• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.1546-1549
• /
• 2007

A ride quality measurement was carried out for commuter and express train used in airport railway. Lateral and vertical directional average ride quality level is higher than that of longitudinal direction. Because express train is faster than commuter train, the average ride quality level of express train is higher compared to that of commuter train. The average ride quality level of commuter train is between 'good comfortable($100{\sim}105dB$)' and 'very good comfortable(below 100dB)'. The average ride quality level of express train is between 'not comfortable($105{\sim}110dB$)' and 'good comfortable($100{\sim}105dB$)'. In spite of the scheduled speed is higher(more than 70km/h for commuter train, more than 80km/h for express train) than other lines, the ride quality of airport railway train is good. The reason is that there is little gradient in rail and the radius of curvature is larger compared to that of other lines.

• Journal of Satellite, Information and Communications
• /
• v.3 no.2
• /
• pp.43-47
• /
• 2008

COMS is the one of Korean hybrid geostationary satellite and is scheduled to be launched in 2009 by Arian V into $128^{\circ}$ E longitude. COMS is designed and manufactured for three main objectives which are Communications, Oceanographic, and Meteorological missions. It provides the weather monitoring, ocean monitoring, and Ka band satellite communication services by means of three different payloads. The Ka band communications payload was developed by Electronics and Telecommunications Research Institute (ETRI), and provides not only the digital transmission for the communication services against natural disaster but also digital transmission for the high speed multimedia services. This paper describes the overview of the electrical and mechanical design and measured performances of the Ka band communications transponder flight model (FM) for COMS.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.2
• /
• pp.238-246
• /
• 2008

This case study refers to turbine-generator with retrofitted turbine rotor. Vibration problem occurring after the retrofit was mainly due to high vibration from exciter side. However, repeated test run and operation during scheduled maintenance caused high vibration from generator bearing, and post-overhaul test run before turbine vibration correction caused oil whip on the bearing. This case study shows how to analyze vibration condition of high turbine generator vibration detected during the post-overhaul test run and vibration condition of offline and online data to reflect it on establishing maintenance schedule and overhaul correction procedure. Vibration data could be acquired during steady load operation or even with varying speed and load. Each data is important for machinery condition evaluation. This case study shows that the vibration data during extreme condition is the key factor in analysis, which helps to find the machinery problem.

• Journal of Internet Computing and Services
• /
• v.10 no.4
• /
• pp.213-222
• /
• 2009

IEEE 802.15.3 HR-WPAN is designed to enable wireless connectivity of high-speed, low-power, low-cost multimedia-capable portable consumer electronic devices. For quality of service, the standard specifies the use of TDMA (Time Division Multiple Access). However, during low contention TDMA gives much lower channel utilization and higher delays than CSMA (Carrier Sensing Multiple Access) because in TDMA, a node can transmit only during its scheduled time slots whereas in CSMA, nodes can transmit at any time as long as there is no contention. By mixing CSMA and TDMA, Hybrid MAC becomes more robust to timing failures, time-varying channel conditions, slot assignment failures and topology changes than a stand-alone TDMA.

• Journal of the Korean Society for Railway
• /
• v.13 no.3
• /
• pp.333-338
• /
• 2010

Investment in railroad, it is very important to find a way to increase a benefit to make the economic efficiency more positive, but is also considering that the cost will be higher. In this paper, we suggest a optimized model for increasing the benefit of railroad business considering of stopping patterns. According to existing analytical method, the operation hour is calculated based on that scenario regarding that it stops at all major stations but it does not fit the actual operation conditions. Considering various stopping patterns can be reasonably calculated the cost for required rail cars in the planning stages, and can also affect economic efficiency in a positive way.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.812-817
• /
• 2004

Recently drastic improvement of railway technology has been accompanied by the construction of very high-speed tracks. It should be noticed that Continuously Welded Rail(CWR) has played significant role in technical development of railway and that installation of CWR is now being scheduled on existing lines as well as newly-built lines. In general, interaction between CWR and bridge deck takes place on bridge section and additional axial force and displacement is to be developed owing to temperature and braking/acceleration forces. This interaction is known to be mainly governed by span organizations and arrangements of foot bearings. In common practice, movable bearing is stationed and designed on the assumption that it is not able to transfer the horizontal force of upper decks. However, it is well known that horizontal resistance is developed in movable bearings due to friction and that friction coefficient of movable bearing is ranged from 0.03 to 0.20 depending on the material of bearings and magnitude of reactions. Therefore, it is easily reasoned out that friction of movable bearing can influence the mutual behavior of CWR and bridge decks. Suggested in this study is to investigate the validity and efficiency of friction effect of movable bearings in controlling the axial force and displacement of CWR on continuous railway bridges.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.811-820
• /
• 2006

