• Journal of Environmental Science International
• /
• v.27 no.9
• /
• pp.763-770
• /
• 2018

Bioremediation in situ is heavily dependent on the oxygenic environment which would privide the dwelling microorganism with sufficient oxygen. The situation could be easily resolved with supply of an Oxygen Releasing Compound (ORC). In this paper we prepared that sort of material out of oyster shell powder (mostly calcium carbonate) that prevails every shore areas of the country. We used two different oxidizing methods in the first step of the whole manufacturing process-conventional heating in a furnace and an ultrasound generator to obtain calcium oxide. Then that calcium oxide was further oxidized into calcium peroxide which may release oxygen under a moisturized condition. The oxygen releasing experiments were run to test the performance of our products, and to determine the gas kinetics during the experiments. Interestingly, calcium peroxide derived from ultrasound treatment was much more energy-effective as ORC than that from furnace heating although the heat derived process was better than that of ultrasound in terms of oxygen content and its releasing rate. We also found that most of the data collected from the gas releasing experiments fairly supported an ordinary $1^{st}$ order kinetics to oxygen concentration, which shaped a sharp discharge of oxygen at the very early moment of each test.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.7
• /
• pp.871-877
• /
• 2004

In this paper, for manufacturing a custom-made shoes, shape of foot acquired three-dimensional measurement device which makes shoe-last data for needing a custom-made shoes is founded on artificial intelligence technique and it shows method restoring to the original shape in optimized state. the developed system for this study is based on PC which uses existing three dimensional measurement method. And it gains shoe-last and data of foot shape going through 8 CCD(Charge Coupled Device) Which equipped top and bottom, right and left sides and 4 lasers which also equipped both sides and upper and lower sides. The acquired data are processed image processing algorithm using artificial intelligence technique. And result of data management is better quality of removing noise than other system not using artificial intelligence technique and it can simplify post-processing. So, this paper is constituted hardware and software system and it used neural network for determining threshold value, when input image on pre-processing step is being stage of image binarization and present that results.

• KSBB Journal
• /
• v.30 no.3
• /
• pp.109-113
• /
• 2015

Current drying and encapsulation methods for probiotics manufacturing are complicate and cost-burdened processes. The aim of this study was to develop a simple ingredient mixture to make probiotic granules via one-step process, providing not only a cryoprotective effect during freezing and drying but also high survival ratio in gastrointestinal tract. As cryoprotectans, commercially available ingredients including skim milk, monosaccharide (trehalose or glycerin), maltodextrins (with low or high degree of equivalents) were used. Their cryoprotective effect during lyophilization and survival ratios in artificial gastric juice and bile salt were measured against 3 strains of lactic acid bacteria (LAB) (Lactobacillus plantarum, Lb. brevis, and Lactococcus lactis). As results, 3 mixtures with different compositions showed a cryprotective effect on LAB tested and the best compostion was dependant upon LAB; skim milk 10%, trehalose 15%, glycerin 0.5%, and NaCl 1% was for Lb. plantarum and Lc. lactis, and maltodextrin 10% instead of skim milk was for Lb. brevis. In addition, those mixtures showed similar survival effect on LAB tested. These results demonstrate that skim milk or maltodextrins with trehalose, glycerin, and NACl can be effectively used for onestep lyophilization of LAB as an alternative method of encapsulation.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.1
• /
• pp.34-42
• /
• 2015

The paper investigates environmental hazards and characteristics of the artificial lightweight aggregate manufactured by using dyestuff sludge from dyeing industrial complex. The dyestuff sludge used in this study is chemically treated with Ti and Fe salt for the purpose of recycling. The artificial lightweight aggregate is manufactured through 3 step; 1) Selecting the optimum moisture content by evaluating plasticity from the mixing ratio of the clay and sludge, 2) shaping round type based on the optimum mixing ratio, 3) drying and Sintering process. Based on KS F 2534 "Lightweight Aggregate for Structural concrete", the particle size, fineness modulus, the density, absorption, unit volume weight, stability and environmental hazards of the manufactured lightweight aggregate are evaluated. Experimental results show that the particle size and fineness modulus is out of the range. However, it is observed that other physical properties are within criteria. In addition, it is confirmed that the problem of the particle size and fineness modulus could be solved in the manufacturing process.

• Journal of Digital Convergence
• /
• v.12 no.2
• /
• pp.111-117
• /
• 2014

Generally, TPM activity promotion program steps have been determined. However, in order to maximize the efficiency of the production system of TPM, industry types or production methods, equipment type and condition, the problems facing the environment are so different that tips and procedures should be chosen in the right way for each company to promote. This study is aimed at a manufacturing company promoting TPM KSA presented. The TPM activities are broken into two phases. And we employ the AHP method to analyze which phase of activities are more important to recognize than the other phase of activities. In Step 1 of the analysis of TPM activities, promotion improvement is the most important activities of the individual, and the overall activity of the most important activities are the field improvement and loss improvement, then followed by the basic conditions for the preparation and 5S activities to build a system activity, such as the order of the initial cleaning was analyzed.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.2
• /
• pp.203-210
• /
• 2010

