• Journal of the East Asian Society of Dietary Life
• /
• v.2 no.2
• /
• pp.277-282
• /
• 1992

This study was designedto investigate changes in phsicochemical properties of rice extrudate with added glycerin fatty acid ester extruded by single screw extruder. According to emulsifier content, expansion ratio and water solubility index were represented minimum in rice extrudate with added 2.0% and 2.5% glycerin fatty acid ester. Extrudate with added 1.5% emulsifier revealed lowest break strength and bulk density, so got a tender and light texture. Meanwhile water absorption index was showed maximum at 1.5% emulsifier content. As emulsifier content increased, lightness raised. By the microstructure obsorved with image analyzer, addition of emulsifier had decreased area and fractarea of air cells of cross section of extrudates. On the results of this research, quality of extrudate with added 1.5% glycerin fatty acid ester was considered very well than 100% rice extrudate, because of tender and light texture, highest water absorption indexand fine structure with higher lightness.

• Elastomers and Composites
• /
• v.55 no.1
• /
• pp.1-5
• /
• 2020

This study examined the effects of the addition of maleic anhydride-grafted polypropylene (PP-g-MA) and polyolefin elastomer (POE) on polyamide 66 (PA66) and polypropylene (PP) blends. The blends of PA66/PP with PP-g-MA and POE were prepared using a twin screw extruder. Mechanical testing results revealed that the tensile, flexural, and izod impact strengths of the blends were maximized at a PP-g-MA content of 2 phr. The increased mechanical strength of the blends with PP-g-MA was attributed to the compatibilizing effect of the PA66 and PP blends. In addition, as the POE content increased, the impact strength of the blends increased. However, at a high POE content, the tensile and flexural strengths decreased, seemingly because of the lower mechanical properties of POE.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.107-111
• /
• 2011

Polypropylene(PP)/carbon fiber(CF)/multi-walled carbon nanotube(MWCNT) nanocomposites along with various CF and MWCNT contents were prepared in a Twin screw extruder. Electrical, mechanical property and morphology were investigated with a variation of CF and MWCNT contents. From the surface resistance of PP/CF/MWCNT composites, MWCNT can increase the conductivity of composites compared with PP/CF composites without MWCNT. It is suggested that MWCNT and CF can make the conductive network in the polymer matrix. Flexural modulus and Izod impact strength of the PP/CF/MWCNT composites were improved with the increase of CF contents. Morphology showed that length of CF in polymer matrix was shortened by torque during melt mixing with MWCNT. As a result of this phenomenon, the impact strength of composites was somewhat decreased.

• Journal of the East Asian Society of Dietary Life
• /
• v.17 no.3
• /
• pp.379-383
• /
• 2007

The effects of phenolic acids on the physical properties of wheat flour extrudate were investigated. Ferulic acid, fumaric acid, and p-coumaric acid were mixed with hard wheat flour, respectively, and extruded under a twin screw extruder. We found that by adding the phenolic acids, longitudinal expansion at the die increased, textural hardness decreased, and the water absorption capacity of the extrudate decreased. The results showed that the addition of phenolic acids produced a softer textured, more longitudinally puffed and hydrophobic extrudate compared to the control extrudate. Moreover, the addition of phenolic acids did not significantly affect the color of the extrudate: oxidative browning of the phenolic acids was not observed, due to inactivation of the browning enzymes under the hot temperature and reduced oxygen conditions of the extrusion process.

• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.113-120
• /
• 2013

The melt intercalation to commercialize nanocomposites in a pilot scale was applied and the water absorption characteristics for polyamide/MMT nanocomposites manufactured by twin screw extruder was studied. As a result, water absorption decreased with the introduction of MMT and dimensional stability was improved. However, as water absorption increased, flexural strength and modulus were reduced. Therefore, the effect of MMT introduction on mechanical properties of nanocomposites was clearly observed, which may increase the level of strength by maintaining anti-water absorption property of nanocomposite.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.5
• /
• pp.420-425
• /
• 2000

Crosslinked polyethlyene/silane crosslinked polyethylene(XLPE/SXLPE) blends were prepared by a twin screw extruder and their water tree growing electrical breakdown and crossinking characteristics were investigated. The water tree characteristics of XLPE were improved by the addition of SXLPE when samples were crosslinked only by the thermorolysis of DCP (dicumyl peroxide). However steam curing process was not good for water tree characteristics. It was also found that the rate of water tree growing of XLPE/SXLPE blend increased when the content of SXLPE was 50%. AC breadown strength slightly increaed by the addition of SXLPE to XLPE when samples were crosslinked only by the thermorolysis of DCP. It was also found that the degree of crosslinking of XLPE/SXLPE blends were higher than that of XLPE in the case of the content without steam crosslinking process.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.493-494
• /
• 2006

Chip breaker of cutting tool is an important feature to enhance cutting performance. Powder injection molding process was used to produce a triangular-shape cermet grooving insert which has three chip breakers. Attrition milled cermet powders were mixed with wax-based binder system in continuous twin screw extruder. Three-plate injection mold with slide cores was used to produce injection-molded parts. After molding, solvent and thermal debinding was carried out. Sintering was conducted in a batch furnace with a graphite heater. The sintered parts satisfy the requirements of dimensional tolerances and material properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.55-58
• /
• 1999

Crosslinked polyethylene/silane crosslinked polyethylene (XLPE/SXLPE) blends were prepared by a twin screw extruder and their water tree growing and electrical breakdown characteristics of XLPE were improved by the addition of SXLPE, when samples were crosslinked only by the thermorolysis of DCP (dicumyl perosxide). However, steam curing process was not good for water tree characteristics. It was also found that the rate of water tree growing of XLPE/SXLPE blend increased when the content of SXLPE was 50 %. AC breadown strength slightly increased by the addition of SXLPE to XLPE when samples were crosslinked only by the thermorolysis of DCP.

• The Korean Journal of Rheology
• /
• v.10 no.2
• /
• pp.57-64
• /
• 1998

A pultrusion resin impregnation (PRI) die, which has been developed recently in our laboratory, was used to pre-pare various composite system. The continuous fiber reinforced composites of glass fiber/polypropylene(GFPP) and glass fiber/polyamide 6 (GFPA) were first manufactured by means of the PRI die and then cut into chopped pellets of predet-ermined length. These pellets and either virgin or modified thermoplastic resin were melt-mixed by a twin screw extruder to prepare GF/PA/PP and GF/PA/PPMA system. The mechanical properties of these blends were investigated and discussed in terms of their morphological observations. These preliminary results revealed that this new impregnation die could be suc-cessfully applied to produce prepregs suitavle for the final shaping process.

• Journal of the Korean Society of Industry Convergence
• /
• v.13 no.2
• /
• pp.93-98
• /
• 2010

Polypropylene / montmorillonite / wood flour nanocomposites are melt-mixed by using a twin screw extruder. The montmorillonite is intercalated by the wood flour and the basal spacing of montmorillonite is increased with increasing the content of wood flour. The exfoliation constantly occurs by adding more than 10 wt.% of maleic anhydride-grafted polypropylene as the compatibilizer, which is used for improving the interfacial adhesion between matrix and filler. Also, the maleic anhydride-grafted polypropylene enhances the mechanical properties of the nanocomposites.