• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2000년도 학술대회논문집
• /
• pp.219-224
• /
• 2000

This paper presents a ripple reduction of BLDC motor using TMS320F240. A fault of permanent magnet(PM) BLDC motor possible to miniaturization and high-output is to be difficult to reduce speed-ripple at low speed region. An existing solution is to be use of PWM waveform by PI control with computing control angle of 60$^{\circ}$. The new family of DSP controllers provides a single chip solution by integrating on-chip not only a high computational power but also, all the peripherals necessary for electric motor control. This paper gives an advanced solution of the SVPWM technique for the purpose of reducing control angel rather than 60$^{\circ}$. This technique gives an excellent speed ripple characteristic.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.554-564
• /
• 2002

A newly designed combustion chamber of diesel engine with a modified piston crown was prepared for the purpose of investigation for reduction of NO emission. It was intended to realize 2-stage combustion that is to keep fuel rich condition during early stage of combustion and fuel lean condition during next stage. The engine was tested on various conditions concerning exhaust gas emissions especially about NO emission and simultaneously fuel consumption rate. It was found that the engine with 2-stage combustion type piston emits significantly low NO at various speed and torque compared with conventional engines, but it raised points at issue in CO and smoke emissions with fuel consumption rate. The increasing of injection pressure on 2 stage combustion type diesel engine affects on CO and smoke emission considerably to reduce but slightly on NO to increase. The effect of 2-stage combustion was better at low speed than at high speed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.758-762
• /
• 1998

Many harmonics components are contained within the stator currents of the high-speed synchronous reluctance motor, SynRM, with salient pole rotor. They cause the power factor of SynRM to get worse. In this paper, the mathematical model of SynRM is investigated, and SV_PWM control method is applied to reduce harmonics components in the stator current. Simulation results show the fast response of speed and the reduction of harmonics components at steady state.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.209-214
• /
• 2003

Numerical simulations are performed at atmospheric pressure in order to understand the effect of additives on flame speed, flame temperature, the radical concentration, the NOx formation in freely propagating $CH_4/O_2/N_2$ flames. The additives used are carbon dioxide and hydrogen chloride which have a combination of physical and chemical behavior on hydrocarbon flame. In the flame established with the same mole of methane and additive, $CO_2$ addition significantly contributes toward the reduction of flame speed and flame temperature by the physical effect, whereas addition of HCl mainly does by the chemical effect. The impact of HCl addition on the decrease of the radical concentration is about 1.6-1.8 times as large as $CO_2$ addition. Hydrogen chloride addition is higher on the reduction of EINO than $CO_2$ addition because of the chemical effect of HCl.

• 한국소음진동공학회논문집
• /
• 제17권12호
• /
• pp.1145-1151
• /
• 2007

In this paper, vibration sources of an electric forklift are identified and the forklift vibrations are reduced by structural modification. For vibration identification, vibration signals are measured by an accelerometer when the forklift is moving. These signals are presented in a waterfall plot in order to find the dependency of frequency components on the forklift speed. It is found that main vibration source is tire pattern excitation. From some experiments and finite element analyses, it is also found that resonances occur because the natural frequencies of the forklift exist in usual driving speed range. To shift the natural frequencies outside the driving speed range, the connection parts between main body and loader are modified to increase stiffness. It is verified that considerable amount of vibration are reduced by the structural modification.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.144-151
• /
• 2011

Recent years have witnessed speed up of moving vehicles such as high-speed of trains. Increase in speed entails concomitant increase in turbulent air flow which contributes toward aerodynamic noise. The proposed method for aerodynamic noise reduction is based on a biomimetic design of owl feather. The five morphological parameters of the owl feather is extracted from close observation, and simulation cases are constructed by applying design of experiments methodology. Swirling strength for each case is obtained through steady-state CFD analysis, and key morphological parameters that affect the turbulence are identified. Large eddy simulations (LES) are then performed on selected cases to predict the air turbulence. Different cases show varying vorticity distribution levels which is expected to lead to varying aerodynamic noise levels.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.447-453
• /
• 2012

Nowadays, high speed train has settled down as a fast and convenient environment-friendly transportation and it's need is gradually increasing. However increased train speed leads to increased aerodynamic noise, which causes critically affects comfortability of passengers. Especially, the pantograph of high speed train is protruded out of train body, which is the main factor for increased aerodynamic noise. In this research, to reduce aerodynamic noise pantograph, panhead's shape changed to aerodynamical shape. aerodynamic noise of pantograph is predicted by CFD (Computational Fluid Dynamic) and FW-H (Ffowcs Williams-Hawkings) equation. Also, the sound pressure level of aerodynamic noise of base and modified models are predicted. And the reduction effects of the sound pressure level is analyzed.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권3호
• /
• pp.10-14
• /
• 2014

Due to continuous increase of electric power consumption, couple of resolutions for improving accuracy in power system like line separation are being studied. The increase of the power demand can cause problems such as supply difficulties of the electricity and broadband outages, failure, etc. When a fault occurs in the power system, a fault current also increases. Fault current creates problems like reduction of lifespan and failure on the power system. In order to resolve these problems, the reduction of initial fault current using the characteristics of superconducting element was applied to fault current limiter. We applied the system to high speed fault current limiter. We found that the superconducting element effectively reduced initial fault current and the fault current was limited by changing operation of high speed interrupter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.627-628
• /
• 2006

Miniature BLDC is widely used in industrial applications because of high driving efficiency and high torque characteristic. Otherwise the general BLDC, torque ripple of a high speed miniature BLDC is serous during conduction due to the very low electrical time constant. This paper present instant voltage and current control for torque ripple reduction of a high speed miniature BLDC. Computer simulation and experiment test for 40,000 rpm miniature BLDC show the verification of the proposed control method.

• Journal of Power Electronics
• /
• 제16권6호
• /
• pp.2182-2191
• /
• 2016

This study proposes a novel frame anti-vibration controller for position sensorless PMSM drive application. This controller is called specific component reduction controller (SCRC). SCRC can function without an accelerometer and can achieve speed variable control. This study mainly comprises the following phases. First, the position sensorless control method will be provided. Second, the frame vibration model and load torque ripple will be shown. Third, SCRC will be discussed and its stability will be analyzed. Finally, experimental results show that SCRC can achieve speed variable anti-vibration control and compensate target frequency torque ripple.