For the development of a better product which fits to the target user population, physical workloads such as reach and visibility are evaluated using digital human simulation in the early stage of product development; however, ergonomic workload assessment mainly relies on visual observation of reach envelopes and view cones generated in a 3D graphic environment. The present study developed a quantitative assessment method of physical workload in a digital environment and applied to the evaluation of a Korean utility helicopter (KUH) cockpit design. The proposed assessment method quantified physical workloads for the target user population by applying a 3-step process and identified design features requiring improvement based on the quantified workload evaluation. The scores of physical workloads were quantified in terms of posture, reach, visibility, and clearance, and 5-point scales were defined for the evaluation measures by referring to existing studies. The postures of digital humanoids for a given task were estimated to have the minimal score of postural workload by finding all feasible postures that satisfy task constraints such as a contact between the tip of the index finger and a target point. The proposed assessment method was applied to evaluate the KUH cockpit design in the preliminary design stage and identified design features requiring improvement. The proposed assessment method can be utilized to ergonomic evaluation of product designs using digital human simulation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.6
• /
• pp.365-371
• /
• 2019

In this study, the flame temperature distribution of the diffusion flame burner for SiO₂ deposition was analyzed by the computational fluid analysis. This corresponds to the previous step for simulating the SiO₂ preform deposition process for manufacturing optical fibers using environmentally friendly raw materials. In order to model premixed combustion, heat flow, convection, and chemical reactions were considered, and Reynolds-averaged Navier-Stokes equations and k-ω models were used. As a result, the temperature distribution of the flame showed a tendency to increase the distance from the nozzle surface to the maximum temperature when the flow rate of the auxiliary oxygen increased. In addition, it was confirmed that the temperature distribution due to incomplete combustion was large in the combustion reaction with a large equivalence ratio of the mixed gas.

• Journal of Electrochemical Science and Technology
• /
• v.11 no.1
• /
• pp.60-67
• /
• 2020

In this study, copper (II) oxide powder for electroplating was prepared by recovering CuCl₂ from NaClO₃ type etching wastes via recovered non-sintering two step chemical reaction. In case of alkali copper carbonate [mCuCo₃·nCu(OH)₂], first reaction product, CuCo₃ is produced more than Cu(OH)₂ when the reaction molar ratio of sodium carbonate is low, since m is larger than n. As the reaction molar ratio of sodium carbonate increased, m is larger than n and Cu(OH)₂ was produced more than CuCO₃. In the case of m has same values as n, the optimum reaction mole ratio was 1.44 at the reaction temperature of 80℃ based on the theoretical copper content of 57.5 wt. %. The optimum amount of sodium hydroxide was 120 g at 80℃ for production of copper (II) oxide prepared by using basic copper carbonate product of first reaction. At this time, the yield of copper (II) oxide was 96.6 wt.%. Also, the chloride ion concentration was 9.7 mg/L. The properties of produced copper (II) oxide such as mean particle size, dissolution time for sulfuric acid, and repose angle were 19.5 mm, 64 second, and 34.8°, respectively. As a result of the hole filling test, it was found that the copper oxide (II) prepared with 120 g of sodium hydroxide, the optimum amount of basic hydroxide for copper carbonate, has a hole filling of 11.0 mm, which satisfies the general hole filling management range of 15 mm or less.

• Journal of the Korean Society of Costume
• /
• v.60 no.5
• /
• pp.35-50
• /
• 2010

The purpose of this study was to know how helmet and armor was reinterpreted in historical play by considering general concept and type of old helmet and armor from the aspect of costume history and comparing the helmet and armor types of TV historical plays, Yeongaesomun and Taewangsasingi, whose historical backgrounds were based on the age of Goguryeo. The helmet and armor type shown in Yeongaesomun was reinterpreted as the one, which is close to historical investigation, by reappearing lamellar armor and jongjangpanju(helmet made of slim, long plate) shown in Goguryeo wall painting. The helmet and armor type shown in Taewangsasingi expresses fantastic helmet and armor by adding fantastic factor regardless of historical investigation. The study result reveals that there are several common characteristic factors between the helmet and armors of two historical plays. First, there was a classification in the display of character and story. The helmet and armor type shown in Yeongaesomun classified color and detail design depending on lamellar armor or character. In Taewangsasingi, the helmet and armor was manufactured depending on character's nature and the chain armors, which are lighter than existing helmet and armors, were usual. Second, they escaped from the historical investigation about traditional helmet and armor. In Yeongaesomun, myeonggwangae(a type of armor), which might be popular, was not expressed and Taewangsasingi is free from an imperative idea of historical investigation by manufacturing helmet and armor referring to that of ancient Rome age. The modern sense was reflected to increase dramatic effect. The helmet and armor of Yeongaesomun provides modern feeling by using stainless steel material and modern color arrangement and that of Taewangsasingi is designed in modern, splendid way as it aimed at game development from the planning step.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.355-360
• /
• 2000

There are many changed while a design is completed. Therefore, if the impact of the design changes is estimated, it may result in the improvement of design efficiency. But, the design changes have various types and affect other parts of the design system. Hence, it is difficult to deal with design changes directly. The purpose of this research is to develop a systematic change propagation tracing algorithm and a method of change impact analysis and then, to implement a change impact analysis system. Process based design is set up for the field of this research. Also the design, composed of design parameters and constraints, is set up for the subject of the research. Change propagation tracing algorithm traces change propagation based on the following concept : If the design parameters are changed, other parameters within the constrains including them may be changed. Using the result of change propagation tracing algorithm, changeable parameters, constraints and tasks can be found. The method of change impact analysis, to calculate change impact value from this changeable tasks, is developed. Change propagation tracing algorithm and the method of change impact analysis are implemented into change impact analysis system and it is applied to the redesign of 2 stage gear drives. It can support different kinds of design activities systematically. especially, at the redesign step, where many design change alternatives exist, change impact value of each alternative exist, change impact value of each alternative is calculated and design change is performed toward direction to minimize the impact of design change. Consequently, it is expected to improve the efficiency of the whole design.