• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.161-164
• /
• 1996

The authors have recently proposed a new method for identifying Volterra kernels of nonlinear control systems by use of M-sequence and correlation technique. A specially chosen M-sequence is added to the nonlinear system to be identified, and the crosscorrelation function between the input and output is calculated. Then every crosssection of Volterra kernels up to 3rd order appears at a specified delay time point in the crosscorrelation. This method is applied to a saturation-type nonlinear feedback control system of mechanical-electrical servo system having torque saturation nonlinearity. Simulation experiments show that we can obtain Volterra kernels of saturation-type nonlinear system, and a good agreement is observed between the observed output and the calculated one from the measured Volterra kernels.

• 전기학회논문지
• /
• 제56권1호
• /
• pp.66-70
• /
• 2007

For the design to prevent the saturation of the iron core and the effective fault current limitation, the analysis for the operation of the flux-lock type superconducting fault current limiter (SFCL) with consideration for the hysteresis characteristics of the iron core is required. In this paper, the hysteresis characteristics of the flux-lock reactor, which is an essential component of the flux-lock type SFCL, were investigated. Under normal condition, the hysteresis loss of the iron core in the flux-lock type SFCL does not happen due to its winding structure. From the equivalent circuit for the flux-lock type SFCL and the fault current limiting experiments, the hysteresis curves could be drawn. From the analysis for both the hysteresis curves and the fault current limiting characteristics due to the number of turns for the 1st and 2nd windings, the increase of the number of turns in the 2nd winding of the flux-lock type SFCL had a role to prevent the iron core from saturation.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권2호
• /
• pp.116-122
• /
• 2000

In the high speed range for salient type synchronous reluctance motor, the effect of iron loss can not be negligible. We have investigated the voltage equations including iron loss from the model that is added the equivalent iron loss in the equivalent inductance in series. In this paper, we derive Ld linear approximate equation from saturation range of Ld, Lq vs applied voltage characteristics and obtain equations including saturation and iron loss related to maximum torque control using Ld. The effect of saturation and iron loss is investigated under maximum torque control. And we show that the proposed maximum torque control scheme achieves the desired performances through experimental results.

• 한국염색가공학회지
• /
• 제12권6호
• /
• pp.344-352
• /
• 2000

Two kinds of nylon 6 fabrics with different fiber denier, such as ultramicro fiber(UMF) nonwoven fabric(monodenier 0.05d) and regular fabric(monodenier 2.92d) are dyed with C.I. Acid Red 18(leveling type) and C.I. Acid Blue 113(milling type). Dyeing rates and adsorption isotherms are measured at $60^\circ{C}$, pH 5.0 and at liquor ratio of 1 : 250. To investigate the effect of fixing agents (Matexil FA-SNX, Monorex-RD and Tinofix-ECO) on UMF nylon 6 nonwoven fabric, dyeing is carried out at 3~10% owf with 1 : 2 metal-complex acid dyes, such as Kayalax Navy R(unsulphonated type), Lanasyn Blue S-BL(monosulphonated type) and Kayakalan Black BGL(disulphonated type). The dyeing rate of UMF nylon 6 is faster than that of regular nylon 6. From the results of absorption isotherms, the regular nylon 6 has higher saturation value of Acid Red 18 compared with UMF nylon 6, whereas UMF nylon 6 has higher saturation value of the acid Blue 113. From the absorption isotherms of both acid dyes, the regular nylon 6 has higher saturation value of Acid Red 18, whereas UMF nylon 6 has higher saturation value of the acid Blue 113. The wash fastnesses of UMF nylon 6 increases in the order of metal-complek dye containing nonsulphonated group > monosulphonated group>disulphonated group. Aftertreatment of UMF nylon 6 dyed with unsulponated and monosulphonated dyes improves wash fastness upto grade 1.5, where as that of UMF nylon 6 dyes with disulphonated dye does not improve wash fastness.

• 한국전기전자재료학회논문지
• /
• 제20권11호
• /
• pp.995-999
• /
• 2007

We investigated the characteristics of a flux-lock type superconducting fault current limiter(SFCL) considering magnetization characteristic of iron core. The flux-lock type SFCL, like other types of SFCLs using the iron core, undergoes the saturation of the iron core during the initial fault time. Therefore, if the design to prevent the saturation of the iron core is considered, the effective fault current limiting operation can be achieved. Through the analysis for its equivalent circuit including the magnetization characteristic of the iron core, the limiting impedance of the flux-lock type SFCL was drawn. The magnetization currents and the limited currents of SFCL, which were dependent on the winding direction and the turns' ratio between two coils, were investigated from the short circuit experiment. It was confirmed that their experimental results agreed with the analysis ones.

