• Journal of Welding and Joining
• /
• 제1권2호
• /
• pp.69-75
• /
• 1983

Both in-process quality control and reliability of the weld is one of the major concerns is applying friction welding. No reliable nondestructive monitoring method is available at present to determine the weld quality particularly in process of production. So that, this paper presents an experimental examination and quantitative analysis for the effects of initial acoustic emission(AE) counts on the weld strength relating to the rotating speed as a new approach which attempts finally to develop an on-line quality monitoring system design for friction welds using AE techniques. As one of the important results, it was well confirmed that the initial AE counts occurring during plastic deformation period of welding were quantitatively correlated with reliability at 95% confidence level to the joint strength of welds, tube-to-tube (SM 20 C to STS 304) and then an AE technique using the initial AE counts can be reliably applied to in-process strength monitoring of the weld.

• Journal of Welding and Joining
• /
• 제20권1호
• /
• pp.26-33
• /
• 2002

This study was undertaken to obtain the fundamental knowledges on the weld deflects and it's realtime monitoring method. The paper describes the results of high speed photography, acoustic emission (AE) detection and plasma light emission (LE) measurements during $CO_2$ laser welding of STS 304 stainless steel and A5083 aluminum alloy in different welding condition. The characteristic frequencies of plasma and keyhole fluctuations at different welding speed and shield gases were measured and compared with the results of Fourier analyses of temporal AE and LE spectra, and they had considerably good agreement with keyhole and plasma fluctuation. Namely, the low frequency peaks of AE and LE shifted to higher frequency range with the welding speed increase, and leer the argon shield gas it was higher than that in helium and nitrogen gases. The low frequencies dominating in fluctuation spectra of LE probably reflect keyhole opening instability. It is possible to monitor the weld bead deflects by analyzing the acoustic and/or plasma light emission signals.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 추계학술대회 초록집
• /
• pp.200-200
• /
• 2009

아크이온플래이팅 기술과 DC 마그네트론 스퍼터링 기술이 결합된 하이브리드 코팅 시스템을 이용하여 STS 304와 Si 기판에 4성분계 CrAlCxN1-x 코팅을 증착하였다. 합성된 CrAlCxN1-x 코팅은 주로 유도결합형로 f구성되었다. CrAlCxN1-x 코팅의 carbon 함량이 0.17 at.%일 때 약 34 GPa을 나타내었으며 마찰계수는 carbon 함량이 0에서 1 at.%로 증가함에 따라 0.82에서 0.38까지 크게 감소하였다. 이는 코팅 표면과 steel 볼 사이에 amorphous carbon layer가 형성되어 고체윤활제로 작용한 것으로 사료된다.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.108-113
• /
• 2010

Decreasing products lifecycles and increasing consumers desires for quality and design make the automotive industries try to reduce time for developing new designs. In order to reduce developing time, I have designed head lamps, which are really important to have an effect on brand identities and images, using layers concept that is one of the international automotive design trends by alias and photoshop, and produced prototype by RP. To assemble the produced prototype to the body and manufacture the frame to exterior modelling efficiently, I have studied on joining dissimilar materials of aluminum alloy that can make the prototype lighter and stainless steel, which is good for corrosion resistance by using laser beam. These materials were welded for finding the optimum joining condition and evaluating the soundness of joining zone. The joining was performed under the condition of laser power 500, 550, 575, 600W and 11~14Hz. In this study, the suitable joining condition between aluminum alloy (Al 2024) and stainless steel (STS 304) can be obtained at the laser power 575W and frequency 12Hz.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.102-108
• /
• 1998

본 논문에서는 Nd-YAG 레이저 용접 프로세스를 이용하여 두께가 다른 STS304스테인레스 박강판을 대상으로한 점용접에 관한 연구로서, 레이저 용접은 미소부위에 효율적인 접합가공이 가능한 공정으로 비접촉식 가열원을 이용하기 때문에 접합공정 중 기계적 변형이 없고, 레이저 빔을 국부가열원으로 하여 매우 좁은 부분에 제한적으로 열을 가할 수 있어서 강한 금속적 결합이 요구되는 소형부품의 접합에 이용될 수 있다. 뿐만 아니라 공정 변수들을 변화시켜 실제 접합부에 들어 가는 입열량을 쉽게 제어할 수 있다는 등 많은 장점을 가지고 있다. 본 연구에서는 1mm이하의 스테인레스 박판에 대한 레이저 점용접을 FDM과 신경회로망을 이용하여 해석하고 용접부의 너겟 크기, 용접부 깊이 등의 형상을 예측하였다. 또한 레이저 점용접에 있어서의 주요 변수인 펄스 에너지, 펄스 타임, 박판의 두께, 두 판사이의 간극크기 등득 변화시켜 실험하고 수치해석을 검증하기 위하여 여러 가지 강에 대한 레이저 점용접 실험을 수행하였다. 또한 수치해석 시뮬레이션을 위하여 윈도우 프로그래밍을 개발하였다.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.34-44
• /
• 1996

