• Journal of the Earthquake Engineering Society of Korea
• /
• v.16 no.6
• /
• pp.1-12
• /
• 2012

The researches related to active control systems utilizing superelastic shape memory alloys (SMA) have been recently conducted to reduce critical damage due to lateral deformation after severe earthquakes. Although Superelastic SMAs undergo considerable inelastic deformation, they can return to original conditions without heat treatment only after stress removal. We can expect the mitigation of residual deformation owing to inherent recentering characteristics when these smart materials are installed at the part where large deformation is likely to occur. Therefore, the primary purpose of this research is to develop concentrically braced frames (CBFs) with superelastic SMA bracing systems and to evaluate the seismic performance of such frame structures. In order to investigate the inter-story drift response of CBF structures, 3- and 6-story buildings were design according to current design specifications, and then nonlinear time-history analyses were performed on numerical 2D frame models. Based on the numerical analysis results, it can be comparatively verified that the CBFs with superelastic SMA bracing systems have more structural advantages in terms of energy dissipation and recentering behavior than those with conventional steel bracing systems.

• Journal of Welding and Joining
• /
• v.34 no.5
• /
• pp.33-40
• /
• 2016

The microstructures and the creep rupture properties of dissimilar welds between the Ni-based superalloy Inconel 740H and the non-stabilized austenitic stainless steel TP316H have been characterized. The welds were produced by shielded metal arc (SMA) welding process with the AWS A5.11 Class ENiCrFe-3 filler metal, commonly known as Inconel 182 superalloy. Postweld heat treatment at $760^{\circ}C$ for 4 hours was conducted to form ${\gamma}^{\prime}$ strengthener in Inconel 740H. The austenitic weld metal produced by Inconel 182 had a dendritic microstructure, and grew epitaxially from the both sides of Inconel 740H and TP316H base metals. Since both Inconel 740H and TP316H did not undergo any solid-state transformation during welding process, there were no heat-affected-zone (HAZ) sub-regions and the coarsoned grains near the weld interface were limited to a narrow region. The hardness of Inconel 182 weld metal was ~220 Hv. The gradual hardness decrease was detected at HAZ of TP316H, and the TP316H base metal displayed the lowest hardness value (~180 Hv) whilst the Inconel 740H showed the highest hardness value (~400 Hv). Fracture after creep occurred at the center of weld metal, regardless of creep condition. It was found that during creep the cracks initiated and propagated along interdendritic regions and grain boundaries at which Laves particles enriched in Nb, Si and Cr were present. The appropriate design of weld metal was discussed to suppress the creep-induced cracking of the present dissimilar weld.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1232-1235
• /
• 2005

In recent years, as the robot technology is developed the researches on the artificial muscle actuator that enable robot to move dextrously like biological organ become active. The widely used materials for artificial muscle are the shape memory alloy and the electroactive polymer. These actuators have the higher energy density than the electromechanical actuator such as motor. However, there are some drawbacks for actuator. SMA has the hysterical dynamic characteristics. In this paper the segmented binary control for reducing the hysteresis of SMA is proposed and the simulation of anthropomorphic robotic hand is performed using ADAMS.

• Korean Journal of Radiology
• /
• v.22 no.11
• /
• pp.1909-1917
• /
• 2021

Objective: Muscle quantity and quality can be measured with an automated system on CT. However, the effects of contrast phases on the muscle measurements have not been established, which we aimed to investigate in this study. Materials and Methods: Muscle quantity was measured according to the skeletal muscle area (SMA) measured by a convolutional neural network-based automated system at the L3 level in 89 subjects undergoing multiphasic abdominal CT comprising unenhanced phase, arterial phase, portal venous phase (PVP), or delayed phase imaging. Muscle quality was analyzed using the mean muscle density and the muscle quality map, which comprises normal and low-attenuation muscle areas (NAMA and LAMA, respectively) based on the muscle attenuation threshold. The SMA, mean muscle density, NAMA, and LAMA were compared between PVP and other phases using paired t tests. Bland-Altman analysis was used to evaluate the inter-phase variability between PVP and other phases. Based on the cutoffs for low muscle quantity and quality, the counts of individuals who scored lower than the cutoff values were compared between PVP and other phases. Results: All indices showed significant differences between PVP and other phases (p < 0.001 for all). The SMA, mean muscle density, and NAMA increased during the later phases, whereas LAMA decreased during the later phases. Bland-Altman analysis showed that the mean differences between PVP and other phases ranged -2.1 to 0.3 cm² for SMA, -12.0 to 2.6 cm² for NAMA, and -2.2 to 9.9 cm² for LAMA.The number of patients who were categorized as low muscle quantity did not significant differ between PVP and other phases (p ≥ 0.5), whereas the number of patients with low muscle quality significantly differed (p ≤ 0.002). Conclusion: SMA was less affected by the contrast phases. However, the muscle quality measurements changed with the contrast phases to greater extents and would require a standardization of the contrast phase for reliable measurement.

