• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.38-42
• /
• 1995

In this paper, a theoretical analysis is presented on the mechanics for the side-cut grinding by electrodeposited CBN wheel of a hemispheric type. Each of the grinding force components is calculated by using the geometrical model. It is also presented that experimental results show grinding forces for grinding variable such as wheel speed, feed speed,depth of cut, and grinding wheel positions. The experimental results are found to be in good agreement with those predicted by the analytcal calculation.

• Tribology and Lubricants
• /
• v.9 no.1
• /
• pp.38-44
• /
• 1993

The present study was undertaken to investigate the dry wear characteristics of die steel STD 11 for cold molding. The wear test was experimentally carried out under different conditions using a wear device, which was made in laboratory, and in which annular surfaces of wear testing specimens wear rubbed in dry sliding condition with varying the sliding speed, contact pressure, and sliding distance. The wear loss by variation of sliding speed was much in 0.3 m/sec and less in higher speed range above its sliding speed according to formation of the boundary lubrication film. The critical sliding speed with maximum value of the specific wear rate switched over to lower speed side according. as contact pressure increased. The critical sliding distance was increased with decrease in oxidation reaction velocity. The depth below subsurface showing maximum hardness (Hv) came out at the position, $60 \mu m$, of the maximum shear stress due to strain hardening.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.4 s.235
• /
• pp.614-623
• /
• 2005

This study aims to perform the characteristic evaluation of surface grinding for the STD11 material with experimental and analytic techniques based on the response surface model. The grinding force acting on the workpiece and the ground surface roughness were measured according to the change of grain size, table speed and depth of cut. The effect of spark-out on the grinding force and the surface roughness was also characterized. The frictional coefficient between workpiece and grinding wheel could be determined by the analysis of spark-out effect. From the experimental data, the second-order response surface models were developed to predict the grinding force and the surface roughness. Validation of the developed model was examined.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.380-384
• /
• 1993

In precision wire electrode discharge machining by CAD/CAM, it is the most important problem on machining method to determine the wire electrode offset amout from the accurate calculation of discharge gap in order to increase the machining accuracy, after fixing the main machining conditions such as machining speed, wire tension, coolant conductivity, gap vlotage. The present study shows the relationships between discharge gap and main machining conditions by means of a series of experiment concerned with the gap using the workpiece of STD 11, and suggests the experimental eguation to calculate the accurate wire electrode offset amount under the given machining conditions for spot workers.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.3
• /
• pp.34-40
• /
• 2003

This paper describes evaluation and monitoring methods of machining characteristics for developed micro grooving machine. Experiments were conducted under various process conditions such as spindle revolution speed, feed rates and depth of groove V and U shape of blade and STD11 were used in this experiment. The status of grooving was evaluated through analysis of the Acoustic emission (AE) signal resulted in each process condition. Based on the analysis, this paper examined the possibility of monitoring adapting fuzzy logic. In conclusion, this paper presented the possibility of monitoring in process adapting AE technology and appropriate micro grooving condition.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.4
• /
• pp.23-28
• /
• 2003

This paper describes the machining characteristics of a developed micro grooving machine. Experiments have been conducted on the various grooving condition such as spindle revolution speed, feed rate and depth of groove. V and U-shaped blade tool and STD11 workpiece was used in this study. To evaluate the developed micro grooving machine, AE signal obtained from each experimental condition was analyzed, and cutting stability was compared with the surface state. As a result this study presented the process to optimize grooving condition and possibility of application of AE technique in groove machining.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1105-1108
• /
• 2001

In these days, according s the increase of technological development the part demension goes up for ultra-precision. It is grinding behavior that is important processing which directly influences by machining accuracy at product quality with the net shape manufacturing. In this study, by using CBN wheel an analysis carried out for workpiece's profiles and its characteristics by measuring grinding force and surface roughness. Workpiece materials were used STD11, SUS304 and STB2 varing condition of feedrate and depth of cut.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.927-931
• /
• 1997

In process of the finish face milling of the hardended STD11 steel(H /sab r/ c50,55) by CBN tool, the optimum tool shape is suggested,which can minimize the tool fracture and by chipping by impact. The obtained results are as follows. (1) The optimal chamfer angel was about 25 .deg. , and the suitable chamfer width was 0.2mm. (2) The nose radius of tool was most excellent at 1.2mm in the viewpoint of tool wear and surface roughness. (3) Wear speed was effected by sintering method of CBN tool B.U.E

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.870-874
• /
• 1997

Super-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with resinoid-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance and the surface roughness are measured and discussed. The results are as follows.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.542-546
• /
• 2003

This paper describes the machining characteristics of a developed micro grooving machine. Experiments have been conducted on the various grooving condition such as spindle revolution speed, feed rates and depth of groove. V and U-shaped blade tool and STD11 workpiece was used in this study. Evaluating the machining conditions, RMS and frequency spectrum analysis of AE(acoustic emission) signals according to each conditions were applied. As a result, this study presented the process to optimize micro grooving condition and possibility of application of AE technique in groove machining.