• 대한조선학회논문집
• /
• 제51권3호
• /
• pp.254-258
• /
• 2014

Field trial in ice-covered sea is one of the most important tasks in the design of icebreaking ships. To correctly estimate ice load and ice resistance on ship's hull, It is essential to understand the material properties of sea ice during ice field trials and to perform the proper experimental procedure by gathering sea ice data. A measurement of sea ice properties was conducted during February and March of 2012 with the Korean Icebreaking research vessel "ARAON" in the Amundsen Sea, Antarctica. This paper describes a test procedure to obtain sea ice data which provide basic information to estimate ice loads and icebreaking performance of the ship. The data gathered from sea ice field trials during the 2012 Antarctic voyage of the ARAON includes ice temperature/salinity/density and the compressive/flexural strength of sea ice. This paper analyses the gathered Antarctic sea ice material properties comparing with the previous data obtained during ARAON's Arctic and Antarctic voyages in 2010.

• 대한조선학회논문집
• /
• 제47권3호
• /
• pp.462-468
• /
• 2010

A new course keeping controller for RIB(Rigid Inflatable Boat)-type USV(Unmanned Surface Vehicle) is developed using pilot's steering pattern. A pilot's simple steering pattern is found out from various course change tests. It is used to course keeping algorithm, suitable for large course change more than 60 degrees. To validate the course keeping controller, sea trial tests are conducted. From sea trial test, new course keeping controller shows good performance with less overshoot, maximum roll angle less than $20^{\circ}$, which makes it possible that fast course changes without slip motion of USV.

• 한국해양환경ㆍ에너지학회지
• /
• 제5권2호
• /
• pp.50-61
• /
• 2002

본 연구는 '해양폐기물 수거선박 요구조건 및 선단구성[1]'의 후속연구로서, 주로 서해안 그리고 남해안 일부를 대상으로 하는 천수용 다기능 해양폐기물 수거시스템의 초기 개념설계 결과에 대하여 논한다. 일일 수거 목표량을 포함하는 수거 시스템의 임무를 도출하고, 요구조건에 부합되는 초기 개념설계, 일반배치를 수행하였다. 또한, 구성된 수거 시스템의 타당성 검토를 위하여 복원성 검토, 컴퓨터 그래픽 시뮬레이션 작업을 수행하였다. 마지막으로, 전남여수항 실해역에서 시스템 검증실험을 수행하였으며, 결과로서 개발된 시스템의 효용성, 타당성이 입증되었다.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.366-374
• /
• 2021

This paper presents the analysis of the speed-power performance in the real sea using a large container vessel data provided as a test bed from a shipping company. To perform a speed trial of the vessel during a commercial voyage, the on-board measuring device and various operation data acquisition systems were mounted on the vessel for long-term performance monitoring and the voyage operated under the container loading condition close to the design draft was adopted. The content of this paper consists of Part I and Part II. Part I, such as this paper, contains the speed trial method and analysis results of the operating vessel. Part II contains the analysis of the speed-power characteristics change over time and before and after hull cleaning using operation data measured from the voyage operated under a condition similar to the speed trial.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권5호
• /
• pp.606-613
• /
• 2007

The 6m class high speed boat is developed with a durable hull and inflatable tube, which is called RIB(Rigid Inflatable Boat), for the purpose of marine leisure. In the stage of the conceptual design, its requirements to be optimized are determined based on the presented information of similar marine leisure RIBs. The 3-D graphical technique using Marine Rhino is utilized to optimize the compartment layout of RIB. The stability analysis is performed for the light and full load conditions with and without the inflatable tube. In addition, the sea keeping and hydrodynamic performance was tested using the proto-type ship in the sea condition. From the results of the computation and the sea trial test, it shows that the performance of the marine leisure RIB satisfies the speed, the convenience, and the stability requirements. This study provides the typical information of the design factors and the procedure to manufacture the marine leisure RIB.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 한국해양환경ㆍ에너지학회지
• /
• 제5권2호
• /
• pp.62-67
• /
• 2002

본 연구는 '천수용 다기능 해양폐기물 수거시스템 개발(PART I 초기 개념설계)'의 후속연구로서, 천수용 다기능 해양폐기물 수거시스템의 시스템 구성 및 성능시험 결과에 대하여 논한다(조[2003]). 수거깊이 15미터 이내의 항내 침적폐기물의 수거를 위한 다관절 수거시스템과 100미터 이내의 예인식 수거시스템이 개발되었다(해양수산부[2001]). 다관절 수거시스템은 부유폐기물, 침적 잔여폐기물의 수거, 작업의 고효율화를 위한 스틸와이어커터 시스템도 포함이 되어 다기능화 되어있다. 이 시스템의 시제품을 제작하여 수심이 낮은 해역에서 실해역 시운전을 수행, 시스템의 성능검증을 수행하였다. 결과로서, 개발된 시스템은 안전하고 원활하게 작동되어 시스템의 타당성을 입증하였다.

• 한국군사과학기술학회지
• /
• 제13권4호
• /
• pp.569-576
• /
• 2010

Jamming simulator has developed for the purpose of the test and evaluation on the electronic protection capabilities of the tracking radar onboard ship. This simulator has the capabilities to generate and radiate the jamming signals against the radar as well as those to receive, analyze and identify the radar signals at a real sea environment. The limited space of ship superstructure has led to the serious distortion caused by the ring around phenomenon that some sidelobes of the jamming beams were coming back to the receiving antenna. In this paper, we have proposed the methods to eliminate the ring around. First, we have inserted the groove metal screen between transmitting and receiving antennas. Second, we have used the PRI(Pulse Repetition Interval) tracking loop to control the switching timing of the input radar and the output jamming signal. Finally, we have demonstrated the performance and effectiveness of the proposed methods through the sea trial.

• 한국해양공학회지
• /
• 제32권6호
• /
• pp.518-526
• /
• 2018

As a new technical approach, this paper introduces a method for improving an electrically propelled outboard motor in consideration of the driving system applied to an electric-propulsion boat with solar cell energy. The most efficient model for a drive shaft, propeller shaft, and bevel gear was suggested and examined with respect to the results of test operation in prototype mode. Furthermore, this research included a performance evaluation of the manufactured prototype to acquire the purposed quantity value and the development items. After manufacturing the desired prototype of an electrically propelled outboard motor, the maximum sail time, thrust force, noise, and weight were evaluated in a performance test. An additional test in relation to the maximum sail speed (knots) of the completed prototype was conducted using a sea trial evaluation to acquire the optimum quantity.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.727-730
• /
• 2004

Reduction of a ship's rolling is the most important performance requirement for improving the safety of the crew on board and preventing damage to cargos as well as improving the comfort of the ride. A mass driving anti-rolling system (MD-ARS) might be one candidate of several systems against the ship's rolling. In this paper, three types of MD-ARS, two passive and one active devices, are developed for small ships. After they are installed on the cabin of the small leisure boat, respectively, a series of test is conducted before and after operating them. Through the test, it is confirmed that the roll responses of the ship are pretty well reduced by the system.