• 한국위성정보통신학회논문지
• /
• 제3권2호
• /
• pp.18-25
• /
• 2008

A major drawback of Orthogonal Frequency Division Multiplexing (OFDM) system is high peak-to-average power ratio (PAPR) of the transmitted signal which introduces inevitable non-linear distortion in the transmission due to the amplifier non-linear property. This causes both in-band distortion and out of band spectrum re-growth. A polynomial based pre-distortion is estimated using the non-linear and inverse non-linear polynomial achieved through the Least Square Error (LSE) method. A new technique of PAPR reduction called 'Phase Realignment' (PR) is proposed which has a optimal effect in improving the BER performance as well as considerable reduction in the PAPR. In this paper we used the PR method along with the 'Peak Clipping' (PC) method is used before the pre-distortion to remove the high peak present in the non constant amplitude of the OFDM signal responsible to drive the amplifier in near saturation region for better performance of the system.

• 터널과지하공간
• /
• 제30권4호
• /
• pp.417-431
• /
• 2020

이 연구에서는 라이다(LiDAR) 반사강도를 이용하여 암반 풍화도 및 변질도를 산정하는 작업의 기초연구를 진행하였다. 실내 시험을 통하여 라이다 반사강도에 직접적으로 영향을 미치는 인자와 그 영향 정도를 정량적으로 고찰하고자 하였다. 영향 인자로는 주사거리, 입사각, 표면거칠기, 표면색상, 암석물성, 광물조성, 포화도를 선정하였다. 실험에서는 FARO 라이다 장비와 12가지 종류의 시험편을 사용하였다. 실험 결과 반사강도는 표면색상, 입사각, 주사거리, 암석물성, 포화도 혹은 표면습윤상태, 표면거칠기 순으로 영향을 크게 미치는 것으로 나타났다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.100.2-100.2
• /
• 2012

Surface texturing of crystalline silicon is carried out in alkaline solutions for anisotropic etching that leads to random pyramids of about $10{\mu}m$ in size. Recently textured pyramids size gradually reduced using new solution. In this paper, we investigated that texture pyramids size had an impact on emitter property and front electrode (Ag) contact. To make small (${\sim}3{\mu}m$) and large (${\sim}10{\mu}m$) pyramids size, texturing times control and one side texturing using a silicon nitride film were carried out. Then formation and quality of POCl3-diffused n+ emitter in furnace compare with small and large pyramids by using SEM images, simulation (SILVACO, Athena module) and emitter saturation current density (J0e). After metallization, Ag contact resistance was measured by transfer length method (TLM) pattern. And surface distributions of Ag crystallites were observed by SEM images. Also, performance of cell which is fabricated by screen-printed solar cells is compared by light I-V.

• 한국지반환경공학회 논문집
• /
• 제6권3호
• /
• pp.55-61
• /
• 2005

동다짐공법은 느슨한 지반의 개량에 주로 사용되는 공법으로 점착성 토사나 폐기물과 성토지반에도 성공적으로 적용되고 있다. 동다짐공법의 설계에 있어 지반개량심도의 결정은 중요한 요소이다. 그러나 개량심도는 다짐에너지 뿐만 아니라 다짐간격, 대상토질 특성, 포화정도 및 현장여건 등에 영향을 받고 있다. 본 연구에서는 개량심도 예측을 위하여 현장실험결과를 이용하였으며 다짐에너지, 토질특성 및 포화정도에 따른 개량심도를 평가하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.310-312
• /
• 2004

Binary Exponential Back-off (BEB) scheme is widely adopted in both wire and wireless networks for collision resolution. The BEB suffers from several performance drawbacks including long packet delay and low utilization since it doubles the back-off size after each collision. In addition, operation of the BEB algorithm may lead to the last-come-first-serve result among competing users and the BEB is further unstable for every arrival rate greater than 0 due to its random access property[1,2]. In this paper, we propose a deterministic back-off algorithm to reduce contention interval as much as possible for accessing the channel without collision in the back-off process. Simulation results show that our scheme offers a higher throughput as well as a lower packet transfer delay than the BEB by taking advantage of its lower collision ratio in saturation state.

