• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.36 no.4
• /
• pp.153-161
• /
• 2020

This study investigates the recycling potential of demolition waste (DW) according to building structure, while considering economic aspects. For that, this study surveyed 1,034 residential buildings to collect reliable information on demolition waste generation rates (DWGRs). This study suggested a method for operational cost calculation for each stage and carried out an inventory analysis. The economic value of recycled DW materials was also calculated. And then, the recycling potential(RP) was calculated by building structures and waste types. RP by building structure was low (27-40%), and RP was found in the order of masonry-block, wooden, RC and concrete-brick. By type of DWs, the RP of aggregates was considerably lower than 7%, and DWs such as wood, plastics, and metals showed more than 100% RP. Considering the results of this study, In order to improve the RP of buildings and DWs, the diversification of products that recycled waste like aggregates (i.e., mortar, concrete, bricks, blocks, tiles) and the development of high value-added products are considered to be the most urgent problems. Based on the above RP results, this study proposed a more advanced method for life cycle assessment of buildings and demolition waste.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.9
• /
• pp.199-206
• /
• 2019

Experimental study on the durability characteristics to examine the feasibility of concrete with high water-tightness and self-healing performance to minimize maintenance of concrete for artificial ground is as follows. 1) When blending agent, swelling agents, and curing accelerator were added on the ternary system cement with blast-furnace slag fine particles and fly ash to give a self-healing property, higher blending strengths by 82% at design standard strength of 24MPa and by 74% at design strength of 30MPa, respectively could be obtained. 2) The permeability test for the specimens having high water-tightness and no shrinkage showed that the permeability was reduced at maximum of 98%. However, the permeability was decreased as the design strength was increased, showing the reduction rate of 87% at the design strength of 50MPa. 3) The depth of carbonation of blast-furnace slag and fly ash was increased in all the specimens compared with those of OPC only. However, as the material age was increased, carbonation penetration depth was decreased compared with the reference blend. 4) Compared with the reference blending using only OPC, the freeze-thaw resistance was higher in the case of blending with 40% of blast-furnace slag and 10% of fly ash at the design standard strength of 50MPa. In addition, the freeze-thaw resistance in general was superior in the design standard strength of 50MPa with the lower water-binder ratio (W/B) as compared with the design standard strength of 24MPa and 30MPa with the high water-binder ratios.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.2
• /
• pp.57-66
• /
• 2018

When developing projects to build facilities to be shared by both military bases and surrounding communities, strategies are needed to achieve two objectives: 1) minimize missteps and opposition from local communities in the process of developing and implementing such projects, and 2) promote cost-benefit optimization and user-satisfaction. With aim of promoting co-operation and co-existence between military bases and adjust communities, this research proposes esthetical factors to be considered in conceiving civil-military sharing facilities. It seeks experts' opinions on the development of civil-military sharing facilities, and examines critical factors (economic feasibility, security, and satisfaction, etc.) for project development as well as building types suitable for shared-use between military bases and local residents. It then establishes a method to prioritize facility-type and narrow down design factors (considerations and restrictions) in project development by applying quantitative analysis. The methodological approach of the research employs the Delphi survey method to quantitatively analyze qualitative information drawn from experts' opinions. At the first round of the survey, facility types, items for consideration and restrictions are drawn, and then at the second round of the survey, criticality of each item is analyzed. Finally, it reaches a conclusion on suitability of facility types for civil-military sharing facilities, and selects project considerations and restrictions when developing this kind of project.

• Journal of Naturopathy
• /
• v.10 no.2
• /
• pp.71-76
• /
• 2021

Background: The understanding of back-pain as one of the commonest clinical presentations, made the path to the present study. More than three-quarters of the world's population experience back-pain at some time in their lives Purpose: The present study has evaluated the selected Naturopathic therapeutic procedures on individuals with low back-pain. Methods: Thirteen patients were selected for the study and randomly divided into two groups, viz., Group A, Naturopathic group and Group B, Control group. One patient discontinued. Naturopathic group was treated with mud pack, aromatherapy massage with Eucalyptus oil, acupressure, steam, wet trunk pack, exercises, relaxation and breathing exercises. Advice for life style and diet was given for patients of both the groups. The effect of the therapy was assessed subjectively and objectively. Particular scores drawn for Naturopathic group and control group were individually analyzed before and after treatment and the values were compared using standard statistical protocols. Results: Naturopathic intervention revealed 100% relief in both subjective and objective parameters (i.e., 6 out of 14 parameters showed statistically highly significant P < 0.01 results, while 8 showed significant results P < 0.05). Conclusion: Statistically highly significant results of this study point out the successful management of the multi factorial low back-pain with a multi focused Naturopathic treatment approach. Such encouraging results may pave the way for a future study on a large sample in a longer duration incorporating clinical investigations.

