• 전자공학회논문지SC
• /
• 제40권3호
• /
• pp.199-207
• /
• 2003

종래 직접 퍼지제어기에서는 누적 오차의 발생과 제어입력의 누적으로 인한 과도응답의 성능을 악화시킬 수 있으며 이러한 단점의 보완은 제어입력만으로 결정하기 어렵다. 본 논문에서는 이러한 문제점을 해결하기위해 과도상태에서 나타나는 오버슈트와 상승시간을 고려하기 위해 퍼지제어기를 이용한 재설정 변화분을 설정하며 이를 직접 퍼지제어기에 추가하여 병렬형태로 구성된 새로운 퍼지제어기를 구성한다. 본 논문에서 제시한 새로운 퍼지제어기를 IPMSM 드라이브에 적용하여 새로운 퍼지제어기가 직접 퍼지제어기와 비교하여 응답성능이 우수함을 제시하고 그 타당성을 입증한다.

• 한국강구조학회 논문집
• /
• 제15권5호통권66호
• /
• pp.519-529
• /
• 2003

최근에 스틸하우스나 고층아파트 지붕에 경량형강 지붕트러스의 사용이 증가하는 추세이다. 그러나 현재 지붕트러스와 하부구조의 앵커 접합부의 설계는 거의 경험에 의존하는 실정이다. 본 논문에서는 냉간성형형강 지붕트러스 앵커 접합부의 구조적인 거동에 관한 실험적인 연구를 서술하였다. 트러스부재와 접합철물은 스크류로 접합하였으며, 하부구조의 구조재료에 따라 시공성 및 구조적인 성능이 우수한 단순한 형태의 접합철물을 사용하여 철근콘크리트구조인 경우 케미컬 앵커볼트 그리고 강구조인 경우는 용접 및 DX-Pin을 사용하여 하부구조와 연결하였다. 다양한 접합부 형태에 대한 인발실험을 수향하여 접합부의 강도 및 강성을 측정하였으며, 이를 AISI시방서(1996) AISC시방서(1989)규정에 근거한 설계강도와 비교하였다. 또한 스크류 연결부의 최대전단강도식을 제안하여 실험결과와 비교하였다.

• 한국수자원학회논문집
• /
• 제30권5호
• /
• pp.423-430
• /
• 1997

수자원개발 계획과 설계를 위한 설계홍수량 추정에 가장 중요한 문제의 하나가 유효우량 추정이다. 우리나라 수공구조물의 설계홍수량 추정에는 미국 SCS에서 개발한 유출곡선번호(curve number)로부터 유효우량을 추정하고 홍수도달시간을 고려하여 단위도를 합성하는 방법이 자주 사용되고 있다. 그러나, 우리나라의 경우 시간별 강우-유출량 자료가 충분하지 못한 상태이므로 SCS 유출곡선번호 방법을 그대로 적용하여 유효우량을 추정할 때에는 신중을 기해야 한다. 왜냐하면 우리나라의 토양, 식생 토지이용, 배수조건 등의 유출특성이 미국 유역의 유출특성과 다르고 특히 논이라는 독특한 토이이용형태가 13%나 차지하고 있기 때문이다. 이에 본 연구에서는 유역이 가장 건조한 상태의 유출곡선번호 CN-I을 SCS 유출곡선번호에서 구하지 않고 강우-유출모형인 DAWAST(DAily WAtershed STreamflow, 김태철, 1992) 모형의 유역 최대잠재저류능인 Umax로부터 구하는 방법을 제시하였다. 이매개변수 Umax는 우리나라 유역에서 관측된 일별 강우-유출량 자료를 최적화 기법으로 보정하여 구했으므로 이로부터 추정된 유출곡선번호는 우리나라의 유역특성이 반영되었다고 볼 수 있다.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.58-66
• /
• 2013

Recently, PV module that the most important part of the photovoltaic system is more widened to lower manufacturing costs for module. However, the broad PV module results to the serious mechanical damage corning from installation circumstances such as snow, wind etc of snow and finally lead to the dramatic degradation of the electrical behavior of PV module. In this paper, 3 kinds of PV modules that consist of the different thickness and area of front glass and the diverse cross sectional structures of the frame are prepared for this experiment. The drooped length and electrical outputs of the PV modules are measured by means of applying 600Pa mechanical load to the PV modules from 1200Pa to 5400Pa base on the mechanical load test procedure of K SC IEG 61215 standard. The simulation data are obtained by the simulation tool as ANSYS and those are validate by comparing with the those experimental results figure out relations between the deformation and the constituent part of PV module.

