• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.223-224
• /
• 2008

Important element are low cost, high-efficiency crystalline silicon solar cells. in this paper, Will be able to contribute in low cost, high-efficiency silicon solar cells, Applies oxide/nitride passivation, produced screen-printed solar cells. and the Measures efficiency, and evaluated a justice quality oxide/nitride passivation screen-printed solar cells.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.896-898
• /
• 2009

The printed electrodes of organic thin-film transistors (OTFTs) were fabricated by screen printing using nanoparticle silver pastes. The screen printed OTFT corresponds to channel lengths between 7.6 to 82.6 ${\mu}m$ (designed L=10 to 80 ${\mu}m$) on the $150{\times}150mm^2$ paper. The channel length deviations for 40 to 80 ${\mu}m$ patterns were less than 5 %. However, the channel lengths for 10 to 30 ${\mu}m$ patterns were increased by 20 %. The screen printed bis(triisopropyl-silylethynyl) pentacene (TIPS-pentacene) OTFTs obtained had a field-effect mobility as large as 0.08 (${\pm}0.02$) $cm^2$/Vs, an on/off current ratio of $10^5$ and a subthreshold slope of 1.95 V/decade.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.629-632
• /
• 2008

Printed organic thin-film transistors (OTFTs) were used in the fabrication of a screen- printed gate, source and drain electrodes on flexible plastic substrates using silver pastes, a coated polyvinylphenol dielectrics, and jetted bis(triisopropyl-silylethynyl) pentacene (TIPS-pentacene) organic semiconductor. The OTFTs printed using screen printing and soluble processes made it was possible to fabricate a printed OTFT with a channel length as small as $13\;{\mu}m$ on plastic substrates; this was not possible using previous traditional printing techniques.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.217-223
• /
• 2016

In this research, a continuous roll-to-roll screen printing system was developed using a flat screen. It has a newly devised sliding mechanism of screen printing module, which can be controlled accurately in sync with a moving web, driven by a roll-to-roll tension control and web-guiding system. In addition, the real-time precision alignment module that consists of a vision camera and an $X-Y-{\theta}$ alignment stage was implemented. With this developed system, the feasibility of continuous printing with minimum pattern width below $60{\mu}m$ was verified, and an overlay of ${\pm}60{\mu}m$ between the laser-patterned reference mark and the printed mark on a 300-mm-wide film was achieved.

• 한국인쇄학회지
• /
• 제19권2호
• /
• pp.49-57
• /
• 2001

This thesis attempts to study ink transition for on the polycarbonate multicalculator plate for automobile. For this study, the change of weight by screen printed ink transition on polycarbonate material by ink viscosity(be diluted ; 0%, 5%, 10%, 20%) was observed. The weight by screen printed ink is depended on amount of added solvent. We have studied change of the weight by the transition of the ink that was screen-printed on polycarbonate which is to be printed according to the viscosity of the ink (diluent: undiluted solution 5%, 10%, 15%, 20%). This shows that ink transition become activated since the amount of ink(or/and the viscosity of ink) is increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1990년도 추계학술대회 논문집
• /
• pp.26-30
• /
• 1990

Bi$\_$0.7/Pb$\_$0.3/Sr$_1$Ca$_1$Cu$\_$1.8/Ox thick films were screen printed on magnesia(MgO), silver and yttrium stabilized zirconia (YSZ) substrates and were sintered in a boat with cover to prevent the evaporation. The high-Tc phase increase and the low-Tc phase and Ca$_2$PbO$_4$ decrease with an increase in sintering temperature from 835$^{\circ}C$ to 860$^{\circ}C$. YSZ substrate interact strongly with the oxide resulting in poor superconductor, while the Ag and MgO substrates were satisfactory to make screen printed superconductors. The Bi$\_$0.7/Pb$\_$0.3/Sr$_1$Ca$_1$Cu$\_$1.8/Ox thick films screen printed both on Ag and MgO substrates show high Tc phase of ~85% and Tc of 96K.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.4.1-4.1
• /
• 2011

Recently, circuit printing technology has been considered as a promising alternative to conventional PCB fabrication, for it can greatly reduce the manufacturing costs. Even though printed circuit has many advantages over typical subtractive technology such as fewer processes, it has some disadvantages. The major problems are low adhesion and poor resolution. Efforts to overcome these problems have been mainly focused on ink developments with a limited success. And surface treatments showed some improvements. Therefore, various plasma treatments and primer coatings on plastic substrates have been tested. Plasma treatments using hydrocarbon gases including methane and propane improved the pattern quality of the inkjet printed circuit, which are further improved upon heating of substrate. On the other hand, there is little effect on the adhesion, which is improved only by a special primer coating. The adhesion of inkjet printed circuit has been increased more than 10 times upon treatment. As for the screen printed circuits, the overall effects are less significant since there is some organic binder in the ink. Nonetheless, the treatment has strong positive effects on pattern quality and adhesion. The adhesion of 1 kgf/cm2, which is comparable with those of the conventional PCB circuits, is possible through primer coating for both screen and inkjet printed circuits. The resulting circuit also showed good thermal, mechanical and electrical properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.380-383
• /
• 2007

In this research, we present color filter which is patterned by screen printing method. Analysis of screen printing process, screen printing system, experiment for uniform printing in large area, characteristics of screen printed CF are investigated .In spite of limitation of precision, screen printed color filter is very cost- effective in respect of manufacturing facility and ink usage.

• 한국재료학회지
• /
• 제27권8호
• /
• pp.397-402
• /
• 2017

We used an etching process to control the line-width of screen printed Ag paste patterns. Ag paste was printed on anodized Al substrate to produce a high power LED. In general, Ag paste spreads or diffuses on anodized Al substrate in the process of screen printing; therefore, the line-width of the printed Ag paste pattern increases in contrast with the ideal line-width of the pattern. Smudges of Ag paste on anodized Al substrate were removed by neutral etching process without surface damage of the anodized Al substrate. Accordingly, the line-width of the printed Ag paste pattern was controlled as close as possible to the ideal line-width. When the etched Ag paste pattern was used as a seed layer for electroless Ni plating, the line width of the plated Ni film was similar to the line-width of the etched Ag paste pattern. Finally, in pattern formation by Ag paste screen printing, we found that the accuracy of the line-width of the pattern can be effectively improved by using an etching process before electroless Ni plating.

• 한국정밀공학회지
• /
• 제17권2호
• /
• pp.130-136
• /
• 2000

Generally, the build-up printed circuit board manufactured by the sequential process with etching, plating, drilling etc. requires many types of equipments and lead time. Etching process is suitable for mass production, however, it is not adequate for manufacturing prototype in the developing stage. In this study, we introduce a screen printing technology to prototyping a build-up printed circuit board. As for the material, photo/thermal curable resin and conductive paste are used for the formation of dielectric and conductor. The build-up structure is made by subsequent processes such as the formation of liquid resin thin layer, the solidification by UV/IR light, and via filling with conductive paste. By use of photo curable resin, productivity is greatly enhanced compared with thermal curable resin. Finally, the basic concept and the possibility of build-up printed circuit board prototyping are proposed in comparison with to the conventional process.