• Korean journal of applied entomology
• /
• v.60 no.2
• /
• pp.229-234
• /
• 2021

This study investigated spray patterns and coverage generated by three types of commercial nozzles for spraying pesticides with Unmanned Aerial Vehicles (UAVs) using a multi-copter. Flufenoxuron+metaflumizone SC and bifenthrin EC were sprayed. The falling particles of the spraying agent were measured using WSP (Water and oil Sensitive Paper) and the coverage was determined. The results showed that the uniformity of falling particles was different according to the difference in wind strength, and there was no difference for different formulations. The injection amount for each nozzle was found to be different from the official information provided by the manufacturers. These results could be used to establish guidelines for the control of UAVs and pesticide registration testing.

• Korean Journal of Materials Research
• /
• v.32 no.5
• /
• pp.243-248
• /
• 2022

This study demonstrates a different approach method to fabricate antimony selenide (Sb₂Se₃) thin-films for the solar cell applications. As-deposited Sb₂Se₃ thin-films are fabricated via electrodeposition route and, subsequently, annealed in the temperature range of 230 ~ 310℃. Cyclic voltammetry is performed to investigate the electrochemical behavior of the Sb and Se ions. The deposition potential of the Sb₂Se₃ thin films is determined to be -0.6 V vs. Ag/AgCl (in 1 M KCl), where the stoichiometric composition of Sb₂Se₃ appeared. It is found that the crystal orientations of Sb₂Se₃ thin-films are largely dependent on the annealing temperature. At an annealing temperature of 250 ℃, the Sb₂Se₃ thin-film grew most along the c-axis [(211) and/or (221)] direction, which resulted in the smooth movement of carriers, thereby increasing the carrier collection probability. Therefore, the solar cell using Sb₂Se₃ thin-film annealed at 250 ℃ exhibited significant enhancement in J_SC of 10.03 mA/cm² and a highest conversion efficiency of 0.821 % because of the preferred orientation of the Sb₂Se₃ thin film.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.9-9
• /
• 2023

하천의 관리 및 활용을 위해서는 하천의 유량, 수심, 유속과 같은 수리량을 측정하고 모니터링하는 것은 매우 중요하다. 이러한 수리량은 측정하는 방법은 직접 측정하는 방법과 구조물을 이용하여 측정하는 방법이 있으며, 직접 측정하는 방법도 지점 유속을 측정하여 도섭법으로 측정하는 방법, 초음파 방식 도플러 유속계를 이용한 횡단 측정방법 및 특정 수심에서 측정한 유속을 이용하여 지표유속법으로 유량을 산정하는 방법 등이 있다. 또한 '수자원의 조사·계획 및 관리에 관한 법률' 제11조제1항에 따르면 수문조사의 방법·기준 및 수문조사 자료의 처리·활용 방법 등은 표준화해야 한다고 명시되어 있다. 정부에서는 WTO의 TBT협정 등 국제규범에 대응하기 위하여 국제표준인 ISO, IEC 등에 부합하는 국가표준운영체계를 유지하기 위하여 여러 분야의 국제 표준에 대한 대응을 수행하고, 국가표준을 관리하고 있다. 그 중 유량측정과 관련된 국가 및 국제 표준은 2018년부터 환경부 국립환경과학원에서 총괄하고, 한국건설기술연구원과 한국수자원공사에서 표준관리를 위한 표준개발협력기관과 국제표준 대응협력을 위한 ISO 국내 간사기관으로 운영되고 있다. 국가표준의 유량분야(TC 113)는 4개의 세부분과위원회(SC)로 구성되어 있고, 하천에서 수행되는 유량, 수심, 유속 측정 및 측정장비의 검정, 강수량 측정기기 등에 대한 39종이 제정되고 관리하고 있다. 한국건설기술연구원에서는 유량분야의 일반사항, 하천에서의 유량측정방법 및 유량측정기기에 관한 표준을 담당하고 있으며, 유량분야의 국제표준의 개발에 관한 과업을 수행하고 있다. 본 발표에서는 한국건설기술연구원에서 관리하는 유량분야 국가표준 및 국제표준의 종류 및 현업에서 수행중인 하천의 유량 측정과 국가표준의 관계에 대하여 설명하고자 한다.

