• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.761-766
• /
• 2011

In this study, the optimized design profiles between a seal ring and a seal seat of contacting seal units has been proposed based on the FEM computed results. The maximum temperatures, the thermal distortions in axial and radial directions, and maximum contact normal stresses between a seal ring and a seal seat have been analyzed for various contact sealing profiles. The FEM computed results present that the contact area between seal rings and seal seats is very important for a good tribological performance such as low friction heating, low wear, high contact normal stress in a primary sealing components. The seal surface model III in which has a small sealing contact area shows low dilatation of primary sealing components, and high contact stress between a seal ring and a seal seat. This model with small contact surface of a seal ring produces high friction heating and contact stress. But the model III produces very small deformations of contacting sealing surface because of high convection heat transfer by cooling water circulation around the seal ring surface. Thus, the analysis results recommend a short width of a primary sealing unit rather than a big width of contact surfaces of contacting seal units for reducing a leakage and axial deformation of primary seal components.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.119-126
• /
• 2006

In this paper, the contact behavior characteristics of a primary sealing components such as a seal ring and a seal seat has been presented for a small hydro-power turbine. Using the non-linear FEM analysis, the maximum temperature, the axial displacement, radial differences between a seal ring and a seal seat, and maximum contact normal stress have been analyzed for three optimized sealing profiles in which are designed based on the FEM analysis and Taguchi's experimental method. The three primary sealing profiles between a seal ring and a seal seat are strongly related to a leakage of a water for a hydro-power turbine and wear of a primary sealing component. The computed results show that the contact rubbing area between a seal ring and a seal seat is very important for reducing a friction heating and wear in a sealing gap, and increasing a contact normal stress in primary sealing components. Based on the FEM computation, models II and III in which have a small rubbing surface of seal rings show low dilatation of primary sealing components, and high normal contact stress between a seal ring and a seal seat. Thus, the FEM computed results recommend a short contacting width of a primary sealing component for reducing a leakage and thermal distortions, and expanding a seal life. This means that a conventional primary sealing component may be switched to a reduced sealing face of seal rings.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.341-349
• /
• 2001

Heat distortion of the non-contacting mechanical face seal is affected by friction heat between primary seal and seal sheet. The fluid or gas in mechanical face seal maintains operating gap, cooling friction heat and lubricates at the face of seal. So we designed face of seal for inclined face. inclined face of seal improves fluid or gas flow at the face of seal and it increases circumferential velocity at outer radius of the seal so temperature of the seal is decreased by low heat transfer coefficient at there. In this paper, inclined face seal are analysed numerically using finite element method for proof improve inclined face seal performance. Angle of the incline face used for FEA is from 50$^{\circ}$to 90$^{\circ}$and for explaining the effects of inclined face in seal, we get temperature, face distortion, and stress in the seal with variable operating gap and rotating speeds. Result of analysis shows that angle of the incline face is 60$^{\circ}$come to good thermal distortion characteristics.

• International Journal of Advanced Culture Technology
• /
• 제10권4호
• /
• pp.219-225
• /
• 2022

In November 1983, Deng Sanmu's wife, Zhang Jianquan, donated a large number of Deng Sanmu's original seal carving stones and seal cutting scores to the Heilongjiang Provincial Museum in China. Therefore, the Heilongjiang Provincial Museum of China is the richest and most authoritative place to collect Deng Sanmu's original seal cutting stones and seal carving scores. According to the fieldwork, the original seal cutting stones and the seal cutting score donated by Deng Sanmu's wife, Zhang Jianquan, include Deng Sanmu's seal cutting inscriptions made between 1922 and 1963. In addition, Deng Sanmu's own life and career in the art are documented in detail in his markings, so the seal cutting inscriptions of Deng Sanmu in the collection of the Heilongjiang Provincial Museum of China are quite representative. We paper is a documentary review and study of the seal inscriptions of Deng Sanmu in the collection of the Heilongjiang Provincial Museum in China. For the accuracy and richness of this study, a total of 89 representative seals in the collection are used as primary sources to study Deng Sanmu's seal cutting emulation method. The specific content is centered on ancient seals, Qin seals, and Han seals, from which the lineage of Deng Sanmu's emulation methods of seal cutting is further clarified.

