• 대한조선학회논문집
• /
• 제48권5호
• /
• pp.457-464
• /
• 2011

This paper deal with the validation of correction method of ice strength and thickness to the sea trial condition based on the ice model test results. It is very difficult to conduct the model test corresponding to the sea trial condition exactly. In addition, the available sea trial data is not sufficient for the validation of correction method. In the present study, the model test results of Terry-Fox ice breker have been used to compare the corrected results of sea trial test by varying its thickness and strength of model ice. The HSVA and ITTC methods have been applied to the present comparisions and the required power has been also validated by using the HSVA method. There are rather good agreement between the sea trial result and model test corrected by the HSVA and ITTC method. The more comparisons are expected to be carried out in near future.

• 한국항해항만학회지
• /
• 제34권8호
• /
• pp.623-628
• /
• 2010

현재 모형선을 이용한 선형성능 검증설비는 예인수조와 회류수조 두설비가 주로 이용된다. 이들 설비는 주로 저속 대형선박을 위해 기법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기에 전차의 속도와 유속이 목표속도에 미치지 못해 어려움이 존재한다. 따라서 고속 선박의 저항성능 평가를 위해 새로운 기법 정립 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실제 해상에서 선박을 이용한 모형시험을 고안하고 측정시스템을 구성하였다. 시스템구성은 총 8개의 파트로 구성되어 있으며, 시스템 검증을 위해 C.W.C에서 저속선의 모형을 이용하여 시험을 수행하여 시스템 적용 가능성을 검증하였다. 또한 실제 해상에서 고속선 모형선을 이용하여 시험을 수행하였으며, 이 결과를 CFD해석 결과와 비교하여 실해상 모형시험 방법의 가능성을 확인 하였다.

• Journal of Ship and Ocean Technology
• /
• 제5권4호
• /
• pp.44-50
• /
• 2001

Large container carriers are suffering from lack of knowledge on reliable correlation allowances between model tests and full-scale trials, especially at fully loaded condition, Careful full-scale sea trial with a full loading of containers both in holds and on decks was carried out to clarify it. Model test results were analyzed by different methods but with the same measuring data to figure out appropriated correlations factors for each analysis methods, Even if it is no doubt that model test technique is one of the most reliable tool to predict full scale powering performance, its assumptions and simplifications which have been applied on the course of data manipulation and analysis need a feedback from sea trial data for a fine tuning, so called correlation factor. It can be stated that the best correlation allowances at fully loaded condition for both 2-dimensional and 3-dimensional analysis methods are fecund through the careful sea trial results and relevant study on the large size container carriers.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.800-807
• /
• 2006

Sea dyke construction is simply defined that the cutting procedure of sea water flow. Sea dyke construction is more difficult than in-land construction because it’s placed on deep seabed and exposed sea wave attack. Especially, the final closure of sea dyke is most dangerous due to the fast velocity of tidal flow. The final closure section is consisted with vast rubble and heavy stone gabion, therefore the discharge velocity at land side of final close section is irregularly and sometime occur the fast discharge velocity. In this study, the seepage model test performed to evaluate seepage behavior with tidal variation of final closure and continuous sea dyke section such as discharge velocity, hydraulic gradient, and phreatic line. Based on the seepage model test results, the maximum discharge velocity of final closure section is 1.7m/sec. Also the local discharge velocity increment and vortex is occurred.

• 대한조선학회논문집
• /
• 제48권5호
• /
• pp.390-395
• /
• 2011

The main purpose of ice model basin is to assess and evaluate the performance of the Arctic ships and offshore structures because the full-scale tests in ice covered sea are usually very expensive and difficult. There are various ice conditions, such as level ice, brash ice, pack ice and ice ridge, in the real sea. To estimate their capacities in ice tank accurately, an appropriate model ice sheet and prepared ice conditions copied from actual sea ice conditions are needed. Pack ice is a floating ice that has been driven together into a single mass and a mixture of ice fragments of varying size and age that are squeezed together and cover the sea surface with little or no open water. So Ice-class vessels and Icebreaker are usually operated in pack ice conditions for the long time of her voyage. The most ice model tests include the pack ice test with the change of pack ice concentration. In this paper, the effect of pack ice size and channel breadth in pack ice model test is conducted and analyzed. Also we presented some techniques for the calculation of pack ice concentration in the model test. Finally, we developed a new model test methodology of pack ice condition in square type ice tank.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 대한조선학회논문집
• /
• 제48권1호
• /
• pp.8-14
• /
• 2011

