• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.10
• /
• pp.1158-1162
• /
• 2009

Fatigue limit of the copper film coated by Sn was estimated using Goodman diagram and Gerber diagram. To obtain the high cycle fatigue life curve, S-N curve, of the film, the high cycle fatigue test was carried out by applying the constant amplitude load to the film specimen with three different stress ratio of 0.05, 0.3 and 0.5 and the frequency of 40 Hz at room temperature in air. The free-standing film specimen 15.26${\mu}m$ thick was fabricated by etching process. The fatigue limits and S-N curves at the respective stress ratios were determined from the experimental works. It was shown that the S-N curves were dependent on the stress ratio and the fatigue limit was increased with decreasing the stress ratio. The dependency of the fatigue behavior was presented in empirical relationship. Using these relationships, the fatigue limit was predicted.

• Clean Technology
• /
• v.3 no.1
• /
• pp.96-105
• /
• 1997

The objectives of this study were to investigate $SO_2$ removal efficiency of anthracite - bituminous coal blend combustion in a fludized bed coal combustor with Ca/S, anthracite ratio, bed temperature, and waste paper sludge particle size. The experimental results were presented as follow ; the effect of the desulfurization by the particle size of waste paper sludge was a great and $SO_2$ removal efficiency was heigest in paper sludge dia $1016{\mu}m$. And the difference of $SO_2$ removal efficiency according to air velocity was not too large. As Ca/S mole ratio incresed, $SO_2$ removal efficiency incresed rapidly up to Ca/S mole ratio 3 while the desulfurization rates did not increse too largely in the range of more than the level. The bed temperature had a great deal of effect on the desulfurization rate. So the $SO_2$ removal efficiency was a graet using waste paper sludge that the properbility of paper sludge as sorbent was conformed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.4
• /
• pp.679-686
• /
• 1997

In order to investigate the distribution characteristics of polychlorinated Biphenyls (PCBs) at the southern of Korean East Sea, vertical measurements of temperature, salinity, DO and PCBs were performed by each depth of 5 stations during August - October 1996. Thermocline and salinocline were generally existed at depth of 30 m and water mass current of midwater in the southern of Korean East Sea was distributed below 30 m depth. The distribution of surface water mass in this area was extended to Tsusima area from the southern offshore of the Korean last Sea. In August 1996, concentration range of PCBs had $0.22\~0.36\;ng/\ell$ at surface layer and their concentrations at near Tsusima offshore were relatively decreased. Total mean concentration of PCBs was $0.29\;ng/\ell$ in the sea surface and $0.31\;ng/\ell$ in the middle layer. PCBs seemed to correlate well with suspended particles. And vortical and horizontal distribution of their concentrations showed comparatively uniform pattern. Relatively high compositional ratio of Di- and Tri-PCBs could be found at the sea surface, while compositional ratio of Penta-PCBs dominates over other congener at deep layer.

• Journal of the Korean Chemical Society
• /
• v.27 no.1
• /
• pp.18-23
• /
• 1983

To understand the abnormal absorption behavior of rare earths in cation exchange resins, the absorption for Ce(III), Tb(III) and $Cl^-$ ions in Dowex 50W-X2 have been investigated by spectrophotometry in the concentration range of $1{\sim}12$ M HCI and $HCl-HClO_4$ mixed solutions. The amount of $Cl^-$ ion absorbed shows that the ratio of amount of $Cl^-$ ions to that of rare earths does not exceed 10% in the concentration range of $6{\sim}8M$ HCl and decreased gradually to 3% at 2M HCl and 6% at 12M HCl. The ratio is further decreased with the fraction of $HClO_4$ in $HCl-HClO_4$ mixed solutions and the decrease is presumably due to the weak tendency to form a complex between rare earths and $Cl^-$ ions in a cation exchange resin. The effect of $ClO_4^-$ is expected to play a more important role than that of $Cl^-$ ions in the large absorption of rare earths.