• 대한건축학회논문집:구조계
• /
• 제34권9호
• /
• pp.3-10
• /
• 2018

While computer environments have been dramatically developed in recent years, as the building structures become larger, the structural analysis models are also becoming more complex. So there is still a need to model one shear wall with one finite element. From the viewpoint of the concept of FEA, if one shear wall is modeled by one finite element, the result of analysis is not likely accurate. Shear wall may be modelled with various finite elements. Among them, considering the displacement compatibility condition with the beam element connected to the shear wall, plane stress element with in-plane rotational stiffness is preferred. Therefore, in order to analyze one shear wall with one finite element accurately, it is necessary to evaluate finite elements developed for the shear wall analysis and to develop various plane stress elements with rotational stiffness continuously. According to the above mentioned need, in this study, the theory about a plane stress element using hierarchical interpolation equation is reviewed and stiffness matrix is derived. And then, a computer program using this theory is developed. Developed computer program is used for numerical experiments to evaluate the analysis results using commercial programs such as SAP2000, ETABS, PERFORM-3D and MIDAS. Finally, the deflection equation of a cantilever beam with narrow rectangular section and bent by an end load P is derived according to the elasticity theory, and it is used to for comparison with theoretical solution.

• 대한건축학회논문집:구조계
• /
• 제35권2호
• /
• pp.3-11
• /
• 2019

The recent earthquake of Pohang (M5.4) and the Gyeongju earthquake (M5.8) suggested the possibility of a strong earthquake in Korea and reminded us that the Korea is no longer an earthquake-safe zone. In the disaster recovery stage in a disaster like an earthquake, the investigation of the damage situation and the safety assessment of the building serve to provide important information for the initial action such as establishment of the recovery strategy and rescue of the survivor. However, the research that depends on manpower can not cope with the difficulty of processing a large number of doses in a short time, and the expertise of the manpower must be taken into consideration, which may result in delayed initial action. In this study, we propose an rapid safety evaluation technique of building using unmanned aerial vehicle which evaluates the performance and safety of buildings by integrating conventional safety inspection method with unmanned aerial vehicle technology and developed evaluation method of each evaluation factor. In order to verify this, the buildings damaged by the earthquake in Pohang were checked and compared using this system. The results are consistent with the results of the existing emergency earthquake risk assessment. As a result, the possibility of checking the emergency safety using the unmanned aerial vehicle for the damaged structures in case of a large-scale disaster such as an earthquake was confirmed.

• 대한건축학회논문집:구조계
• /
• 제36권4호
• /
• pp.153-161
• /
• 2020

This study investigates the recycling potential of demolition waste (DW) according to building structure, while considering economic aspects. For that, this study surveyed 1,034 residential buildings to collect reliable information on demolition waste generation rates (DWGRs). This study suggested a method for operational cost calculation for each stage and carried out an inventory analysis. The economic value of recycled DW materials was also calculated. And then, the recycling potential(RP) was calculated by building structures and waste types. RP by building structure was low (27-40%), and RP was found in the order of masonry-block, wooden, RC and concrete-brick. By type of DWs, the RP of aggregates was considerably lower than 7%, and DWs such as wood, plastics, and metals showed more than 100% RP. Considering the results of this study, In order to improve the RP of buildings and DWs, the diversification of products that recycled waste like aggregates (i.e., mortar, concrete, bricks, blocks, tiles) and the development of high value-added products are considered to be the most urgent problems. Based on the above RP results, this study proposed a more advanced method for life cycle assessment of buildings and demolition waste.

