• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.118-120
• /
• 2004

Recently 9Cr-1Mo azzoy is used in the Nuclear power plant due to its special properties. This material has the merit of high-strength resistance and corrosion resistance. Therefore the demand for this alloy is dramatically increased in the Nuclear power, petro-chemical complex etc. Re various research has been conducted to improve the material properties of this alloy. In spite of this circumstance, detail research in the area of welding process of this alloy is yet to be expanded In this study the numerical non-linear heat transfer analysis of laser welding which may possibly replace the conventional SMAW fabrication of 9Cr-1Mo steel has been carried out.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.75-85
• /
• 1996

In this paper the influence of postweld heat treatment on mechanical properties of SMAW and FCAW stainless steel weldments was examined and the obtained results are as follows ; (1) The amount of $\delta$-ferrite formed by SMAW and FCAW process decreased with increasing holding temperature and time in post weld heat treatment(PWHT), and it was found that the reduced ferrite was transformed into sigma phase after $800^{circ}C{\times}50hr$ PWHT. This sigma phase, even though it was very small, resulted in brittleness of dissimilar weldment between carbon steel and stainless steel in bending test, however in similar weldment between stainless steel and stainless steel was not occured. (2) The chemical composition of sigma phase was measured to 28-30%Cr, 7-9%Mo, 4-6Ni in 316L weldment, and also 35-37%Cr, 0.9-1.0Mo, 6-8%Ni in 309L weldment by EDS analysis.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.42-44
• /
• 2007

Methods of repair welding are different to production welding for welding position, welding process, welding power source, heating methods. This study investigated proper the welding process used the welding process SMAW and GTAW in the weldment of inconel filler metals. Mechanical test showed that SMAW and GTAW process had higher mechanical properties than those of material specification. Both SMAW and GTAW welding process can appy the repair welding. In comparison, GTAW welding process had more higher mechanical properties in the weldment.

• Journal of Welding and Joining
• /
• 제2권2호
• /
• pp.29-37
• /
• 1984

발전설비를 비롯한 산업설비, 각종 압력용기 및 철구조물 제작시 발생하는 여러가지의 용접불량 중에서 슬래그 혼입이 차지하는 비율이 전체 불량의 절반 이상을 차지하고 있다. 특히 여타의 용접법에 비해 SMAW에 의한 슬래그 혼입의 발생이 가장 많으므로 이에 대한 결함 발생의 경향을 조사하고 그 방지대책을 설정하기 위하여 이번 실험을 실시하게 되었다. 수동 용접봉의 피복제 중 가스 발생 원인은 아아크 분위기를 생성하고 기타 부분은 슬래그가 되어 용융금속을 둘러싸서 이것을 보호하면서 용융지로 이행한다. 슬래그는 용융지 내에서 비이드 표면으로 부상하면서 탈산반응이나 불순물을 제거하는 정련작용을 한다. 또한 적당한 합금 원소의 보충, 용융금속의 유동성 증가 등에 의하여 양호한 용착금속의 생성을 돕는다. 한편, 슬래그는 고온금속을 덮어 이것을 보호함과 동시에 급냉을 완화하는 작용을 한다. 그러나 이러한 슬래그가 응고하는 용착금속 사이에 혼입된다면 용착금속의 기계적 성질을 저하시키는 중요한 요인이 된다. 슬래그 혼입에 대하여 간단하고 일반적인 방지대책은 많이 언급되어 있으나 슬래그 혼입의 방지대책에 대해 깊이 있는 연구가 거의 없다. 이번 실험에서는 광범위한 요인의 선제, 싯수의 제안으로 인하여 새로운 슬래그 혼입 기구의 설정이나 특정한 요인의 영향에 대한 정확한 한계치의 설정보다는 각 요인에 대한 정성적인 영향을 분석하였다.

