• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.129-134
• /
• 2005

There is a strong industrial demand for the development of light-weight vehicle to improve fuel efficiency and dynamic performance. The effective method of achieving the weight reduction is to use low-density materials such as aluminum and magnesium. In applying these materials to the vehicle, it is often required to join dissimilar materials such as aluminum and steel. However, conventional joining method, namely resistance spot welding cannot be used in joining dissimilar materials. Self·piercing rivet(SPR) and adhesive bonding is a good alternative to resistance spot welding. In this study, the impact test of double hat-shaped member made by resistance spot welding, SPR and adhesive bonding was performed. As a result, various parameters of crashworthiness were analyzed and evaluated. Also, the applicability of SPR and adhesive bonding as an alternative to resistance spot welding was suggested.

• The Korean Journal of Mycology
• /
• v.51 no.4
• /
• pp.277-286
• /
• 2023

Tan spot, caused by Pyrenophora tritici-repentis, is a major foliar disease in wheat worldwide. In April 2021, tan spot symptoms were observed in a commercial wheat field in Suncheon, Jeonnam Province, Korea, with over 5% of the wheat leaves exhibiting symptoms. These symptoms included oval-shaped tan necrosis surrounded by a bright halo. The three representative isolates exhibited irregular mycelial growth on V8-potato dextrose agar and produced pseudothecia. Based on the concatenated sequence datasets of four multi-genes, including the internal transcribed spacer, large subunit ribosomal RNA, glyceraldehyde-3-phosphate dehydrogenase, and RNA polymerase II second-largest subunit genes, phylogenetic analysis revealed that these three isolates clustered in the same clade as P. tritici-repentis. Results of pathogenicity test indicated that the initial symptoms appeared 5 days post-inoculation (dpi), with typical tan spot symptoms developing at 7 dpi. The pathogen was successfully re-isolated from the symptomatic tissues, thus fulfilling Koch's postulates. Furthermore, we selected three fungicides that effectively inhibited the mycelial growth of P. tritici-repentis by more than 90% in vitro. To the best of our knowledge, this is the first report of tan spot disease in wheat in Korea.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.3
• /
• pp.124-139
• /
• 2016

This study was carried out to characterize 127 recently developed cultivars of Rose of Sharon (Hibiscus spp.) in Korea and foreign Countries for landscape uses. The examined factors were growth characteristics such as tree height of a 1-year grafted plant(cm), plant type, growth habit, leaf characteristics such as shape and size, flower characteristics such as color, shape, size, and red eye during 2014 and 2015 for landscape uses. The results are obtained as follows; In the results of flower color of the 127 recently developed cultivars, pink color with red eye spot, white color with red eye spot, purplish red color with red eye spot, violet purple color with red eye spot, crimson color with red eye spot, asadal, blue color with red eye spot, and white color were distributed. In the flower characteristics, Hibiscus hybrid 'Daewangchun' had the largest flower size of 16.0cm out of the 127 cultivars. H. syriacus 'Antong', 'Lil Kim', and 'Ggoma' were cultivars with smaller flowers than other cultivars. H. syriacus 'Hunjang' had largest red eye, of 5.2cm of length compared to the other cultivars. The cultivars with unique flower color for landscape uses are H. syriacus 'Kwangmyung', 'Nanpa', 'North face', 'Bulsae', 'Bidan', 'Songam', 'Youngchang', 'Jukpeoso', 'Kiho', 'Tamla', 'Hwasoored' and 'Hwanhee'. These flowers had a purplish red color and were developed in Korea. H. syriacus 'Aphrodite', 'Dr. Uemoto', 'Freedom', 'Pink Cup', 'PS 80-1', 'Purpureus Variegatus', 'Red Giant', 'Woodbridge' also had unique flowers with a purplish red color and were introduced from foreign countries. In addition, cultivars with violet pink flowers were H. syriacus 'Ggoma', 'Doturak', 'Myungmi', 'Byunghwa', 'Sancheonyu', 'Taehwa', 'Hikari-hanagasa', and 'Little Kim Violet'. 'Jongmoo' and 'Ruffled Satin' had flowers with crimson color. Therefore, the new cultivars with unique flower colors were a promising cultivars to a woody landscape plant. Cultivars with large flower sizes were Hibiscus hybrid 'Daewangchun', Hibiscus hybrid 'Daemang', and Hibiscus hybrid 'Jina'. H. syriacus 'Ggoma', 'Mibeak', 'Antong', 'Lil Kim', and 'Eunhasu' had small flower sizes. Cultivars with long red eye were H. syriacus 'Hunjang' and H. syriacus 'Hi Lea Red'. Therefore, the new cultivars, Hibiscus hybrid 'Daewangchun', Hibiscus hybrid 'Daemang', Hibiscus hybrid 'Jina' with large flower sizes, H. syriacus 'Ggoma', 'Mibeak', 'Antong', 'Lil Kim', and 'Eunhasu' with small flower sizes, H. syriacus 'Hunjang' and H. syriacus 'Hi Lea Red' with long red eye, were promising cultivars to a woody landscape plant.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.10-19
• /
• 1998