• International Journal of Computer Science & Network Security
• /
• v.24 no.6
• /
• pp.200-206
• /
• 2024

Laser induced breakdown spectroscopy (LIBS) technique has been used for the elemental composition of the soils. In this technique, a high energy laser pulse is focused on a sample to produce plasma. From the spectroscopic analysis of such plasma plume, we have determined the different elements present in the soil. This technique is effective and rapid for the qualitative and quantitative analysis of all type of samples. In this work a Q-switched Nd: YAG laser operating with its fundamental mode (1064 nm laser wavelength), 5 nanosecond pulse width, and 10 Hz repetition rate was focused on soil samples using 10 cm quartz lens. The emission spectra of soil consist of Iron (Fe), Calcium (Ca), Titanium (Ti), Silicon (Si), Aluminum (Al), Magnesium (Mg), Manganese (Mn), Potassium (K), Nickel (Ni), Chromium (Cr), Copper (Cu), Mercury (Hg), Barium (Ba), Vanadium (V), Lead (Pb), Nitrogen (N), Scandium (Sc), Hydrogen (H), Strontium (Sr), and Lithium (Li) with different finger-prints of the transition lines. The maximum intensity of the transition lines was observed close to the surface of the sample and it was decreased along the axial direction of the plasma expansion due to the thermalization and the recombination process. We have also determined the plasma parameters such as electron temperature and the electron number density of the plasma using Boltzmann's plot method as well as the Stark broadening of the transition lines respectively. The electron temperature is estimated at 14611 °K, whereas the electron number density i.e. 4.1 × 10¹⁶ cm^-3 lies close to the surface.

• Food Science of Animal Resources
• /
• v.44 no.3
• /
• pp.710-722
• /
• 2024

Extracellular matrix (ECM) proteins play a crucial role in culturing muscle stem cells (MuSCs). However, there is a lack of extensive research on how each of these proteins influences proliferation and differentiation of MuSCs from livestock animals. Therefore, we investigated the effects of various ECM coatings-collagen, fibronectin, gelatin, and laminin-on the proliferation, differentiation, and maturation of porcine MuSCs. Porcine MuSCs, isolated from 14-day-old Berkshire piglets, were cultured on ECM-coated plates, undergoing three days of proliferation followed by three days of differentiation. MuSCs on laminin showed higher proliferation rate than others (p<0.05). There was no significant difference in the mRNA expression levels of PAX7, MYF5, and MYOD among MuSCs on laminin, collagen, and fibronectin (p>0.05). During the differentiation period, MuSCs cultured on laminin exhibited a significantly higher differentiation rate, resulting in thicker myotubes compared to those on other ECMs (p<0.05). Also, MuSCs on laminin showed higher expression of mRNA related with maturated muscle fiber such as MYH1 and MYH4 corresponding to muscle fiber type IIx and muscle fiber type IIb, respectively, compared with MuSCs on other ECM coatings (p<0.05). In summary, our comparison of ECMs revealed that laminin significantly enhances MuSC proliferation and differentiation, outperforming other ECMs. Specifically, muscle fibers cultured on laminin exhibited a more mature phenotype. These findings underscore laminin's potential to advance in vitro muscle research and cultured meat production, highlighting its role in supporting rapid cell proliferation, higher differentiation rates, and the development of mature muscle fibers.

• The Korean Journal of Pesticide Science
• /
• v.4 no.4
• /
• pp.72-76
• /
• 2000

The study was conducted to investigate the developmental periods and effect of several insecticides on Hemiptarsenus sp., ectoparasitoid of Liriomyza trifolii. The mean length and width of egg were 0.5mm and 0.1mm. The mean length of larva, pupae, abult female, and abult male were 1.9mm, 2.0mm, 2.2mm, and 1.8mm, respectively. Developmental periods of Hemiptarsenus sp. from egg to larva at 15, 20, 25, $30^{\circ}C$ were 16.9, 8.8, 5.9, and 4.5 days, and those of pupa were 20.7, 9.7, 5.6, and 3.4 days, respectively. Based on these results, developmental threshold temperatures and effective temperatures were $9.5^{\circ}C$, 91.5 degree-days in egg-larval stage, $10.9^{\circ}C$, 142.3 degree-days in pupal stage. When several insecticides were evaluated to Hemiptarsenus sp. at the recommended concentrations, B.t WP, diflubenzuron WP, and cyromazin were negligiblly effective all life stages. Fipronil SC, cartap SP, spinosad GW were less toxic to larva and pupa, but highly toxic to adults. Abamectin EC was less toxic to all life stages, but inhibited oviposition of 50% more to Hemiptarsenus sp. female.