• 한국전기전자재료학회논문지
• /
• 제26권8호
• /
• pp.620-623
• /
• 2013

The carbon nanotube / poly-vinylidene fluoride (CNT/PVDF) composite films for the nano-generator devices were fabricated by spray coating method using the CNT/PVDF solution, which was prepared by adding PVDF pellets into the CNT dispersed N-Methyl-2-pyrroli-done (NMP) solution. The flexible CNT/PVDF composite films were investigated by the scanning electron microscopy, which revealed that the CNTs were uniformly dispersed in the PVDF matrix and thickness of the films was approximately $20{\mu}m$. Fourier transform infra-red spectra were used to investigate crystal structure of the as-spray-coated CNT/PVDF films, and we found that they revealed extremely large portion of the ${\beta}$ phase PVDF. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the resistance didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Finally, the resulting nano-generator devices revealed reasonable current output after given mechanical stress.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.341-344
• /
• 1999

The effects of post annealing treatments of ferroelectrlclty in PZT(P $b_{1.05}$(Z $r_{0.52}$, $Ti_{0.48}$) $O_3$ thin film deposited on Pt/ $SiO_2$/Si substrate by RF-Magnetron sputtering methode was Investigated. Analyses by RTA(Rapid Thermal Annealing) treatments reveled that the crystallization process strongly depend on the healing temperature. The Perovskite structure with strong PZT (101) plan was obtained by RTA treatments at 75$0^{\circ}C$ With increasing RTA temperature of PZI thin films, the coercive field and remanent Polarization decreased, while saturation polarization( $P_{r}$) was decreased. P-E curves of Pt/PZT/Pt capacitor structures demonstrate typical hysteresiss loops. The measure values of $P_{r}$,. $E_{c}$ and dielectric constants by post annealed at 75$0^{\circ}C$ were 38 $\mu$C/$\textrm{cm}^2$ 35KV/cm and 974, respectively. Switching polarization versus fatigue characteristic showed 12% degradation up to 10$^{7}$ cycles.s.s.s.s.s.s.

• 한국세라믹학회지
• /
• 제32권5호
• /
• pp.543-548
• /
• 1995

Li-ferrite powders were prepared from mixture of Fe and Li salts using a hydrothermal method. Their crystal structure, microstructure and magnetic property were investigated with X-ray diffraction analysis, chemical analysis, SEM, and VSM. In the case of using FeCl3 as a precursor, Li-ferrite powders were synthesized. However, Fe3O4 was formed when the precursor was a divalented Fe2SO4 or FeCl2. The precipitation rate of Li-ferrite was increased as the reaction temperature increased. The optimum conditions of synthesis were the mole ratio of Fe+++/Li+=2, pH 13, the reaction temperature of 25$0^{\circ}C$ and the reaction time of 120min. With this condition, the spherical particles with good dispersion were obtained with average particle size of 0.4${\mu}{\textrm}{m}$ and saturation magnetization of 65 emu/g.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 방전 플라즈마 유기절연재료 초전도 자성체연구회
• /
• pp.165-168
• /
• 2004

Bias magnet에 의한 평면자심재료의 전자기적 특성 변화를 분석하기 위해 E형 코어 사이에서 영구자석의 유무 및 위치 등의 gap 형성 조건에 따른 측성변화를 관찰하였다. 영구자석과 air Gap이 평면코어에 삽입 될 경우 높은 포화 전류값을 가지는데 이는 자기저항이 자성체에 비해서 상당히 높은 에어 갭의 존재로 인해 외부 인가 전류가 증가되어도 자성체에서 생성되는 자속이 대부분 에어갭 내에서 소비되기 때문이다. 그리고 Bias magnet 역할을 하는 영구자석을 자심재료에 가하게 되면 Bias에 의한 역자장과 자성체에서 발생하는 자장이 서로 상쇄되어 포화 전류는 증가하게 된다. 또한, Bias magnet로 영구자석을 삽입하연 공진주파수는 고주파 대역으로 이동하므로 대전류 고주파 특성이 요구되는 응용장치에 적용가능하다.

• 한국염색가공학회지
• /
• 제14권5호
• /
• pp.268-276
• /
• 2002

Poly(trimethylene terephthalate)(PTT) and Poly(ethylene terephthalate)(PET) fibers were annealed at various temperatures ranging from $100^\circ{C}$ to $230^\circ{C}$ for 10 min under tension and tension free. Dyeing rates and absorption isotherms of both fibers were obtained with C.I. Disperse Red 60 at 100, 120 and $130^\circ{C}$ in water system. Also X-ray diffraction pattern, moisture regain and water absorption were investigated. The dyeing rate of PTT fiber is faster than PET fiber, and dyeing of PTT fiber begin at lower temperature compared to PET fiber. The absorption isotherms from both fibers with disperse dye we nearly linear up to the saturation dye uptake, which increase with dyeing temperature. Equilibrium dye uptake of PTT fiber annealed under tension above $180^\circ{C}$ was remarkably decreased because of a changes in the fine structure of fiber. The intensities of X-ray diffraction peaks of both annealed fibers were increased with increasing in annealed temperature. The reflections observed at $2\theta$=$15.8^\circ$, $24^\circ$ and $25.2^\circ$ were assigned reflection of crystal at the planes of (010), $(1\bar02,\;\bar112),\;and\;(\bar13,\; \bar113)$ respectively, and the peak became sharp with heat setting temperature.