• Current Optics and Photonics
• /
• v.7 no.1
• /
• pp.28-32
• /
• 2023

Frequency characteristics of gain-saturated erbium-doped fiber amplifier (EDFA) are experimentally evaluated to mitigate the optical signal fluctuation induced by atmospheric turbulence in terrestrial freespace optical communication systems. Here, an acousto-optic modulator (AOM) is used to emulate optical signal fluctuations induced by atmospheric turbulence. The waveform which is generated in proportion to the refractive-index structural parameters is used to drive the AOM at various periodic frequencies. Thus, the dependence of the signal fluctuation suppression on the frequency is evaluated. The experiment is conducted using a periodic frequency sweep of the AOM driving voltage waveform and signal input power variation of the amplifier. It is observed that a low periodic frequency and high input signal power effectively suppress the optical signal fluctuation. This study evaluates the experimental results from the high-pass filter and gain-saturation characteristics of the EDFA.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.197-200
• /
• 2000

All-optical NOR logic device was realized by use of two pump signals with a single wavelength and a semiconductor optical amplifier(SOA). Specially, Mach-Zehnder(MZ) modulator was used for an external modulation of the pump signals. To obtain the sufficient gain saturation of the SOA, pump signals are amplified by an Er-doped fiber amplifier(EDFA) at the input of the SOA. Pump and probe signals are obtained from a DFB laser diode(${\lambda}_p$=1554 nm) and a tunable laser diode(${\lambda}_s$=1535 nm), respectively. The operation characteristics of the NOR logic device are successfully measured and demonstrated at the modulation frequency of 4.83 MHz.

• Journal of Satellite, Information and Communications
• /
• v.3 no.1
• /
• pp.15-21
• /
• 2008

The high peak to average power ratio (PAPR) of OFDM (Orthogonal Frequency Division Multiplexing) system introduces inevitable non-linear distortion in the transmission due to the amplifier non-linear property. This causes both in-band distortion and out of band spectrum re-growth. In this paper we tried to compensate the problem by using polynomial based pre-distortion. Estimation of both the non-linear and inverse non-linear polynomial is achieved using the Least Square Error (LSE) method. Using these parameters closed form pre-distorter can be easily created. We also used the 'partial peak cancellation and clipping' method to remove the high peak present in the non constant amplitude of the OFDM signal responsible to drive the amplifier in near saturation region for better performance of the system

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.11
• /
• pp.2697-2702
• /
• 2014

In this paper, we demonstrated a Ku-band 2W MMIC power amplifier for satellite communication applications. The device technology used relies on $0.25{\mu}m$ GaAs pseudomorphic high electron mobility transistor (PHEMT) of Wireless Information Networking (WIN) Semiconductor foundry. The 2W MMIC power amplifier has gain of over 29 dB and saturation output power of over 33.4 dBm in the frequency range of 13.75 ~ 14.5 GHz. Power added efficiency (PAE) is a 29 %. To our knowledge, this is the highest power added efficiency reported for any commercial GaAs-based 2W MMIC power amplifier in the Ku-band.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.41.3-41
• /
• 2001

In this paper, we present a decentralized adaptive neural net(NN) controller for the transient stability and voltage regulation of a multimachine power system. First, an adaptively input-output linearizing controller using NN is designed to eliminate the nonlinearities and interactions between generators. Then, a robust control term which bounds terminal voltage to a neighborhood of the operating point within the desired value is introduced using only local information. In addition, we consider input saturation which exists in the SCR amplifier and prove that the stability of the overall closed-loop system is maintained regardless of the input saturation. The design procedure is tested on a two machine infinite bus power system.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.222-223
• /
• 2003

The optical gain characteristics of 1550nm traveling-wave semiconductor optical amplifiers are analyzed experimentally and theoretically. The result shows that there is an optimum active layer thickness for high saturation output power.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.834-841
• /
• 2018

A power amplifier for subgigahertz short-range wireless communication using $0.18-{\mu}m$ CMOS technology is presented. It is designed as a differential structure to form easily a virtual ground node, to increase output power, and to design a cascode structure to prevent breakdown. The transistor gate width was determined to maximize the output power and power-added efficiency(PAE), and the balun was optimized through electromagnetic simulation to minimize the loss caused by the matching network. This power amplifier had a gain of more than 49.5 dB, a saturation power of 26.7 dBm, a peak PAE of 20.7 % in the frequency range of 860 to 960 MHz, and a chip size of $2.14mm^2$.

• Korean Journal of Optics and Photonics
• /
• v.33 no.3
• /
• pp.99-105
• /
• 2022

We have evaluated the performance of an all-optical automatic gain-controlled (AGC) erbium-doped fiber amplifier (EDFA) to suppress the optical signal fluctuation induced by atmospheric turbulence in terrestrial free-space optical communication systems. In our measurements, the input power into the EDFA was set to be -30 dBm and -10 dBm to operate the amplifier in the small-signal and saturation regions, respectively. The fluctuations in the optical signal were emulated with an acousto-optic modulator driven with a sinusoidal voltage. From the measured results, we have found that an all-optical AGC EDFA could suppress the optical signal fluctuation effectively, as long as the EDFA operated in the small-signal region with a high feedback amplified spontaneous emission (ASE) power.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.11
• /
• pp.893-900
• /
• 2021

In this study, air density in a narrow test section is measured using a laser absorption spectroscopy system that detects oxygen absorption lines. An absorption line pair at 13156.28 and 13156.62 cm^-1 are detected. A gas chamber with a height of 40 mm is used as a narrow test section. A triangular spiral-shaped laser path is applied in the gas chamber to amplify absorption strength by extending laser beam path length. A well-known logarithm amplifier and a secondary amplifier are used to electrically amplify absorption signal. An AC-coupling is applied after the logarithm amplifier for signal saturation prevention and noise suppression. Procedure of calculating spectral absorbance from output signal is introduced considering the logarithm amplifier circuit configuration. Air density is determined by fitting the theoretically calculated spectral absorbance to the measured spectral absorbance. Test conditions with room temperature and a pressure range of 10~100 kPa are made in a gas chamber using a Bourdon pressure gauge. It is confirmed that air density in a narrow test section can be measured within a 16 % error through absorption signal amplification using a triangular spiral-shaped beam path and a logarithm amplifier.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.1-6
• /
• 2001

In this article, the fundamental concept, characteristics and application potentials of coreless printed-circuit-board (PCB) transformers are described. Coreless PCB transformers do not have the limitations associated with magnetic cores, such as the frequency limitation, magnetic saturation and core losses. In addition, they eliminate the manual winding process and its associated problems, including labor cost, reliability problems and difficulties in ensuring transformer quality in the manufacturing process. The parameters of the printed windings can be precisely controlled in modern PCB technology. Because of the drastic reduction in the vertical dimension, coreless PCB transformers can achieve high power density and are suitable for applications in which stringent height requirements for the circuits have to be met. A transformer's power density of $24W/cm^2$ has been reported in a power conversion application. When used in an isolation amplifier application, coreless PCB transformers tested so far enable the amplifier to achieve a remarkable linear frequency range of 1MHz, which is almost eight times higher than the frequency range of 120kHz in existing Integrated-Circuit products. PCB materials offer extremely high isolation voltage, typically from 15kV to 40kV, which is higher than many other isolation means such as optocouplers. It is envisaged that coreless PCB transformers can replace traditional core-based transformers in some industrial applications. Their application potentials deserve more attention and exploration.