• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.793-804
• /
• 1994

Turbulence intensity caused by piston movement was almost as same tendency as the piston speed. The turbulence intensity was increased from 0.39m/s to 0.79m/s when mean piston speed increased from 2.33m/s to 4.67m/s. In this case the maximum turbulence intensity caused by piston speed was decreased about 82 percent near the top dead center at the end of compression stroke. The maximum turbulence intensity was created from 12m/s to 22m/s when inlet flow velocity was increased from 22m/s to 45m/s. Also turbulence intensity caused by inlet flow velocity was linearly increased from 0.97m/s at top dead center at the end of compression stroke. The ratio of turbulence intensity and mean inlet flow velocity was about 3 percent for inlet flow velocity.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.390-395
• /
• 2004

The characteristics of the circular arc shaped multi-blade windmil are investigatedl. The prototypical windmill was tested in the laboratory at wind tunnel speeds of 5.5, 9.4m/s. and the model windmill was also tested in the laboratory, The power and torque coefficients were studied as functions of the blade section, the aspect ratio for blade diameter and windmill radius(M = 0.3, 0.5, 0.7), the number of blades and finally the tip-speed ratio. The analysis of the experimental results for the model windmill showed that there is the highest revolutions per minute(R.P.M) at the circular arc shaped multi-blade windmill having the blade number 10, aspect ratio(M = 0.7). and the results for the prototypical windmill showed that the power coefficient increased to a maximum value and then decreased again with an increase in the tip speed ratio, while the torque coefficient decreased directly with an increase in the tip speed ratio Finally, the experimental results were compared with the Savonius blade. the maximum power coefficient for the arc shaped blade was greater than for the Savonius blade and occured at a lower tip speed ratio.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.5
• /
• pp.191-202
• /
• 2019

This study examines the effect of luminance contrast ratio of character on readability and visual fatigue during an hour-long reading session while using a tablet PC in ambient environments having low luminance limited to $25cd/m^2$. Experiments were conducted with four patterns of the tablet's luminance contrast ratio of characters, namely 1:2.5, 1:4.5, 1:6.5, and 1:8.5, in low ambient luminance of $9cd/m^2$ and $25cd/m^2$. The obtained results show that the characters can be easily read at the luminance contrast ratio of character of 1:8.5 under surface luminance of $25cd/m^2$. Visual fatigue was evaluated through a subjective survey of symptoms. Physical, psychological, and visual fatigue were observed at a surface luminance of $9cd/m^2$, whereas solely visual fatigue was felt at a surface luminance of $25cd/m^2$. By assessing the physical fatigue using the value, it has been found that smaller the luminance contrast ratio of character, greater is the CFF variation rate. Furthermore, readability is poor and visual fatigue can be observed when the surface luminance is lower than the ambient luminance. However, readability can be improved by increasing the luminance contrast ratio of character to a value of 1:8.5. Thus, in low luminance environments, luminance contrast ratio of characters can affect readability and fatigue. Consider providing the full form of "CFF" so that the acronym can be used unambiguously throughout the manuscript.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1277-1280
• /
• 2005

A high-aspect-ratio and high-resolution stainless steel shadow mask for organic thin-film transistors (OTFTs) circuit has been fabricated by a new method which combines photochemical machining, micro-electrical discharge machining (micro-EDM), and electrochemical etching (ECE). First, connection lines and source-drain holes are roughly machined by photochemical etching, and then the part of source and drain holes is finished by the combination of micro-EDM and ECE processes. Using this method a $100\;\mu{m}$ thick stainless steel (AISI 304) shadow mask for inverter can be fabricated with the channel length of $30\;\mu{m}\;and\;10\;\mu{m}\;respectively.\;The\;width\;of\;connection line\;is\;150\;\mu{m}$. The aspect ratio of the wall is about 5 and 15, respectively. Metal lines and source-drain electrodes of OTFTs were successfully deposited through the fabricated shadow mask.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.253-259
• /
• 2002

Micro cell structures with high aspect ratio were fabricated by injection molding method. The mold inserts had dimension $1.9cm\times8.3cm$ composed of a lot of micro posts and were fabricated by LIGA process. The size of the micro posts was $157{\mu}m\times157{\mu}m\times500{\mu}m$ and the gaps between two adjacent posts were $50{\mu}m$. Using Polymethylmethacrylate (PMMA) injection molding was performed. The key experimental variables were temperature, pressure, and time. By controlling these, good shaped mim cell structures with $50{\mu}m$ in wall thickness and $500{\mu}m$ in depth were obtained. In order to understand micro molding mechanism, shape changes of molded PMMA were studied with experimental variables. And the durability of mold insert was investigated, too. The results show that the most important factor in molding processes was the mold temperature that is closely related to the filling of the melt into the micro cavity. And the holding time before cooling showed a great effect on the quality of molded PMMA.