Austenite stainless steel was produced by arc welding with current 650A, voltage 50V and welding speed 10cm/min. It was post-welded and then heat treated at $1,050^{\circ}C$ for 120min. And then it was immersed in water or in air. The microstructural changes, ferrite contents, mechanical properties, and stress corrosion cracking(SCC) were investigated. The SCC was studied in 42wt% boiling $MgCl_2$($140^{\circ}C$) under the constant stress using SCC elongation curve. The results showed that; 1. The as-welded spedimen seemed to increase ${\delta}$-ferrite content largely, and revealed continuous network of lathy and vermicular type. The post-welded heat treatment changed the morphologies of ferrite from continuous type to island type. 2. The as-welded, air and water quenched specimens had the ${\delta}$-ferrite content 9.7%, 3.2% and 2.1% respectively. We also showed that ${\delta}$-ferrite was Cr-rich and Ni-poor by EPMA. 3. The time of failure on the SCC was measured and it was used for corrosion elongation curve. The condition of SCC was investigated under $35kgf/mm^2$ load and the results were as follows; 4. The intergranullar cracking by stress corrosion was most distinct in weld metal while the transgranular cracking occurred in the air cooled specimen.

• 한국재료학회지
• /
• 제12권10호
• /
• pp.776-783
• /
• 2002

Austenitic stainless steel (STS304) has been carburized using glow discharge plasma and its microstructure, wear resistance and corrosion property have been investigated. A repeat boost-diffuse carburizing was used as an effective plasma carburizing method. The effective case depth of the plasma carburized specimens was increased with the carbon concentration at the surface area. The specimens prepared by 3 hours plasma carburizing under $600^{\circ}C$ did not have the standard hardness for the effective case depth, but the specimen prepared by 11 hours plasma carburizing at $500^{\circ}C$ had nearly the same hardness with the specimen plasma carburized for 3 hours at $800^{\circ}C$. The wear resistance increased with temperature but the corrosion properties of the specimens prepared over $600^{\circ}C$ decreased rapidly due to the grain boundary sensitization. However, the specimen plasma carburized for 11 hours at $500^{\circ}C$ had nearly the same wear resistance with the specimen plasma carburized for 3 hours at $800^{\circ}C$ without deterioration of corrosion property. This could be resulted from the fact that the microstructure of the specimen plasma carburized for 11 hours at $500^{\circ}C$ was composed of martensite and austenite, because a partial martensite transformation was occurred only in the specimen plasma carburized for 11 hours at 50$0^{\circ}C$.

• Journal of Welding and Joining
• /
• 제19권6호
• /
• pp.622-629
• /
• 2001

The aim of this experiment is to establish the method that obtains symmetrically two nuggets in microresistance series spot welding. The sheets of austenite stainless steel STS304 applied to various electronic parts were experimented by the inverter welding power source of polarity controllable type and by the twin head for left and right electrode force to be controlled separately. The experimental results were obtained as follows : 1) When series spot welding was carried out by DC 1 pulse as welding current with same electrode force at left and right, the asymmetry of nuggets was resulted from the larger nugget of the (-) pole because of the Peltier effect. The dynamic resistance of weld spot at left and right was appeared differently according to the growth of nuggets. 2) When AC 1 cycle by welding power source of polarity controllable type was applied, the nuggets were almost symmetrically formed. 3) In a twin head, if the electrode force of (-) pole was larger than that of (+) pole, the diameters of two nuggets became to same. It was confirmed that the dynamic resistance of (-) pole was decreased to the same level as it of (+) pole. 4) Although the forces of left and right electrode were same, and only DC 1 pulse was applied, symmetric nuggets were obtained if the conductivity of (+) pole was lower than it of (-) pole.

• 대한공업교육학회지
• /
• 제31권2호
• /
• pp.350-363
• /
• 2006

최근 마이크로 엔드밀을 이용한 가공은 소형구조물이나 소형기계의 부품과 금형산업에서 양호한 표면 거칠기와 가공시간의 단축을 위해 고정도의 기술을 요구하고 있다. 마이크로 엔드밀을 이용한 가공에 있어서 가공조건은 절삭면의 표면거칠기에 커다란 영향을 미치게 된다. 따라서 본 연구에서는 마이크로 엔드밀을 이용하여 스테인리스 강(STS 304)의 표면을 가공하였고, 실험계획법에 의해 최적의 표면거칠기를 얻기 위한 가공조건에 대해 분산분석하였다. 본 연구를 통하여 마이크로 엔드밀에 의한 가공에서 가공조건은 절삭깊이, 스핀들의 회전수, 이송속도의 순서로 표면거칠기에 영향을 미치는 것을 알았다.

• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.49-57
• /
• 2007

The optimization of the cladding parameters was studied to maximize the deposition efficiency in the laser cladding using a low power pulsed Nd:YAG laser. STS304 stainless steel plate and Co alloy powder were used as a substrate and powder for cladding, respectively. The six cladding parameters were selected through preliminary experiments and their effects on the deposition efficiency were analyzed statistically. Experiments were designed and carried out using the Taguchi experimental method using a L18 orthogonal array. It was found from the results of analysis of variance(ANOVA) that the powder feed position and powder feed angle had the most significant effects on the deposition efficiency, but the powder feed rate and laser focal position had nearly no effects. The deposition efficiency could be maximized at 0mm of the powder feed position and 50o of the powder feed angle in the experimental range. From this experimental analysis, a new laser cladding head with 20o of the powder feed angle was designed and manufactured. With a new laser cladding head, the highest deposition efficiency of 12.2% could be obtained.