The erosion of electrode in spot welding of aluminium alloy by direct current is dependent on the electric polarity. The positive electrode is much more eroded than the negative one. To explain this phenomenon, Peltier effect has been generally accepted as a unique theory. In this study Peltier effect was evaluated by calculations on the basis of some references and experiments. The difference of heat generated by Peltier effect on both electrode surfaces was, however, only 4% of total heat generated during wel- ding. Because of insufficient explanation, Kohler theory, which is mainly affected by thin oxide film, was introduced. A theoretical calculation showed 17% of the temperature difference between the positive and negative electrode, in case "surface voltage" resulted from oxide film was 30% of total contact voltage. This revealed that the erosion of electrode could be more affected by Kohler theory than effect.an effect.

• The Plant Pathology Journal
• /
• v.30 no.4
• /
• pp.440-444
• /
• 2014

Iris yellow spot virus (IYSV) is a plant pathogenic virus which has been reported to continuously occur in onion bulbs, allium field crops, seed crops, lisianthus, and irises. In South Korea, IYSV is a "controlled" virus that has not been reported, and inspection is performed when crops of the genus Iris are imported into South Korea. In this study, reverse-transcription polymerase chain reaction (RT-PCR) and nested PCR inspection methods, which can detect IYSV, from imported crops of the genus Iris at quarantine sites, were developed. In addition, a modified positive plasmid, which can be used as a positive control during inspection, was developed. This modified plasmid can facilitate a more accurate inspection by enabling the examination of a laboratory contamination in an inspection system. The inspection methods that were developed in this study are expected to contribute, through the prompt and accurate inspection of IYSV at quarantine sites to the plant quarantine in South Korea.

• Journal of Power System Engineering
• /
• v.19 no.2
• /
• pp.70-77
• /
• 2015

Nowadays, car manufacturers applied many high strength steels such AHSS or UHSS to car bodies for weight lightening. Therefore, a variety of applied steel sheet to car bodies increased and the needs of simulation to evaluate weldability also increased in order to reduce the cost and time. In this study, resistance spot welding simulations for DP 780 Steel with 1.0 and 1.4 mm thickness were conducted with respect to lobe curve. 2 regression models to estimate tensile shear strength were suggested and they were second order polynomial regression model and optimized second order regression model. The performance of these models was evaluated in terms of the coefficient of determinant and average error rate.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.384-394
• /
• 2002

In this paper, a new control strategy is proposed to improve the quality of the welding products. The conventional nonlinear power control system of spot welders is linearized using nonlinear feedback linearization technique based on differential geometry theory. An evolution strategy(ES) geometry is used to find optimal gain of PI controllers. It tries to find out the optimal control parameters by imitating the natural evolution. Some Simulation and experimental results show that the proposed variable power control system using ES algorithm has better dynamic performances than the conventional one.

• Journal of Welding and Joining
• /
• v.18 no.4
• /
• pp.76-81
• /
• 2000

In this research, various heat source equations that have been proposed in previous study were calculated and compared with new model in various laser parameters. This is to treat the problem of predicting, by numerical analysis, the thermo-mechanical behaviors of laser spot welding for thin stainless steel plates. A finite element code, ABAQUS is used for the heat transfer analysis with a three-dimensional plane assumption. Experimental studies if the laser spot welding have also bee conducted to validate the numerical models presented. The results suggest that temperature profiles and weld dimensions are varied according to the heat source of the laser beam. For this reason, it is essential to incorporate an accurate description of the heat source.

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.147-149
• /
• 2003

Many factors, such as welding current, welding time, force, electrode shape, the output stability of a welding machine, are closely related with micro spot series welding. Of those factors, the output stability evaluation of the welding machine would be checked first. in this study, we applied 6$\sigma$ to evaluation for the output stability of the welding machine. We estimated output stability and control stability of the welding machine by using Cp(process capability), Ppk and 4-block diagram. Therefore the problem as solved in micro spot series welding process and the problem of output control in welding machine by 6$\sigma$ tool.

• Publications of The Korean Astronomical Society
• /
• v.8 no.1
• /
• pp.153-161
• /
• 1993

We analyze 211 data of the daily sunspot observations during the period of January 4 to November 30 in 1993 and present the daily relative sunspot numbers. During 334 days of the period, the preliminary annual average of the relative sunspot numbers is found to be 61.8 based on 27.1 distinct spots in a single group for 3.7 spot groups. According to the appearance of 203 spot groups, our analysis shows that the mean life time of spot group is about 1 day and 15.5 hours. Our records show that more number of sunspots have appeared in the southern hemisphere than in the northern hemisphere by some 2%, indicating that the solar activities of the northern and southern hemisphere are much the same during the period.