• Ocean and Polar Research
• /
• v.45 no.4
• /
• pp.201-209
• /
• 2023

Melosira nummuloides (KNU-HAPCC-101), which is a biological resource for fucoxanthin extraction, was separated from single cells, and optimal growth conditions were derived according to temperature, salinity, light intensity, light emitting diode, N:P ratio of culture medium, and dilution ratio of culture medium. These parameters were assessed to ascertain the best culture conditions for the most economical and efficient indoor mass production. The specific growth rate was the highest at 25℃ in temperature, but there was no significant difference between 15℃ and 20℃. M. nummuloides died at 0 psu in salinity, and the specific growth rate was the highest at 30 psu in respect to salinity. The light intensity was similar in all experimental groups except for 5 µmol photons m^-2 s^-2. The maximum biomass and specific growth rate in the light-emitting diode experiment were revealed at the red wavelength, but the concentration of chlorophyll-a was the lowest at the red wavelength whereas the white wavelength produced the highest chlorophyll-a concentration. In the experiment according to the ratio of nitrogen and phosphorus (N:P) based on the f/2 culture medium, the growth rate was significantly higher in the 15:1 to 50:1 ratio range. The growth rate according to the dilution concentration of the f/2 culture medium was the highest in the f/2 culture medium, but did not show a significant difference from the f/4 culture medium. M. nummuloides can be mass-cultured under conditions of a temperature of 15-25℃, a salinity of 15-35 psu, light intensity of 25-150 µmol photons m^-2 s^-2, and f/4 media concentration level with an N:P ratio 15:1 or more. Based on the data of this study, it is expected that fucoxanthin can be produced in a highly efficient manner through the development of a mass culture system.

• Journal of Environmental Science International
• /
• v.7 no.5
• /
• pp.679-685
• /
• 1998

The Soysauce wastewater removal characteristics of submerged biofilters filled with two filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. The decreasing order of BOD removal is Netring(random plastic media), cubic wire meshes(plastic module). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. The BOD removal ratio decreases with increasing $BOD_5$/ volumetric loading rate, and the loading rate for the BOD removal over 85% is lower than 1.5kg$BOD_5$ 5/$m^3$d for the plastic media of Netring and cubic wire meshes. The $BOD_5$ removal rate increases with the recirculation ratio, but the rate of increase become smaller as the recirculation ratio increases over 20. When $BOD_5$ volumetric loading is 1.5kg$BOD_5$/$m^3$d, the required recirculation ratio to obtain 85% BOD$_{5}$ removal is about 20 for Netring and it was about 30 for cubic wire meshes.s.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.3
• /
• pp.37-42
• /
• 2003

Physical properties of paper can be explained in terms of the changes in fiber's morphological properties. As the paper machine speed increases, the basis weight decreases and the mixing ratio of inferior recycled fibers increases, paper break becomes important than ever before. One of the objectives of this study is to analyze paper's physical, mechanical and fracture mechanical properties depending on softwood(SW) and hardwood(HW) mixing ratios and recycling. Fibers were refined by Valley beater to 450 mL CSF. Handsheets of 30 g/$\textrm{m}^2$ were prepared at different mixing ratios. Fracture toughness was measured as the amount of energy applied to cracked sample before total failure. Fracture toughness showed different trend to other strength properties. At the mixing ratio of SW 80: HW 20, papers showed the maximum fracture toughness. At this mixing ratio, flexible softwood fibers were mostly broken and stiff hardwood fibers were mostly pulled out.

• Steel and Composite Structures
• /
• v.42 no.3
• /
• pp.353-361
• /
• 2022

In this study, an estimation regarding nonlocal shell model based on wave propagation approach has been considered for vibrational behavior of the double walled carbon nanotubes with distinct nonlocal parameters. Vibrations of double walled carbon nanotubes for chiral indices (8, 3) have been analyzed. The significance of small scale is being perceived by developing nonlocal Love shell model. The influence of changing mechanical parameter Poisson's ratio has been investigated in detail. The dominance of boundary conditions via nonlocal parameter is shown graphically. It is found that on increasing the Poisson's ratio, the frequencies increases. It is noted that the frequencies of clamped-clamped frequencies are higher than that of simply-supported and clamped-free edge conditions. The outcomes of frequencies are tested with earlier computations.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.2
• /
• pp.156-164
• /
• 2005

The size of the ship's turning circle is influenced by various factors, such as block coefficient, underwater side shape, rudder area ratio, draft, trim and Froude's number. Most of them are already fixed on departure from a port. However, the ship's speed and the rudder angle are controllable factors which operations are able to change optionally during sailing. The DGPS measured the turning circles according to the ship's speed and the rudder angle. The maximum advances by slow and full ahead were 302m and 311m, and the maximum transfers were 460m and 452m, respectively. There occurs almost no difference in size of the turning circle by variation of the ship's speeds. When the rudder angles were changed to $10^{\circ}$, $20^{\circ}$ and $30^{\circ}$, the maximum advances were 447m, 271m and 202m, and then also the maximum transfers 657m, 426m and 285m, respectively. The diameter of the tuning circle was decreased exponentially when the rudder angle was increased. The maneuverability was better when the direction of turning and propulsion of propeller are in the opposite direction rather than in the same one togetherm. The distance of the maximum transfer was always bigger than that of the maximum advance.