• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.35-41
• /
• 2012

Manifold researches for carbon capture and storage (CCS) have been developed and large scale-carbon capture system can be performed recently. Hence, the technologies for $CO_2$ sequestration or storage become necessary to handle the captured $CO_2$. Among them, enhanced oil recovery using $CO_2$ can be a solution since it guarantees both oil recovery and $CO_2$ sequestration. In this study, the miscible flow of oil and $CO_2$ in porous media is modeled to analyze the effect of enhanced oil recovery and $CO_2$ sequestration. Based on Darcy-Muskat law, the equation is modified to consider miscibility of oil and $CO_2$ and the change of viscosity. Finite volume method is used for numerical modeling. As results, the pressure and oil saturation changes with time can be predicted when oil, water, and $CO_2$ are injected, respectively, and $CO_2$ injection is more efficient than water injection for oil recovery.

• Journal of Conservation Science
• /
• v.7 no.2
• /
• pp.60-67
• /
• 1998

The effects of moisture content (MC) and diffusion period on the diffusion of boron from borate rod through Pinus densiflora and P. koraiensis were investigated as a preliminary research of integrated remedial treatment for heritage wooden structures using borate rod. After equilibrating MCs of samples (15, 25, and 40%), borate rod (1,000 mg) was inserted into the sample, and stored for diffusion of boron at room temperatures ($23^{\circ}C$) for 2, 4, 8, and 12 weeks. Wafers were serially cut at constant intervals from rod treatment point and the boron penetration through longitudinal and transverse direction was measured by staining with boron indicator. For boron diffusion, MC above fiber saturation point was needed, and the diffusion rates increased with time. The fastest rates of diffusion were observed in longitudinal direction, followed by the radial and then the tangential direction. The rates of diffusion in all directions were the fastest in P. koraiensis. In P. densiflora, the diffusion rates through heartwood was faster than that in sapwood in longitudinal direction and vice versa in transverse direction. Based on the best result of this study, optimal space between rod insertion points could be recommended as follows; approximately 120 mm for P. koraiensis and heartwood of P. densiflora, 60 mm for sapwood of P. densiflora in longitudinal direction, and approximately 30 mm for all species tested in transverse direction. However, the effect of rod size and long-term exposure for diffusion on boron movement should be fully investigated for the accurate evaluation of optimal space between rod holes.

• Cartoon and Animation Studies
• /
• s.39
• /
• pp.393-412
• /
• 2015

See and feel the emotion recognition is the image of a person variously changed according to the environment, personal disposition. Thus, the image recognition has been focused on the emotional sensibilities computer you want to control the number studies. However, existing emotional computing model is numbered and the objective is clearly insufficient measurement conditions. Thus, through quantifiable image Emotion Recognition and emotion computing, is a study of the situation requires an objective assessment scheme. In this paper, the sensitivity was represented by numbered sizes quantified according to the image recognition calculation emotion. So apply the principal attributes of the color image emotion recognition as a configuration parameter. In addition, in calculating the color sensitivity by applying a digital computing focused research. Image color emotion computing research approach is the color of emotion attribute, brightness, and saturation reflects the weighted according to importance to the emotional scores. And free-degree by applying the sensitivity point to the image sensitivity formula (X), the tone (Y-axis) is calculated as a number system. There pleasure degree (X-axis), the tension and position the position of the image point that the sensitivity of the emotional coordinate crossing (Y-axis). Image color coordinates by applying the core emotional effect of Russell (Core Affect) is based on the 16 main representatives emotion. Thus, the image recognition sensitivity and compares the number size. Depending on the magnitude of the sensitivity scores demonstrate this sensitivity must change. Compare the way the images are divided up the top five of emotion recognition emotion emotions associated with 16 representatives, and representatives analyzed the concentrated emotion sizes. Future studies are needed emotional computing method of calculation to be more similar sensibility and human emotion recognition.

• Korean Journal of Soil Science and Fertilizer
• /
• v.47 no.4
• /
• pp.269-274
• /
• 2014

