by conducting a field survey on Yeouido Secondary School in Seoul and Unjung Elementary School in Gyeonggi Province. In addition, Variable speed limit signs and Beacons were installed in the pedestrian road of comunity including School zone, and the effects of facilities on the speed of vehicles were analyzed. As a result of the analysis, the Variable speed limit sign showed a deceleration effect of about 8.3km/h, and the Beacon showed a phenomenon in which the traveling speed of 0.8km/h increased only slightly. In addition, the traffic violation rate of passenger cars, buses, and lorries decreased by about 3% as a result of investigating the number of traffic violation vehicles before and after installation.

• Korean Journal of Environment and Ecology
• /
• v.32 no.1
• /
• pp.118-131
• /
• 2018

The forest vegetation of Juwangsan National Park, which is famous for its towering scenic valleys, was syntaxonomically described. The study adopted the $Z{\ddot{u}}rich$-Montpellier School's method emphasizing a matching between species composition and habitat conditions. A combined cover degree and the r-NCD (relative net contribution degree) were used to determine a performance of 265 plant species listed-up in a total of 52 phytosociological $relev{\acute{e}}s$. Nine plant communities were classified through a series of table manipulations, and their distribution and actual homotoneity($H_{act}$) were analyzed. Syntaxa described were Carex gifuensis-Quercus mongolica community, Athyrium yokoscense-Quercus mongolica communiy, Arisaema amurense-Quercus serrata community, Lespedeza maximowiczii var. tomentella-Quercus variabilis community, Tilia rufa-Quercus dentata community, Carex ciliatomarginata-Carpinus laxiflora community, Aristolochia manshuriensis-Zelkova serrata community, Onoclea orientalis-Fraxinus mandshurica community, and Carex humilis var. nana-Pinus densiflora community. A zonal distribution was reviewed and the altitude of about 700 m was the transition zone between the cool-temperate central montane zone (Lindero-Quercenion mongolicae region) and southern submontane zone (Callicarpo-Quercenion serratae region). Only 19 taxa were associated with r-NCD 10% or more, most of which were tree species occurring in the Lindero-Quercenion and some of which was a member of open forests. Species composition of forest vegetation was much less homogeneous, showing the lowest $H_{act}$. Nearly natural forests and/or secondary forests in the Juwangsan National Park were defined as a regional vegetation type, which reflects much stronger continental climate in the Daegu regional bioclimatic subdistrict, rhyolitic tuff predominant, and wildfire interference.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.372-380
• /
• 1999

The purpose of this study was to investigate the distribution of calcitonin gene-related peptide(CGRP) containing nerve fivers after pulp exposure in rats. The Spague-Dawley rats weighing about 250 - 300g were used. The animals were devided into normal control group and experimental groups. Experimental animals were sacrified on 2, 4, 7, 10 days after pulp exposure. The maxillary teeth and alveolar bone were removed and immersed in the 4% paraformaldehyde plus 0.1M phosphate buffer (pH 7.4). Serial frozen $50{\mu}m$ thick sections were cut with a cryostat. In the immunohistochemical staining procedure, the rabbit CGRP antibody was used as a primary antibody. The sections were incubated for 48 hours at $4^{\circ}C$, and placed into biotinylated anti-rabbit IgG as a secondary antibody and incubated in ABC (avidin-biotin complex), The sections were visualized by 0.05% 3.3 diaminobenzidine tetrahydrochloride. The results of this study were as follows: 1. In control group, CGRP containing nerve fibers ran parallel to the long axis of root and reached the coronal pulp. They were distributed on Raschkow plexus under the odontoblastic layer. 2. In 2 day group after pulp exposure, tissue necrosis and acute inflammation occurred and CGRP containing nerve fibers increased. In 4 day group, the necrotic tissue extended to the pulp and CGRP containing nerve fibers were distributed around the inflammation zone. 3. In 7 day group after pulp exposure, pulp necrosis occurred, and in 10 day group, the abscess under the necrotic pulp extended to the root apex area and CGRP containing nerve fibers were not observed in root canals. 4.The sprouting of CGRP nerve fibers was most remarkable at the pulp chamber under injury in 4 day group, and it was found at inflammation zone under the necrotic tissue in 7 day group and the remaining root pulp tissue in 10 day group. As mentioned above, CGRP nerve fibers had a tendency to increase around the inflammatory zone, especially around the acute inflammation tissue, when compared with control group. It is suggested that CGRP nerve fibers maybe related to the control of inflammatory response of pulp tissue.