The Platform Screen Door system(PSD) is scheduled to be installed on the platform of some subway stations in Seoul, Pusan, Kwang-Ju, Daejun and Daegu and all stations of Seoul Subway No 9. will equipped with PSD. On the other hand Seoul Metropolitan Rapid Speed(SMRT) that has operated the train automatically had finished the basic desic design and the execution drawing of PSD and installed successfully the PSD on the platforms in the Kimpo Airport station in Subway Line No 5. at dec. 2005. The exhibition operations of PSD has made the major contribution to build up the safe and optimum subway for the increasing customers. Nowadays PSD has operated on ATO sections and ATS sections. But in the case of closing the door manually in ATO sections, it would be delayed about 5 seconds in closing the door of PSD. Although the interface of PSD, train and the signal system is established automatically, we have to supplement technically on the interface between train, PSD and the ground signal interface equipments. Therefore I will center on the optimizing methods about the interfacing system between the train and the PSD, train and the signal system to overcome the above problems in this study.

• Journal of KIISE:Computer Systems and Theory
• /
• v.35 no.9_10
• /
• pp.417-420
• /
• 2008

We consider the problem of optimizing the performance of a system shared by selfish non-cooperative users. In this problem, small jobs which the users request should be scheduled on a set of shared machines with their speed functions, each of which dependson the amount of jobs allocated on a machine. The performance of the system is measured by the maximum of the completion times when the machines complete the jobs allocated on them. The selfish users can choose a machine on which their jobs are executed, and they choose the fastest machine. But it typically results in suboptimal system performance. The Price of Anarchy(PoA) was introduced as a measure of the performance degradation due to the user's selfish behavior. The PoA is the worst-case ratio of the cost of a Nash equilibrium to the optimal cost. In this paper, we estimate the PoA for the above scheduling problem.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.9A
• /
• pp.663-668
• /
• 2003

With the advent of high speed networking technology, computers connected to the high-speed networks tend to consume more of their CPU cycles to process data. So one of the solutions to improve the performance of the computers is to reduce the CPU cycles for processing the data. As the consumption of the CPU cycles is increased in proportion to the number of the packets per second to be processed, reducing the number of the packets per second by increasing the length of the packet is one of the solutions. In order to meet this requirement, two types of jumbo packets such as jumbograms and jumbo frames have already been standardized or being discussed. In case that the jumbograms and general packets are interleaved and scheduled together in a router, the jumbogrms may deteriorate the QoS of the general packets due to the transfer delay. They also frequently exhaust the memory with storing the huge length of the packets. This produces the congestion state easily in the router that results in the loss of the packets. In this paper, we analyze the problems in processing the jumbo packets and suggest a noble solution to overcome the problems.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.3
• /
• pp.115-118
• /
• 2011

Process characterization of the chemical mechanical polishing (CMP) process for undensified phosphosilicate glass (PSG) film is reported using design of experiments (DOE). DOE has been addressed to experimenters to understand the relationship between input variables and responses of interest in a simple and efficient way. It is typically beneficial for determining the adequate size of experiments with multiple process variables and making statistical inferences for the responses of interests. Equipment controllable parameters to operate the machine include the down force (DF) of the wafer carrier, pressure on the backside of the wafer, table and spindle speed (SS), slurry flow rate, and pad condition. None of them is independent; thus, the interaction between parameters also needs to be indicated to improve process characterization in CMP. In this paper, we have selected the five controllable equipment parameters, such as DF, back pressure (BP), table speed (TS), SS, and slurry flow (SF), most process engineers recommend to characterize the CMP process with respect to material removal rate (RR) and film uniformity as a percentage. The polished material is undensified PSG. PSG is widely used for the plananization in multi-layered metal interconnects. We identify the main effect of DF, BP, and TS on both RR and film uniformity, as expected, by the statistical modeling and analysis on the metrology data acquired from a series of $2^{5-1}$ fractional factorial design with two center points. This revealed the film uniformity of the polished PSG film contains two and three-way interactions. Therefore, one can easily infer that the process control based on better understanding of the process is the key to success in semiconductor manufacturing, typically when the wafer size reaches 300 mm and is continuously scheduled to expand up to 450 mm in or little after 2012.