• 한국터널지하공간학회 논문집
• /
• 제21권2호
• /
• pp.301-321
• /
• 2019

본 논문에서는 강관다단 그라우팅에 적용하는 속경성 실링재 개발에 관한 실험적 내용을 다루었다. 강관다단 그라우팅 공법에서 실링재는 본 주입재의 주입시 역류를 방지하기 위해 주입하며 주입 후 일정시간이 지난 다음 겔화 상태에서 본 주입재를 주입해야 한다. 그러나 주입된 실링재가 겔 상태가 되기 이전 유동성이 있을 경우 본 주입재와 함께 혼합됨은 물론, 주입재의 역류가 발생되어 원지반으로 주입이 곤란하며, 반대로 너무 시간이 지나 겔화단계를 넘어 고결되었을 경우 본 주입재가 지반내로 주입되지 못하는 경우가 발생된다. 실링재의 유동성이 없어져 겔화 상태로까지 걸리는 시간에 따라 강관다단 그라우팅의 공사시간이 결정되며, 이는 전체 터널의 공사기간과 밀접한 관련이 있어 중요한 요소 중에 하나이다. 따라서 본 연구에서는 실링재 본연의 역할과 기능을 할 수 있을 뿐 아니라 공사기간을 단축시킬 수 있도록 실링재의 겔화시간을 단축시킬 수 있는 칼슘알루미네이트 재료를 개발하였고, 실링재 겔화 여부를 판단하는 방법에 대해 제시하고, 아울러 실링재의 겔 상태에서 블리딩율에 대해서도 각 품질기준과 시험방법에 대해 제안하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.476-479
• /
• 1997

A Knowledge of friction force in pneumatic cylinders makes it possible to improve cylinder description during simulation and to asses performance under changing operating conditions more accurately. Such knowledge is particularly useful, for example, when modeling continuous pneumatic positioning systems or predicting the operating conditions under which stick slip may occur, as well as in establishing preventive maintenance procedures for pneumatic cylinders. Friction force depends on a number of factors, including operating pressure, seal running speed on the cylinder barrel and rod, barrel material and surface roughness, seal dimensions and profile, seal material, lubrication conditions, cylinder distortion during assembly, and the operating temperature of cylinder components. This paper shows a system for measuring the friction force caused by a seal used in pneumatic cylinders. Results of experimental tests show that seal friction forces for grease lubricated service are clearly dependent on speed and pressure and are les sensitivity to other parameter. i.e., barrel material and roughness, seal material, and profile.

• 한국압력기기공학회 논문집
• /
• 제11권1호
• /
• pp.25-32
• /
• 2015

Many crack flaws have been detected at tubing seal weld zone in Steam Generator with Alloy600 material tubes. it is very difficult to discriminate the signal from parent material and that from weld zone because weld zone gives complicated ECT signal due to manufacturing processes. ECT signal analysis in the seal weld zone is very important since the tubes with crack in this area shall be out of service by plugging. The purpose of this paper is to distinguish between Parent material and Weld Zone ECT signal in the seal weld zone through the demonstration test of Steam Generator seal weld mock-up.

• Tribology and Lubricants
• /
• 제22권6호
• /
• pp.314-319
• /
• 2006

In this paper, the friction and wear characteristics of contact type sealing unit far a water turbine have been presented. The sealing unit for a small hydropower generation is to stop a leakage of circulating water from an outside of an impeller to an inside of a rolling bearing. The friction heating between a seal ring and a seal seat may radically increase a surface temperature in which increase a power loss and wear on the rubbing surface. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Victors hardness and the hardness of silicone carbide of SiC is 714.1 in Victors hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces are a dry friction, a water film friction and a mixed friction that is contaminated by a dust, silt, and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat in primary sealing unit. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.515-518
• /
• 2006

This paper presents the friction and wear characteristics of contact type sealing unit for a water turbine of a small hydro-power generation, which Is to stop a leakage of a circulating water from a outside of an impeller to an inside of a rolling bearing. The surface wear strongly affect to the seal life of a mechanical face seal. In this study, the hardness of a stainless steel in which is a heat-treated is 892.8 in Vickers hardness and the hardness of silicone carbide of SiC is 714.1 in Vickers hardness. The surface hardness of a heat-treated stainless steel is 25% high compared with that of a ceramic material of SiC. The contact modes of rubbing surfaces aye a dry friction a water film friction and a mixed friction that is contaminated by a dust, silt and moistures, etc. These two factors of a contact rubbing modes and a material property are very important parameters on the tribological performance such as a friction and wear between a seal ring and a seal seat. The experimental result shows that the surface hardness of a seal material is very important on the friction coefficient and a wear volume. Thus, the results recommend higher hardness of a seal material, which may reduce a friction loss and increase a wear life of primary seal components

