• 한국전기전자재료학회논문지
• /
• 제21권1호
• /
• pp.29-34
• /
• 2008

In this paper, we investigated electrical and physical characteristics of nickel silicide using rare-earth metals(Er, Yb, Tb, Dy), Incorporated Ytterbium into Ni-silicide is proposed to reduce work function of Ni-silicide for nickel silicided schottky barrier diode (Ni-silicided SBD). Nickel silicide makes ohmic-contact or low schottky barrier height with p-type silicon because of similar work function (${\phi}_M$) in comparison with p-type silicon. However, high schottky barrier height is formed between Ni-silicide and p-type substrate by depositing thin ytterbium layer prior to Ni deposition. Even though the ytterbium is deposited below nickel, ternary phase $Yb_xN_{1-x}iSi$ is formed at the top and inner region of Ni-silicide, which is believed to result in reduction of work function about 0.15 - 0.38 eV.

• 센서학회지
• /
• 제31권4호
• /
• pp.271-277
• /
• 2022

We analyzed the effects of the interface trap on the output characteristics of an inversion mode n-channel GaN Schottky barrier (SB)-MOSFET based on the N_it distribution using TCAD simulation. As interface trap number density (N_it) increased, the threshold voltage increased while the drain current density decreased. Under N_it=5.0×10¹⁰ cm^-2 condition, the threshold voltage was 3.2 V for V_DS=1 V, and the drain current density reduced to 2.4 mA/mm relative to the non-trap condition. Regardless of the N_it distribution type, there was an increase in the subthreshold swing (SS) following an increase in N_it. Under U-shaped N_it distribution, it was confirmed that the SS varied depending on the gate voltage. The interface fixed charge (Q_f) caused an shift in the threshold voltage and increased the off-state current collectively with the surface trap. In summary, GaN SB-MOSFET can be a building block for high power UV optoelectronic circuit provided the surface state is significantly reduced.

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.877-882
• /
• 2005

In order to fabricate a high breakdown SiC-SBD (Schottky barrier diode), we investigate an effect on metal guard ring (MGR) in breakdown characteristics of the SiC-SBD. The breakdown characteristics of MGR-type SiC-SBD is significantly dependent on both the guard ring metal and the alloying time of guard ring metal. The breakdown characteristics of MGR-type SiC-SBDs are essentially improved as the alloying time of guard ring metal is increased. The SiC-SBD without MGR shows less than 200 V breakdown voltage, while the SiC-SBD with Al MGR shows approximately 700 V breakdown voltage. The improvement in breakdown characteristics is attributed to the field edge termination effect by the MGR, which is similar to an implanted guard ring-type SiC-SBD. There are two breakdown origins in the MGR-type SiC-SBD. One is due to a crystal defects, such as micropipes and stacking faults, in the Epi-layers and the SiC substrate, and occurs at a lower electric field. The other is due to the destruction of guard ring metal, which occurs at a higher electric field. The demolition of guard ring metal is due to the electric field concentration at an edge of Schottky contact metal.

• Transactions on Electrical and Electronic Materials
• /
• 제16권5호
• /
• pp.285-289
• /
• 2015

We prepared silver Schottky contacts to O-polar and nonpolar m-plane bulk ZnO wafers. Then, by considering various transport models, we performed a comparative analysis of the current transport properties of Ag/bulk ZnO Schottky diodes, which were measured at 300, 200, and 100 K. The fitting of the forward bias current-voltage (I-V) characteristics revealed that the tunneling current is dominant as the transport component in both the samples. Compared to thermionic emission (TE), a stronger contribution of tunneling current was observed at low temperature. The reverse bias I-V characteristics were well fitted with the thermionic field emission (TFE) in both the samples. The presence of acceptor-like adsorbates, such as O₂ and H₂O, modulated the surface conductive state of ZnO, thereby affecting the tunneling effect. The degree of activation/passivation of acceptor-like adsorbates might be different in both the samples owing to their different surface morphologies and surface defects (e.g., oxygen vacancies).

• 반도체디스플레이기술학회지
• /
• 제16권1호
• /
• pp.70-74
• /
• 2017

To research the electrical properties of ZnS thin films with various annealing conditions, ZnS was prepared by RF magnetron sputtering system and annealed in a vacuum for 10 minutes. All films were analyzed by the XRD, PL and I-V measurement system. The XRD pattern of ZnS film annealed at $100^{\circ}C$ was shifted to lower 2 theta because of the formation of a depletion region at the interface between a substrate and ZnS thin film, and the capacitance was abruptly increased. However, the pattern of XRD of ZnS film annealed at $100^{\circ}C$ with a Schottky contact was showed the amorphous structure, and the current-voltage characteristics were non-linearly observed by the Schottky contact.