• Nuclear Engineering and Technology
• /
• 제53권4호
• /
• pp.1357-1368
• /
• 2021

This paper presents thermal aging effect on fracture toughness properties of GTAW (gas tungsten arc welding) and SMAW (shielded metal arc welding) of 316L stainless steels, and investigates the applicability of the existing three thermal aging models for CASS (cast stainless steels). Thermal aging was carried out at 350 ℃ for up to 15,000h and at 400 ℃ up to 8,000h. After aging, tensile and fracture toughness tests using 0.5T C(T) specimens were carried out at room temperature and at 288 ℃. Comparing with the predictions using three (ANL, French and H3T) thermal aging models for CASS show that the predictions can be very non-conservative at operating temperature, and thus that the existing thermal aging models for CASS cannot be applied to the welded stainless steels.

• Journal of Welding and Joining
• /
• 제31권1호
• /
• pp.11-20
• /
• 2013

Recent developing tendency of overlay welding on welding methods are studied by searching of NDSL, ScienceDirect and KIPRIS. PTA, Laser cladding, SMAW, GTAW, GMAW, SAW and ESW are selected as welding methods. Development and improvement of various new overlay welding processes and technology are introduced, especially PTA and Laser cladding in abroad overlay welding technology are activated substantially.

• Journal of Welding and Joining
• /
• 제16권4호
• /
• pp.125-135
• /
• 1998

The shielded metal arc welding (SMAW) by AC power source was performed to evaluate the arc stability by arc monitoring and analysing. In this study, the arc stability index was evaluated quantitatively by using he coefficient of resistance variation for welding time. This coefficient was obtained for the long time (20sec.) by analysing the waveforms of welding current, voltage and resistance. The coefficient was applied to indicate numerically the variation level of arc length and the degree of arc extinction. Using the coefficient of resistance variation in practical welding, the arc stability of the high titanium oxide electrode (KS E4313) turned out to be better than that of the low hydrogen electrode (KS E4316). In evaluating the skill level of welders by the coefficient, the horizontal fillet weaving welding became clear to be very discriminating because the higher level welder could weave in keeping constant arc length, but the lower level welder showed the characteristics of weaving with the unstable arc length. And it was confirmed that the welding defects as blow holes was formed when the arc stability index were high.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.385-393
• /
• 2007

The strength evaluation of the most weakest junction part is required for the safety design of all structures. Most of all. in order to enhance the reliability and safety of the welding part. whose use is the highest, it is very important to establish the efficient structure manufacturing technology by studying and investigating the evaluation of fatigue strength in various environments. This study analyzed the relations of da/dN, and th according to the welding methods of SMAW, FCAW, and SAW. In the stage II. the value of stress intensity factor range was the highest in SMAW welding method of stress ration R=0.1, and appeared under the sequence of FCAW and SAW and as the completion section of stress intensity factor was low, threshold stress intensity factor was lowly formed in da/dN - The fatigue life of each welding method is sensitively worked in high stress ratio. judging from the fact that the width of life reduction increases in the high stress ratio zone compared to the width of life reduction in the low stress ratio zone. In the fatigue limit of welding methods before corrosion. the welding of SMAW and FCAW shows the same fatigue limit compared to Base metal, and SAW holds the lowest fatigue limit value.

• 국방과기술
• /
• 7호통권197호
• /
• pp.9-9
• /
• 1995

• 한국환경보건학회지
• /
• 제30권4호
• /
• pp.320-328
• /
• 2004

A number of health hazards are generated in welding processes. In this paper, the characteristics of fumes and some other hazardous agents in welding are reviewed. Fumes in welding are generated by complex mechanism like physical ejection of particles, oxidation-enhanced vaporization, vaporization-condensation-oxidation, and spatter contribution. Fume generation rates could be described as a power function in a given process. Most of fume constituents was originated from consumables rather than base metal. The mass distribution for the welding fumes is unimodal and very small to penetrate respiratory system. So, almost fractions of fumes are classified into the respirable particulate mass. Total chromium contents in FCAW were similar to those from SMAW whereas hexavalent chromium concentrations in fume were similar to those produced from MIG welding fume. Hexavalent chromium was mostly soluble which was similar to the characteristic solubility of fume hexavalent chromium from SMAW.