Series of field experiments were conducted to evaluate the long term effect of gypsum and crop residue on crop yield and soil health in rice-wheat crop rotation system in salt affected soil. A saline-sodic field having $EC_e$ (electrical conductivity of the saturation extract) 4.77 ($dSm^{-1}$); pH ($H_2O$) 8.96; SAR 43.78 ($mmol\;L^{-1}$) and gypsum requirement (G.R.) 2.86 (Mg $acre^{-1}$) was selected on Soil Salinity Research Institute Farm. Five treatments consisting of ($T_1$) control, ($T_2$) gypsum at 100% G.R., ($T_3$) gypsum at 25% G.R. + wheat straw at $3Mg\;ha^{-1}$, ($T_4$) gypsum at 25% G.R. + rice straw at $3Mg\;ha^{-1}$, ($T_5$) gypsum at 25% G.R.+ rice and wheat straw at $3Mg\;ha^{-1}$ were replicated four times under completely randomized block design. The data indicated that grain and straw yield of rice and wheat was significantly (P<0.05) increased by all the amendments used either single or in combination. $T_2$ (gypsum at 100% G.R.) significantly (P<0.05) increased grain and straw yield of rice and wheat crops followed by $T_3$ (gypsum at 25% G.R. + wheat straw at $3Mg\;ha^{-1}$) when compared with control. Soil properties were also improved by used amendments, pronounced decreased in $EC_e$, $pH_s$ and SAR were recorded in $T_2$ followed by $T_3$. The efficiency of the treatments could be arranged in following order gypsum at 100% G.R.> gypsum at 25% G.R. + wheat straw at $3Mg\;ha^{-1}$ > gypsum at 25% G.R. + rice and wheat straw at $3Mg\;ha^{-1}$ > gypsum at 25% G.R. + rice straw at $3Mg\;ha^{-1}$ > control.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.135-135
• /
• 2010

In Mn-Ge equilibrium phase diagram, many Mn-Ge intermetallic phases can be formed with difference structures and magnetic properties. The MnGe has the cubic structure and antiferromagnetic(AFM) with Neel temperature of 197 K. The calculation predicted that the $MnGe_2$ with $Al_2Cu$-type is hard to separate between the paramagnetic(PM) states and the AFM states because this compound displays PM and AFM configuration swith similar energy. Mn-doped Ge showed the FM with Currie temperature of 285 K for bulk samples and 116 K for thin films. In addition, the $Mn_5Ge_3$ compound has hexagonal structure and FM with Curie temperature around 296K. The $Mn_{11}Ge_8$ compound has the orthorhombic structure and Tc is low at 274 K and spin flopping transition is near to 140 K. While the bulk $Mn_3Ge_2$ exhibited tetragonal structure ($a=5.745{\AA}$;$c=13.89{\AA}$) with the FM near to 300K and AFM below 150K. However, amorphous $Mn_3Ge_2$ ($a-Mn_3Ge_2$) was reported to show spin glass behavior with spin-glass transition temperature (Tg) of 53 K. In addition, the transition of crystalline $Mn_3Ge_2$ shifts under high pressure. At the atmospheric pressure, $Mn_3Ge_2$ undergoes the magnetic phase transition from AFM to FM at 158 K. The pressure dependence of the phase transition in $Mn_3Ge_2$ has been determined up to 1 GPa. The transition was found to occur at 1 GPa and 155 K with dT/dP=-0.3K/0.1 GPa. Here report that Ferromagnetic $Mn_3Ge_2$ thin films were successfully grown on GaAs(001) and GaSb(001) substrates using molecular beam epitaxy. Our result revealed that the substrate facilitates to modify magnetic and electrical properties due to tensile/compressive strain effect. The spin-flopping transition around 145 K remained for samples grown on GaSb(001) while it completely disappeared for samples grown on GaAs(001). The antiferromagnetism below 145K changed to ferromagnetism and remained upto 327K. The saturation magnetization was found to be 1.32 and $0.23\;{\mu}B/Mn$ at 5 K for samples grown on GaAs(001) and GaSb(001), respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.3
• /
• pp.574-579
• /
• 2008

The evaporation heat transfer coefficient of $CO_2$ (R-744) in a horizontal tube was investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator (test section). The test section consists of a smooth, horizontal stainless steel tube of inner diameter of 4.57mm. The experiments were conducted at mass flux of 400 to $900kg/m^2s$, saturation temperature of 5 to $20^{\circ}C$, and heat flux of 10 to $40kW/m^2$. The test results showed the heat transfer of $CO_2$ has a greater effect on nucleate boiling more than convective boiling. Mass flux of $CO_2$ does not affect nucleate boiling too much. In comparison with test results and existing correlations, All of the existing correlations for the heat transfer coefficient underestimated the experimental data. However Jung et al.'s correlation showed a good agreement with the experimental data. Therefore, it is necessary to develope accurate predictions determining the evaporation heat transfer coefficient of $CO_2$ in horizontal tubes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.169-169
• /
• 2010

