• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.60-60
• /
• 2003

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2006년도 춘계학술발표대회 및 제10회 신소재 심포지엄 논문개요집
• /
• pp.19.1-19.1
• /
• 2006

• 한국정보과학회:학술대회논문집
• /
• 한국정보과학회 1998년도 가을 학술발표논문집 Vol.25 No.2 (2)
• /
• pp.674-676
• /
• 1998

소자가 sub-quarter um급으로 축소됨에 따라 STI(Shallow Trench Isolation) 기술은 고 집적도의 ULSI 구현에 있어서 중요한 격리 방법으로 많이 사용되고 있다. 현재의 STI 기술은 주로 실리콘 기판을 식각 후 절연물질로 빈 공백이 없이 채우는 (void-free gap filling) 방법 [1,2]과 절연물질을 다시 표면 근처까지 CMP(Chemical Mechnical Polishing)로 etchback하여 평탄화를 하는 방법이 주요한 기술이 되고 있다. 또한 STI 구조로된 격리구조에서 만들어진 MOSFET의 전기적인 특성은 트랜치 격리의 상부 부분의 형태와 gap-filling 물질에 따라 큰 영향을 받게된다. 따라서 본 논문에서는 STI 구조로 만들어진 격리 구조에서 MOSFET의 hump 특성에 관해 연구하였다. 그 결과 hump는 STI 모서리에서 필드 옥사이드의 recess에 의한 모서리 부분에서의 전계 집중과 boron의 segration에 기인한 농도 감소로 인해 hump가 발생하는 것으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.239-242
• /
• 2004

We investigated the nanotopography impact on the post-chemical mechanical polishing (post-CMP) oxide thickness deviation(OTD) of ceria slurry with a surfactant. Not only the surfactant but also the slurry abrasive size influenced the nanotopography impact. The magnitude of the post-CMP OTD increased with adding the surfactant in the case of smaller abrasives, but it did not increase in the case of larger abrasives, while the magnitudes of the nanotopography heights are all similar. We created a one-dimensional numercal simulation of the nanotopography impact by taking account of the non-Prestonian behavior of the slurry, and good agreement with experiment results was obtained.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.561-562
• /
• 2006

The purpose of this study was to investigate the root cause of adhesion of silica and ceria particles during Poly-Si, TEOS, and SiN CMP process, respectively. The zeta-potentials of abrasive particles and wafers were observed negative surface charges in the alkaline solutions. SAC and STI patterned wafers have intermediate values of their composition surface's zeta potentials. The theoretical interaction force and adhesion force of silica and ceria particle were calculated in solution with acidic, neutral and alkaline pH. A stronger attractive force was calculated for silica and ceria particles on wafers in acidic solutions than in alkaline solutions. The theoretical interaction forces of the SAC and STI patterned wafers have intermediate values of their constitution wafer's values. The adhesion forces is observed lower values in alkaline solutions than in acidic solutions. And the ceria particle has lower adhesion than that of the silica particle.

• 한국시뮬레이션학회논문지
• /
• 제11권1호
• /
• pp.23-30
• /
• 2002

An STI(Shallow Trench Isolation) by using a CMP(Chemical Mechanical Polishing) process has been one of the key issues in the device isolation[1] In this paper we fabricated N, P-MOSFEET tall analyse hump characteristics in various rounding oxdation thickness(ex : Skip, 500, 800, 1000$\AA$). As a result we found that hump occurred at STI channel edge region by field oxide recess. and boron segregation(early turn on due to boron segregatiorn at channel edge). Therefore we improved that hump occurrence by increased oxidation thickness, and control field oxide recess( 20nm), wet oxidation etch time(19HF,30sec), STI nitride wet cleaning time(99HF, 60sec+P 90min) and fate pre-oxidation cleaning time (U10min+19HF, 60sec) to prevent hump occurring at STI channel edge.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2007년도 추계학술발표대회 및
• /
• pp.7.2-7.2
• /
• 2007

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.185-188
• /
• 2001

Chemical mechanical polishing(CMP) process is widely used for global planarization of inter-metal dielectric (IMD) layer and inter-layer dielectric (ILD) for deep sub-micron technology. However, as the IMD and ILD layer gets thinner, defects such as micro-scratch lead to severe circuit failure, which affect yield. In this paper, for the improvement of CMP process, deionized water (DIW) pressure, purified $N_2 \; (PN_2)$ gas, slurry filter and high spray bar were installed. Our experimental results show that DIW pressure and $PN_2$ gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. Also, the filter installation in CMP polisher could reduce defects after CMP process, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. However, the slurry filter is impossible to prevent defect-causing particles perfectly. Thus, we suggest that it is necessary to install the high spray bar of de-ionized water (DIW) with high pressure, to overcome the weak-point of slurry filter. Finally, we could expect the improvements of throughput, yield and stability in the ULSI fabrication process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.118-118
• /
• 2008

The oxide CMP has been applied to interlayer dielectric(ILD) and shallow trench isolation (STI) in chip fabrication. Recently the slurry used in oxide CMP being changed from silica slurry to ceria (cerium dioxide) slurry particularly in STI CMP, because the material selectivity of ceria slurry is better than material selectivity of silica slurry. Moreover, the ceria slurry has good a planarization efficiency, compared with silica slurry. However ceria abrasives make a material removal rate too high at the region of wafer center. Then we focuses on why profile of material removal rate is convex. The material removal rate sharply increased to 3216 $\AA$/min by $4^{th}$ run without conditioning. After $4^{th}$ run, material removal rate converged. Furthermore, profile became more convex during 12 run. And average material removal rate decreased when conditioning process is added to end of CMP process. This is due to polishing mechanism of ceria. Then the ceria abrasive remains at the pad, in particular remains more at wafer center contacted region of pad. The field emission scanning electron microscopy (FE-SEM) images showed that the pad sample in the wafer center region has a more ceria abrasive than in wafer outer region. The energy dispersive X-ray spectrometer (EDX) verified the result that ceria abrasive is deposited and more at the region of wafer center. Therefore, this result may be expected as ceria abrasives on pad surface causing the convex profile of material removal rate.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제2C권5호
• /
• pp.262-267
• /
• 2002

In this paper, we first studied the factors affecting the motor current (MC) signal, which was strongly affected by the systematic hardware noises depending on polishing such as pad conditioning and arm oscillation of platen and recipe, head motor. Next, we studied the end point detection (EPD) for the chemical mechanical polishing (CMP) process of shallow trench isolation (STI) with reverse moat structure. The MC signal showed a high amplitude peak in the fore part caused by the reverse meal. pattern. We also found that the EP could not be detected properly and reproducibly due to the pad conditioning effect, especially when conventional low selectivity slurry was used. Even when there was no pad conditioning effect, the EPD method could not be applied, since the measured end points were always the same due to the characteristics of the reverse moat structure with an open nitride layer.