RIB(Rigid Inflatable Boat) is widely used for coastal transportation in the commercial use and for ISR(Intelligence, Surveillance, Reconnaissance) in the military use. Since RIB is around 10 meters in length and over 30 knots in speed, its motion characteristics in waves is quite different from a large scale ship. When it turns, large roll occurs and heeling direction is opposite to the large ship's case. Currently, many countries are developing USV(Unmanned Surface Vehicle) of which type is RIB. In order to develop high performance autopilot and way point controller, it is very important to identify RIB's motion characteristics. In this paper, sea trial test results of a 7-meter RIB such as speed, turning, zig-zag, and way point control tests were represented and its resistance and propulsion model was identified by using sea trial data and Savitsky's formula. In addition, the state space model which will be used in the identification of the four-degree-of-freedom dynamics in the next step was formulated and the identification procedure was proposed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.953-956
• /
• 2005

The vibroacoustic analysis has been carried out on the RazakSAT qualification model which was developed by SI and ATSB. Statistical energy analysis was used for the analysis and the results was compared with acoustic test results. The equipments of the RazakSAT are simplified as uniformly distributed mass on the panels in the SEA model. According to the comparison of the analysis and test results, SEA is useful estimation of the response in high frequency region and the results are valid when the assumption of equipartition of modal energy is agreed.

• 대한조선학회논문집
• /
• 제42권2호
• /
• pp.105-112
• /
• 2005

IMO standards for ship manoeuvrability were applied from January 1, 2004. Though model test or sea trial in full load condition is needed, it is not always possible to get such data for every ships. Therefore it is required to study the effect of loading conditions on ship manoeuvrability. Approximate formulae to estimate the hydrodynamic forces acting on a ship and the 2nd overshoot angle of $10^{\circ}$/$10^{\circ}$ zig-zag test in certain loading condition are proposed in this study These were derived from the results of model test and sea trial data. Captive model tests for 7 ships with 15 different loading conditions and sea trial data including free running test of 6 cases were used. Compared with experiment data and prediction formulae already proposed by others, the approximate formulae in this study show good agreement with model test results.

• 한국지반신소재학회논문집
• /
• 제5권1호
• /
• pp.25-32
• /
• 2006

방조제 공사는 바다를 막아 바닷물의 흐름을 차단해가는 과정으로 육상공사와는 달리 수심이 깊고 파랑이 심한 바다에서 이루어지는 공사이기 때문에 축조재료의 유실이 많고 심할 경우 방조제가 붕괴되는 위험이 큰 공사이다. 특히, 방조제의 끝막이 단면은 대규모 사석과 돌망태 등을 이용하여 시공하므로, 구성 재료가 불규칙하고 간극이 크기 때문에 일반적인 지반내의 침투흐름보다 상당히 빠른 침투가 발생된다. 본 연구에서는 방조제 끝막이 후 축조된 사석단면과 후속공정을 통하여 축조되는 방조제단면에 대한 실내 침투모형시험을 수행하여 침투거동을 예측 및 분석하였다. 다양한 조위변화를 재현하여 근고공 필터매트 시공에 따른 사석단면내의 유속변화, 침윤선 분포 등을 계측하여 침투거동을 분석하였다. 실내 침투모형시험 결과, 끝막이 사석단면의 침투유속은 최대 1.7m/sec 발생하였으며, 근고공 필터매트 시공에 따라 최대 침투유속이 23.7% 감소하였다.