• 상하수도학회지
• /
• 제12권1호
• /
• pp.62-69
• /
• 1998

To remove nitrogen from wastewater, ammonia nitrogen has to be oxidized to nitrate nitrogen before denitrification reaction which converts nitrate nitrogen to nitrogen gas. In order to understand nitrification, several mathematical models had been proposed and Monod type model has been accepted internationally. Since Monod type model consists of maximum substrate utilization rate, substrate concentration and half-saturation coefficient, these values have to be addressed before using Monod type model. Several experimental procedures to determine half-saturation coefficient have been developed, however, Infinite dilution method was known to be time saving procedure. In this study, the mathematical equations and experimantal procedures for Infinite dilution method are presented and this method is used to determine half-Saturation coefficient for nitrifying bacteria. As results, Infinite dilution method is proved that this coefficient can be determined within 8 hours and the values of half-saturation coefficient has a range of 0.728 and $0.455gNH_4{^+}-N/m^3$ and the average has $0.580gNH_4{^+}-N/m^3$ through 5 sets of experiments.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.1942-1946
• /
• 2009

This paper presents a shape design process of Claw-Poles Stepping Motor(CPSM) using Modified Magnetic Equivalent Circuit Method(MMEC). Because this motor is adopted on low power devices, the motor size is a very small type. But it have a very strong permanent magnet. So magnetic saturation effect happens on yoke teeth of CPSM. Also this magnetic saturation effect causes more leakage flux component between yoke tooth have another pole. In this motor type, it is essential to design a shape of yoke teeth for avoiding the magnetic saturation effect and the leakage flux. In this paper, MMEC including the magnetic saturation effect and the leakage flux component was used for design process. Comparing with data calculated by using the MMEC and results analyzed by 3-D FEM, it could be stated that the design process with MMEC was reasonable. Finally, the model has the optimized shape of yoke teeth was compared with a conventional model for no-load Back EMF and torque at steady-state operation.

• 한국컴퓨터정보학회논문지
• /
• 제15권3호
• /
• pp.11-18
• /
• 2010

본 연구에서는 광전용적맥파를 이용하여 요골동맥에서 맥박 및 산소포화도를 검출하였다. 반사형으로 고안된 디바이스를 이용하여 요골동맥에서의 반사광은 수신부를 통해 측정되고, 이 측정된 신호는 스위칭을 통해 각각 625nm, 940nm의 파장대역의 신호로 분리된다. 분리된 신호는 각각의 맥박신호처리회로를 통해 맥박데이터로 구현된다. 본 연구에서는 반사 방식으로 손목부근의 요골동맥을 측정하였기에 투과방식이 아닌 반사방식의 산소포화도 측정에 적합한 방법을 적용하여 결과를 얻었다. 얻어진 결과는 약 97%정도의 정확도로 산소포화도를 검출할 수 있었다. 또한, 정확한 신호를 얻기 위해서 요골동맥에 센서가 장착된 밴드를 이용하여 측정 하였으며, 고정이 되도록 압박을 하였다. 결과로서 손목밴드의 장착을 통해 움직임에 의한 측정위치에러를 방지할 수 있었으며, 이에 따른 정확도를 높일 수 있었다.

• 한국광학회지
• /
• 제2권2호
• /
• pp.67-73
• /
• 1991

단일 종모드로 동작하며, 10mW의 출력을 가지는 AlGaAs 반도체 레이저를 이용하여 Fabry-Perot 공진기형 레이저 증폭기 시스템을 구성하고 비포화 신호이득(unsaturated signal gain), 신호이득 대역폭(signal gain bandwidth), 포화출력(saturation power)을 측정하였다. 증폭기 레이저의 펌핑전류에 따른 비포화 신호 이득은 발진 문턱 전류 근처에서 $0.7\mu\textrmW$의 레이저 출력을 증폭기 레이저에 입사시켰을 때 최대 25dB을 얻었으며 이때 신호이득의 대역폭이 3 GHz 정도임을 확인하였다. 또한 입력 세기(input power)에 따른 비포화 신호이득의 변화를 측정하고 이때의 포화출력을 측정하였다.

• 한국소음진동공학회논문집
• /
• 제16권2호
• /
• pp.207-213
• /
• 2006

In our previous research, we proposed a robust saturation controller which involves both control input saturation and structured real parameter uncertainties. This controller can analytically prescribed the upper and lower bounds of parameter uncertainties, and guarantee the closed-loop robust stability of the system in the presence of actuator's saturation. And the availability and the effectiveness of the proposed robust saturation controller were verified through numerical simulations. In this paper, we verify the robust stability of this controller through experimental tests. Expecially, we show unstable cases of other controllers in comparison with this controller. Experimental tests are carried out in the laboratory using a two-story test structure with a hydraulic-type active mass damper.