• The Journal of Korea Robotics Society
• /
• v.8 no.2
• /
• pp.136-142
• /
• 2013

In nature, many small insects are using jumping as a survival strategy. Among them, fleas jump in a unique method. They use an elastomer, 'Resilin', an extensor muscle and a trigger muscle. By contracting the extensor muscle, the elastic energy, that makes a flea to jump, is stored in the resilin. After storing energy, the trigger muscle begins contracting and pulling the extensor muscle. When the extensor muscle crosses the rotational joint, direction of torque generated from the extensor muscle reverses, 'torque reversal mechanism'. Simultaneously, the elastic energy stored in the resilin releases rapidly and is converted into the kinetic energy. It makes a flea to jump 150 times its body length. In this paper, miniaturized jumping robot using flea-inspired catapult mechanism is presented. This mechanism is based on the 4-bar linkage and the reversal joint and is actuated by Shape Memory Alloy (SMA) coiled springs describing the flea's muscle. The robot prototype is fabricated by SCM process using glass fiber prepregs and a sheet of polyimide film. The prototype is 20mm link length, 34mm width and 2.0g weight and can jump 103cm.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.232-240
• /
• 2012

Bio-diesel (BD) is the mono alkyl esters of long chain fatty acids derived from renewable feed stocks like vegetable oils or animal fats. Bio-diesel shows poorer fuel properties than that of diesel fuel in a cold condition. For the diesel fuel, many cold flow improvers have been developed; however, since primary ingredients of bio-diesel are different from those of the diesel fuel, there is a limit to the cold flow improvement when the same cold flow improvers are added to bio diesel. In this study, to improve low temperature properties of bio-diesel, we developed a cold flow improver using an alkyl methacrylate monomer, prepared via ester reaction, and maleic anhydride and also conducted a ring opening reaction using amine. We characterized the products using $^1H-NMR$, FT-IR and GPC methods. In addition, the cold flow improvements of the products in Soybean BD and Palm BD in the concentration rage of 1000~10000 ppm were investigated. It was found that the addition of LMA2SMA6MA2-C8A in Soybean BD improved the pour point by $12.5\;^{\circ}C$.

• Smart Structures and Systems
• /
• v.4 no.2
• /
• pp.137-152
• /
• 2008

The work presented in this paper includes material characterisation and an investigation of suitability in seismic dampers for two commercially available NiTi-alloys, along with a numerical analysis of a new damper system employing composite NiTi-wires. Numerical simulations of the new damper system are conducted, using Brinson's one-dimensional constitutive model for shape memory alloys, with emphasis on the system's energy dissipation capabilities. The two alloys tested showed some unwanted residual strain at temperatures higher than $A_f$, possibly due to stress concentrations near inclusions in the material. These findings show that the alloys are not ideal, but may be employed in a seismic damper if precautions are made. The numerical investigations indicate that using composite NiTi-wires in a seismic damper enhances the energy dissipation capabilities for a wider working temperature range.

• Journal of Gastric Cancer
• /
• v.20 no.3
• /
• pp.256-266
• /
• 2020

Purpose: This study aimed to examine the early postprandial changes in gastrointestinal (GI) hormones and hemodynamics in terms of early dumping syndrome after gastrectomy for gastric cancer. Materials and Methods: Forty patients who underwent gastrectomy for gastric cancer and 18 controls without previous abdominal surgery were enrolled. Before and 20 minutes after liquid meal ingestion, blood glucose, glucagon-like peptide-1 (GLP-1), and GLP-2 concentrations and superior mesenteric artery (SMA) and renal blood flow were measured. The patients' heart rates were recorded at 5-minute intervals. All subjects were examined for dumping syndrome using a questionnaire based on Sigstad's clinical diagnostic index. Results: The postprandial increases in blood glucose, GLP-1, and GLP-2 levels as well as SMA blood flow and heart rate were greater in patients who underwent gastrectomy than in controls (all P<0.010). Patients who underwent gastrectomy showed a significantly decreased renal blood flow (P<0.001). Among patients who underwent gastrectomy, distal gastrectomy was a significant clinical factor associated with a lower risk of early dumping syndrome than total gastrectomy (hazard ratio, 0.092; 95% confidence interval, 0.013-0.649; P=0.017). Patients who underwent total gastrectomy showed a greater postprandial increase in blood glucose (P<0.001), GLP-1 (P=0.030), and GLP-2 (P=0.002) levels as well as and heart rate (P=0.013) compared to those who underwent distal gastrectomy. Conclusions: Early postprandial changes in GI hormones and hemodynamics were greater in patients who underwent gastrectomy than in controls, especially after total gastrectomy, suggesting that these changes play a crucial role in the pathophysiology of early dumping syndrome.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1099-1107
• /
• 2013

This study proposes a weight reduction design for urban transit, specifically, a Korean EMU carbody made of aluminum extrusion profiles, according to size optimization and useful material changes. First, the thickness of the under-frame, side-panels, and end-panels were optimized by the size optimization process, and then, the weight of the Korean EMU carbody could be reduced to approximately 14.8%. Second, the under-frame of the optimized carbody was substituted with a frame-type structure made of SMA 570, and then, the weight of the hybrid-type carbody was 3.8% lighter than that of the initial K-EMU. Finally, the under-frame and the roof-panel were substituted with a composite material sandwich to obtain an ultralight hybrid-type carbody. The weight of the ultralight hybrid-type carbody was 30% lighter than that of the initial K-EMU. All the resulting carbody models satisfied the design regulations of the domestic Performance Test Standard for Electrical Multiple Unit.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.113-123
• /
• 2011

LCC analysis is a method that coordinates with function evaluation for value improvement, rather than a separate one for cost evaluation. Although its accuracy is rising, materials and structural types developed or applied relatively recently have yet to obtain a sufficient maintenance profile DB, inducing reliability to reduce from difficulties in estimating maintenance records. Based on the above mentioned background, this paper presents the LCC methodology of coordinating functional intensification matters with cost for analysis on alternatives with difficulties in setting maintenance profile. Recently, steel plate bridge deck pavements are faced with problems such as plastic deformation due to the increase in heavy vehicles and traffic, promoting the development of a new compound pavement. This paper execute LCC analysis by mentioning case studies of SMA, Guss and PSMA pavements to include performance scale compared between alternatives as relative evaluation coefficients into the maintenance profile.