• Clean Technology
• /
• v.26 no.3
• /
• pp.211-220
• /
• 2020

This experimental study investigates the design parameters to achieve ultra low NOx combustion of coal using a 80 kW capacity single-burner furnace. The influence of key design parameters such as SN, overall and burner-zone equivalence ratios, primary/secondary air ratio, overfire air (OFA) ratio were tested for a total of 81 cases. The results showed that weak swirl intensity of the burner leads to higher NOx emission whereas strong swirl intensity accompanies increased CO concentration desipte lower NOx emission. Therefore, finding an appropirate swirl intensity is essential for the burner design. Larger flow rate of secondary air increased NOx emission, whereas smaller flow rate stretches the flame and increased CO emission. The lowest NOx emission of 82 ppm (6% O₂) was achieved at the optimal condition of the present burner deisgn. It is expected to furrther lower the NOx emission by introducing splitting the burner secondary air into three or four streams.

• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.290-299
• /
• 2000

A three-dimensional model was developed in order to simulate heat and fluid flow of a continuous casting billet. The model was coded with the general-purpose CFD program FIDAP, using the finite element method. The present model consists of 2 individual calculation schemes, named model 1 and model 2. Mold region only was calculated to check the pouring stream through submerged nozzle with model 1. Entire region, which consists of mold, secondary cooling, radiation cooling was calculated to predict crater end position, temperature profile and solid shell profile(model 2). Standard $k-{\bullet}\hat{A}$ turbulence model has been applied to simulate the turbulent flow induced by submerged nozzle. Enthalpy method was adopted for the latent heat of solidification. Fluid flow in mushy zone was treated using variable viscosity approach. The more casting speed and superheat increased, the more metallurgical length increased. The shell thickness at the mold exit is proved to be mainly controlled by superheat by the present simulation. It may be concluded that the present model can be successfully applied far the prediction of heat and fluid flow behavior in the continuous casting process.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.361-371
• /
• 2000

A demand of marine outfall system has been much increased for the effective disposal of the wastewater due to population and industrial development at the coastal areas. The outfall system discharges primary or secondary treated effluent into the coastline, or at the deep water, or between these two. The discharge is carried out by constructing a pipeline on the sea bed with a diffuser or with a tunnel, risers and appropriate. The effluent, which has a density similar to that of fresh water, rises to the sea surface forming plume or jet, together with entraining the surrounding salt water and becomes very dilute. Thus there have been growing interests about plume behaviour around the outfall system. Plume or jet discharged from single-port or multi-port diffuser might cause certain impacts on coastal environment. Near field mixing characteristics of discharged water field using CORMIX model have been studied for effective outfall design various conditions on ambient current, depth, flow rate, effluent concentration, diffuser specification, port specification etc.. This kind of analysis is necessary to deal with water quality problems caused by the ocean discharge. The analyzed result was applied to the Pusan Jungang effluent outfall system plan.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.637-643
• /
• 2011

The bond-based peridynamic model is able to capture many of the essential characteristics of dynamic brittle fracture observed in experiments: crack branching, crack-path instability, asymmetries of crack paths, successive branching, secondary cracking at right angles from existing crack surfaces, etc. In this paper we investigate the influence of the stress waves on the crack branching angle and the velocity profile. We observe that crack branching in peridynamics evolves as the phenomenology proposed by the experimental evidence: when a crack reaches a critical stage(macroscopically identified by its stress intensity factor) it splits into two or more branches, each propagating with the same speed as the parent crack, but with a much reduced process zone.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.149-158
• /
• 2000

After measuring actual stress by two measurements(Dynamic Strain Meter, Histogram Recorder) on truss rail road bridge, we could perform time history analysis by 3-D beam element method on modelling bridge. And then, after analyzing bridge structure in static by 3-D modelling, we estimated degree of fatigue damage in main member, secondary member of tie zone, cutting area of base metal cross section for confirming the result. In case that the simulated stress is carried out on modeling bridge, most of those simulation mainly is performed by main members. But in real bridge fatigue damage problems generally caused by junctions, connections, joints in which especially local stress is activated. Therefore, in this paper actual stress on critical area was estimated through the analysis result by simulation. With this study, we can estimate the degree of fatigue damage from a safety point of view and comparative accuracy.