• 한국전기전자재료학회논문지
• /
• 제27권4호
• /
• pp.199-202
• /
• 2014

The effect of neutron irradiation on the properties of SiC Schottky Diode has been investigated. SiC Schottky diodes were irradiated under neutron fluences and compared to the reference samples to study the radiation-induced changes in device properties. The condition of neutron irradiation was $3.1{\times}10^{10}$ $n/cm^2$. The current density after irradiation decreased from 12.7 to 0.75 $A/cm^2$. Also, a slight positive shift (${\Delta}V_{th}$= 0.15 V) in threshold voltage from 0.53 to 0.68 V and a positive change (${\Delta}{\Phi}_B$= 0.16 eV) of barrier height from 0.89 to 1.05 eV have been observed by the neutron irradiation, which is attributed to charge damage in the interface between the metal and the SiC layer.

• 한국전기전자재료학회논문지
• /
• 제23권10호
• /
• pp.763-766
• /
• 2010

By improving the conducting process of metal source/drain (S/D) in direct contact with the channel, schottky barrier metal-oxide-semiconductor field effect transistors (SB MOSFETs) reveal low extrinsic parasitic resistances, offer easy processing and allow for well-defined device geometries down to the smallest dimensions. In this work, we investigated the arrhenius plots of the SB MOSFETs with different S/D schottky barrier (SB) heights between simulated and experimental current-voltage characteristics. We fabricated SB MOSFETs using difference S/D metals such as Cr (${\Phi}_{Cr}$ ~4.5 eV) and Ni (${\Phi}_{Ni}$~5.2 eV), respectively. Schottky barrier height (${\Phi}_B$) of the fabricated devices were measured to be 0.25~0.31 eV (Cr-S/D device) and 0.16~0.18 eV (Ni-S/D device), respectively in the temperature range of 300 K and 475 K. The experimental results have been compared with 2-dimensional simulations, which allowed bandgap diagram analysis.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.471-476
• /
• 2003

Au/oxide/n-InP Schottky diodes were fabricated from heteroepitaxial InP layers grown on GaAs substrates by the metalorganic vapor phase epitaxy (MOVPE) method from a new combination of source materials: ethyldimethylindium (EDMIn) and tertiarybutylphosphine (TBP). Anodic oxidation technique by using a solution of 10 g of ammonium pentaborate in 100 cc of ethylene glycole as the electrolyte was used to deposit a thin oxide layer. The barrier heights determined from three different techniques, current-voltage (I-V) measurements at room temperature and in the temperature range of 273 K - 373 K, and room temperature capacitance-voltage (C-V) measurements are in good agreement, 0.7 - 0.9 eV which is considerably high as compared to the 0.45 - 0.55 eV in Au/n-InP Schottky diode without a Passivation layer. The ideality factors of 1.1 - 1.3 of the Schottky diodes were also determined from the I-Y characteristics. Deep level transient spectroscopy (DLTS) studies revealed only one shallow electron state at 92.6 meV below the bottom of the conduction band and no deep state in the heteroepitaxial InP layers grown from EDMIn and TBP.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권7호
• /
• pp.388-393
• /
• 2000

Hydrogen-sensing behaviors of Pd- and Pt-SiC Schottky diodes, fabricated on the same SiC substrate, have been systematically compared and analyzed as a function of hydrogen concentration and temperature by I-V and$\DeltaI-t$ methods under steady-state and transient conditions. The effects of hydrogen adsorption on the device parameters such as the barrier height are investigated. The significant differences in their hydrogen sensing characteristics have been examined in terms of sensitivity limit, linearity of response, response rate, and response time. For the investigated temperature range, Pd-SiC Schottky diode shows better performance for H2 detection than Pt-SiC Schottky diode under the same testing conditions. The physical and chemical mechanisms responsible for hydrogen detection are discussed. Analysis of the steady-state reaction kinetics using I-V method confirmed that the atomistic hydrogen process is responsible for the barrier height change in the diodes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.350-353
• /
• 2002

High voltage SiC Schottky barrier diodes with field plate structure have been fabricated and characterized. N-type 4H-SiC wafer with an epilayer of ∼10$\^$15/㎤ doping level was used as a starting material. Various Schottky metals such as Ni, Pt, Ta, Ti were sputtered and thermally-evaporated on the low-doped epilayer. Ohmic contact was formed at the backside of the SiC wafer by annealing at 950$^{\circ}C$ for 90 sec in argon using rapid thermal annealer. Field oxide of 550${\AA}$ in thickness was formed by a wet oxidation process at l150$^{\circ}C$ for 3h and subsequently heat-treated at l150$^{\circ}C$ for 30 min in argon for improving oxide quality. The turn-on voltages of the Ni/4H-SiC Schottky diode was 1.6V which was much higher than those of Pt(1.0V), Ta(0.7V) and Ti(0.7). The voltage drop was measured at the current density of 100A/$\textrm{cm}^2$ showing 2.1V for Ni Schottky diode, 1.45V for Pt 1.35V, for Ta, and 1.25V for Ti, respectively. The maximum reverse breakdown voltage was measured 1100V in the file plated Schottky diodes with 101an thick epilayer.