• 대한건축학회논문집:구조계
• /
• 제35권12호
• /
• pp.137-148
• /
• 2019

Korean piloti-type buildings are comprised of pilotis in the first story and shear walls in the upper stories. This vertical irregularity causes excessive lateral plastic deformation on the first story while the upper stories stay elastic. Meanwhile, asymmetric position of structural components such as core walls and columns of RC piloti-type buildings tends to produce torsional irregularities of the structures. Korean Building Code(KBC2016) requires the special seismic load and torsional amplification factor to apply to the piloti-type buildings lower than six-story or 20m if it has vertical and torsional irregularities when the building corresponds to seismic design category C or D. Many Korean low-rised RC buildings fall into the class. Therefore, the special earthquake load and torsional amplification factor are often applied to a building simultaneously. However, it has not been studied enough how much influence each parameter has on buildings with vertical and torsional irregularities at the same time. The purpose of this study is to evaluate the effect of factor special seismic load and torsional amplification on seismic performance of irregular buildings. In this study, a damaged 4^th story piloti-type building by the Pohang earthquake was selected and the earthquake response analysis was carried out with various seismic design methods by the KBC 2016. The effect of the design parameters on seismic performance was analyzed by the dynamic analysis of models with special seismic load and torsional amplification factor based on the selected building. It was concluded that the application of the torsional amplification factor to the reference model to which special seismic design was applied, does not significantly affect the seismic performance.

• 대한건축학회논문집:구조계
• /
• 제33권12호
• /
• pp.37-44
• /
• 2017

Due to structural characteristics, construction costs and duration of a modular system would be saved by minimizing the schedule on the job site. As such, it is crucial to develop a connection that can guarantee stiffness while allowing for simple assembling. Particularly, the mid- to high-rise construction of the modular system necessitates the securing of the structural stability and seismic performance of multi-unit frames and connections, and thus, the stiffness of unit-assembled structures needs to be re-evaluated and designed. However, evaluating a frame consisting of slender members and reinforcing materials is a complicated process. Therefore, the present study aims to examine the structural characteristics of a modular unit connection based a method for reinforcing connection brackets and hinges while minimizing the loss of the cross section. Toward this end, the study modeled the beam-to-column connection of a modular system with the proposed connection, and produced a specimen which was used to perform a cycling loading test. The study compared the initial stiffness, the attributes of the hysteretic behavior, and the maximum flexural moment, and observed whether the model acquired the seismic performance, compared to the flexural strength of the steel moment frame connection that is required by the Korean Building Code. The test results showed that the proposed connection produced a similar initial stiffness value to that of the theoretical equation, and its maximum strength exceeded the theoretical strength. Furthermore, the model with a larger ceiling bracket showed higher seismic performance, which was further increased by the reinforcement of the plate.

• 대한건축학회논문집:구조계
• /
• 제34권2호
• /
• pp.29-40
• /
• 2018

Strength design wind loads for the wind resistance design of structures shall be evaluated by the product of wind loads calculated based on the basic wind speed with 100 years return period and the wind load factor 1.3 specified in the provisions of load combinations in Korean Building Code (KBC) 2016. It may be sure that the wind load factor 1.3 in KBC(2016) had not been determined by probabilistic method or empirical method using meteorological wind speed data in Korea. In this paper, wind load factors were evaluated by probabilistic method and empirical method. The annual maximum 10 minutes mean wind speed data at 69 meteorological stations during past 40 years from 1973 to 2012 were selected for this evaluation. From the comparison of the results of those two method, it can be found that the mean values of wind load factors calculated both probability based method and empirical based method were similar at all meteorological stations. When target level of reliability index is set up 2.5, the mean value of wind load factors for all regions should be presented about 1.35. When target level of reliability index is set up 3.0, wind load factor should be presented about 1.46. By using the relationship between importance factor(conversion factor for return period) and wind load factor, the return periods for strength design were estimated and expected wind speeds of all regions accounting for strength design were proposed. It can be found that return period to estimate wind loads for strength design should be 500 years and 800 years in according to target level of reliability index 2.5 and 3.0, respectively. The 500 years basic wind speed map for strength design was suggested and it can be used with a wind load factor 1.0.