As display industry requires various applications for future display technology, which can guarantees high level of flexibility and transparency on display panel, oxide semiconductor materials are regarded as one of the best candidates. $InGaZnO_4$(IGZO) has gathered much attention as a post-transition metal oxide used in active layer in thin-film transistor. Due to its high mobility fabricated at low temperature fabrication process, which is proper for application to display backplanes and use in flexible and/or transparent electronics. Electrical performance of amorphous oxide semiconductors depends on the resistance of the interface between source/drain metal contact and active layer. It is also affected by sheet resistance on IGZO thin film. Controlling contact/sheet resistance has been a hot issue for improving electrical properties of AOS(Amorphous oxide semiconductor). To overcome this problem, post-annealing has been introduced. In other words, through post-annealing process, saturation mobility, on/off ratio, drain current of the device all increase. In this research, we studied on the relation between device's resistance and post-annealing temperature. So far as many post-annealing effects have been reported, this research especially analyzed the change of electrical properties by increasing post-annealing temperature. We fabricated 6 main samples. After a-IGZO deposition, Samples were post-annealed in 5 different temperatures; as-deposited, $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$ and $500^{\circ}C$. Metal deposition was done on these samples by using Mo through E-beam evaporation. For analysis, three analysis methods were used; IV-characteristics by probe station, surface roughness by AFM, metal oxidation by FE-SEM. Experimental results say that contact resistance increased because of the metal oxidation on metal contact and rough surface of a-IGZO layer. we can suggest some of the possible solutions to overcome resistance effect for the improvement of TFT electrical performances.

• Journal of the Korean Magnetics Society
• /
• v.17 no.3
• /
• pp.124-127
• /
• 2007

Magnetic tunnel junctions (MTJs), which consisted of amorphous CoFeSiB layers, were investigated. The CoFeSiB layers were used to substitute for the traditionally used CoFe and/or NiFe layers with an emphasis given on understanding the effect of the amorphous free layer on the switching characteristics of the MTJs. CoFeSiB has a lower saturation magnetization ($M_s\;:\;560\;emu/cm^3$) and a higher anisotropy constant ($K_u\;:\;2800\;erg/cm^3$) than CoFe and NiFe, respectively. An exchange coupling energy ($J_{ex}$) of $-0.003\;erg/cm^2$ was observed by inserting a 1.0 nm Ru layer in between CoFeSiB layers. In the Si/$SiO_2$/Ta 45/Ru 9.5/IrMn 10/CoFe 7/$AlO_x$/CoFeSiB 7 or CoFeSiB (t)/Ru 1.0/CoFeSiB (7-t)/Ru 60 (in nm) MTJs structure, it was found that the size dependence of the switching field originated in the lower $J_{ex}$ using the experimental and simulation results. The CoFeSiB synthetic antiferromagnet structures were proved to be beneficial for the switching characteristics such as reducing the coercivity ($H_c$) and increasing the sensitivity in micrometer size, even in submicrometer sized elements.

• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.1
• /
• pp.39-44
• /
• 1989

This experiment was conducted to mature newly reclaimed upland and to increase soybean yield at this upland, Kim Jae, Jeon Buk, Koera from 1987 to 1988. Lime, lime-magnesium and calcium sulfate were applied with two, levels, amount of lime requirement, and 1.5 times of lime requirement. The results were summarized as follows: 1. The yields of soybean among treaments were in order of lime-magnesium 1.5 times, lime 1.5 times, lime-magnesium, calcium sulfate, lime and control with significancy at 1% level. 2. Correlations between yield components and inorganic element contents (T-N, $P_2O_5$, CaO and MgO) in plant at flowering stage were positive, but manganese in plant was negative at 5%, respectively. 3. Correlations, between yields and MgO and CaO contents in plant at flowering stage were positive, but Mn in plant was negative at 5% respectively. 4. Inorganic element contents of the soils at flowering stage were higher than those of before experiment. Correlation between yield and base saturation degree in soil at flowering stage was positive at 5%.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.6
• /
• pp.483-494
• /
• 2022

Owing to the saturation of ground spaces in downtown areas, underground spaces are being developed increasingly. Underground spaces are utilized for transportation, water supply and sewerage, communication zones, electric power zones, and various cultural complexes. In Korea, for excavating underground spaces, blasting methods using gunpowder such as the New Austrian Tunneling Method (NATM) are mainly used. However, the blasting method causes vibration and noise during tunnel excavation, generating many complaints from residents in the vicinity of the excavation site. To address this problem, various methods have been developed, and recently, vibration and noise have been reduced using deep excavation. This study predicts blast vibration changes according to the depth, under the same blasting and tunnel conditions, using numerical analysis based on the blast vibration measurement data of the GTX-A route, the tunnel cross-section drawings, and ground investigation reports. Furthermore, the necessary separation distance from densely populated areas such as residential areas is suggested by analyzing the trend of decreasing blast vibration according to the distance from ground surface directly above the blasting location.