• 한국유체기계학회 논문집
• /
• 제9권3호
• /
• pp.14-21
• /
• 2006

Leakage reduction through annular type seals of turbomachinery is necessary for enhancing their efficiency and the precise prediction method of seal leakage is needed. The analysis based on Bulk-flow concept has been mainly used in predicting seal leakage. However, full Navier-Stokes Equations with turbulent model derived in the seal flow passage have to be solved for improving the prediction of seal leakage. FLUENT 6 which is commercial CFD(Computational Fluid Dynamics) code based on FVM(Finite Volume Method) and SIMPLE algorism has been used to analyze leakage of various non-contact-type seals in this presentation. Comparing with the results of Bulk-flow model analysis and experiment, the result of CFD analysis shows good agreement with that of existing theoretical analysis for the incompressible grooved seal and compressive plain and staggered seal. The CFD analysis also shows improvement on the leakage prediction of the incompressible plain seal and compressive see-through-type labyrinth seal.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.88-94
• /
• 2006

A typical disk brake system consists of caliper housing, piston, seal and two pads etc. The configuration of seal groove, dimension of piston and seal, and seal material properties are important ones for brake performance, as these affect the retraction of piston. The rubber seal is designed to perform dual functions of sealing the brake oil at brake-applied and retracting the caliper piston at brake-released. In this paper, the seal stress is analyzed using Finite Element Method and experiment is conducted by Taguchi's Method. We attempt to quantify the critical design factors in the seal groove and evaluate their impact on some of brake performance factors. The investigation obtained from this study can not only enhance the seal groove design optimization, but also reduce product prototype testing and development time.

• Tribology and Lubricants
• /
• 제20권4호
• /
• pp.183-189
• /
• 2004

The floating ring seal is used in an oxidizer and a fuel pump of the turbo pump unit in the liquid rocket engine to optimize a leakage without rubbing phenomenon. The damper floating ring seal, one of the floating ring seals, is with round hole pattern surfaces. It can reduce the leakage by increased friction factor that obtained from experimental data. In this paper, the leakage test about floating ring seal and damper floating ring seal was conducted. The test result showed the leakage performance of damper floating ring seal was better than the leakage performance of floating ring seal. With the leakage test the lock-up and rotation test about seal was conducted and that position is measured. The relatively large lock-up eccentric ratio was obtained from the test result of damping floating ring seal. The attitude angle of seal increases with increasing of shaft rotation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.820-825
• /
• 2004

The floating ring seal is used in an oxidizer and a fuel pump of the turbo pump unit in the liquid rocket engine to optimize a leakage without rubbing phenomenon. The damper floating ring seal, one of the floating ring seals, is with round hole pattern surfaces. It can reduce the leakage by increased friction factor that obtained from experimental data. In this paper, the leakage test about floating ring seal and damper floating ring seal was conducted. The test result showed the leakage performance of damper floating ring seal was better than the leakage performance of floating ring seal. With the leakage test the lock-up and rotation test about seal was conducted and that position is measured. The relatively large lock-up eccentric ratio was obtained from the test result of damping floating ring seal. The attitude angle of seal increases with increasing of shaft rotation

• Tribology and Lubricants
• /
• 제25권3호
• /
• pp.150-156
• /
• 2009

Precise leakage prediction for annular type seals of turbomachinery is necessary for enhancing their efficiency and various prediction methods have been developed. As the seal passage is designed intricately, the analysis based on Bulk-flow concept which has been mainly used in predicting seal leakage is limited. In order to improve the seal leakage prediction, full Navier-Stokes Equations with turbulent model derived in the seal flow passage have to be solved. In this study, 3D CFD (Computational Fluid Dynamics) analysis has been performed for predicting leakage of various non-contact type anular seals using FLUENT. Compared to the results by Bulk-flow model analysis, experiment, and 2D CFD analysis, the result of 3D CFD analysis shows improvement in predicting seal leakage, especially for the parallel grooved pump seal.

• 한국기계가공학회지
• /
• 제15권4호
• /
• pp.118-124
• /
• 2016

In this paper, the model to develop the forming process for turbine seal is suggested. And numerical approach for the shape design of the turbine seal is examined. Because of the thin thickness of the turbine seal, the seal is easily fractured in the manufacturing process. The main factors of the seal manufacturing consist of addendum angle and dedendum angle, fillet on the addendum face, number of the gear teeth, sheet initial location and gear initial location, rake and vertical clearance. The structure and shape of seal are modeled using the commercial 3D mechanical design program, CATIA(V5/R20). Also, rolling process to manufacture the turbine seal is analyzed using DEFORM$^{TM}$-3D(V11), commercial forming analysis software and runs under PC workstation. This study focused on the shape design of turbine seal. Through this research, the main factors to make the turbine seal for airplane turbine engine can be obtained. This study results are reflected to the shape design for turbine seal.