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.123-124
• /
• 2006

Usually, hydraulic cylinder is widely used as the actuator in the equipment of construction machines, airplane and military machines. In case of these devices, due to use under severe environment such as water, $SiO^2$ and dust, etc. seal which has high packing ability and long service life has been required. These characteristics are largely influenced by material and geometries of seal such as approach angle, withdrawal angle and interference. Recently, many a study about seal material has been performed so that many materials have been developed. But the concrete studies including the relationships between geometry of seal and sealing performance have hardly been performed yet. Therefore, in this study, we predicted the deformation behavior and contact normal distribution of dust seal with the variation of geometries of seal lip using finite element analysis. And based on the results of analyses, we discussed the effects of the design variables fur sealing performance of the dust seal.

• 한국터널지하공간학회 논문집
• /
• 제22권4호
• /
• pp.367-381
• /
• 2020

본 연구는 강관다단 그라우팅 공법의 Seal재의 배합비 결과에 대한 연구이다. 현재 국내에는 Seal재의 적정 겔화시간 및 초결시간에 대한 명확한 기준이 없는 실정이며, 이를 확인할 수 없어 품질관리에도 어려움이 있다. 이에 Seal재의 배합비를 4가지로 구성하여 실내 실험을 진행하였으며, 이를 통해 겔화시간 및 블리딩양을 확인하였다. 또한 비카트침 관입 실험을 통해 초결시간을 확인하고 각 배합비의 비교를 진행하였다. 그리고 W/C 120%에 대한 추가적인 실험을 통해 교반 속도와 시간이 Seal재에 미치는 영향을 파악하였다. 실내실험을 기반으로 총 3가지의 배합비에 대한 현장 실험을 진행하였으며, 시료의 초결시간 확인 및 본주입을 통한 구근 형성 크기와 강도를 비교하였다. 비교 결과 W/C가 낮을수록 강도가 강하고 구근의 크기가 크며, 초결 시간이 빠르게 나타나는 결과를 확인하였다. 겔화시간과 초결시간 결과를 통해 실제 현장에 적용 시 W/C 120%의 배합비가 가장 적절할것으로 나타났다.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.88-94
• /
• 2006

A typical disk brake system consists of caliper housing, piston, seal and two pads etc. The configuration of seal groove, dimension of piston and seal, and seal material properties are important ones for brake performance, as these affect the retraction of piston. The rubber seal is designed to perform dual functions of sealing the brake oil at brake-applied and retracting the caliper piston at brake-released. In this paper, the seal stress is analyzed using Finite Element Method and experiment is conducted by Taguchi's Method. We attempt to quantify the critical design factors in the seal groove and evaluate their impact on some of brake performance factors. The investigation obtained from this study can not only enhance the seal groove design optimization, but also reduce product prototype testing and development time.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1576-1580
• /
• 2007

Typical lip seals are widely used as sealing mechanism of rotary and reciprocating shaft. Double lip seal has comparatively high stiffness and dynamic radial eccentricity. Usually material of these seals is made of elastomer and nonlinear finite element analysis is required to analyze behaviour of this material because Young's modulus is varied with working load. In this paper, MSC MARC/MENTAT is used for nonlinear analysis of double lip seal with pressure variation and interference. The contact normal force of double lip seal between lip and shaft is analyzed to reduce power loss when shaft rotates.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.22-27
• /
• 2002

The existing compressor steel seal used in automotive air-conditioner has the problem of oil leakage and the deterioration in shielding performance, due to the abrasion and the corrosion of the material. A new type of polymer resin seal is studied in the research. The polymer resin seal has the characteristics of high anti-abrasiveness and anti-corrosiveness, which can overcome the deflects of the steel seal. In addition, the seal needs lower manufacturing cost and is appropriate to mass production, because it is made by the injection molding method requiring no mechanical processing. The profile generation program for seal mold has been developed using the gradient method, and the molding characteristics of the seal have analyzed through the flow analysis and the warpage analysis. The program has been verified by comparing the analysis results with the measured data of the test product. The research might be said to provide the basic method to produce the polymer resin seals with various types and dimensions.