• Journal of Biosystems Engineering
• /
• v.30 no.4 s.111
• /
• pp.220-228
• /
• 2005

This study was conducted to investigate the main factors that contain a rotating velocity ratio between wheel and conveyor belt, a tilt angle of conveyor belt and a rotating velocity of a dick cutter for mechanization of Chinese leek harvest. In the survey on the cultivation of Chinese leek, row spacing of 350 m and cutting height of 10 mm from the ground were set up for field tests. Test equipment was designed to cut, pick up and convey Chinese leek one row by one row. From the results of material tests, pick-up height of conveyor belt was set up at $60\~90m$ from the bottom, and the strain and stress at rupture of Chinese leek was 0.487 m/m and 0.01078 MPa. An elastic coefficient of the rubber (Neoprene) of conveyor belts was 1.1077 under the strain of 0.3 nym. from the results of field tests, the tilt angle of conveyor belt was the range of $25^{\circ}\~30^{\circ}$ under consideration far space of container, the velocity ratio between vehicle and conveying belt was 1 to 2.4~1.7 at 0.1~0.3 m/s of vehicle, and optimum rotating velocity of the disk cutter was 34.8 m/s or more under consideration for soil friction.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.3
• /
• pp.247-256
• /
• 2012

Stable carbon isotope ratio of oil components are known to be unaffected by weathering processes and thus has been widely used to determine the origin of spilled oil. In this study, molecular index and composition of stable carbon isotope in 15 crude oils and petroleum product were analyzed and used as oil fingerprints to determine the discriminating power of each fingerprinting method among target crude oils. Through the fingerprints of alkane distribution only Bintulu and B-C(1%) were distinguishable from other crude oils. The pristane/phytane ratio can classify the crude oils into three groups but differentiation of crude oils within a group was impossible using the ratio. The crude oils of A.L., A.S.L., Foroozan and B-C(1%) were differentiated from the other oils using PAH source recognition indexes of C2D/C2P and C3D/C3P. The usage of 4-mD/1-mD and 2/3-mD/1-mD ratio was able to distinguish A.S.L., Bintulu and Oman from the other crude oils. However the PAH source recognition ratios in the other crude oils were similar and thus they were impractical to be used for source identification among the target crude oils. Stable carbon isotope ratios of alkanes were able to uniquely specify each crude oil in the plot of ${\delta}^{13}C_{C21}$ and ${\delta}^{13}C_{C25}$ except A.L., A.M., Qatar-Marine, B-C(1%). The oil fingerprinting method using stable carbon isotope ratios of individual alkane compounds showed more discriminating power among the target crude oils than the conventional source recognition indexes of PAHs or alkanes.

• Journal of Power System Engineering
• /
• v.13 no.3
• /
• pp.47-52
• /
• 2009

The effect of forging start temperature, forging ratio on the microstructure and mechanical properties of B7B4 steel ware investigated. Microstructure of centrifugal casted B7B4 steel consisted of martensite and ferrite phase. The volume fraction of ferrite increased with increase of forging start temperature and decreased with increase of forging ratio. Tensile strength and hardness decreased with higher of forging start temperature, while impact value and elongation increased with higher of forging start temperature. With increase of forging ratio, tensile strength rapidly increased up to the forging ratio of 30%, and then slowly increased, but elongation was decreased. Hardness and impact value rapidly increased with increase of forging ratio.

• Macromolecular Research
• /
• v.17 no.10
• /
• pp.797-806
• /
• 2009

The mechanical and thermal behaviors of polyamide-6/clay nanocomposites were studied using the continuum-based, micromechanical models such as Mori-Tanaka, Halpin-Tsai and shear lag. Mechanic-based model prediction provides a better understanding regarding the dependence of the nanocomposites' reinforcement efficiency on conventional filler structural parameters such as filler aspect ratio ($\alpha$), filler orientation (S), filler weight fraction (${\Psi}_f$), and filler/matrix stiffness ratio ($E_f/E_m$). For an intercalated and exfoliated nanocomposite, an effective, filler-based, micromechanical model that includes effective filler structural parameters, the number of platelets per stack (n) and the silicate inter-layer spacing ($d_{001}$), is proposed to describe the mesoscopic intercalated filler and the nanoscopic exfoliated filler. The proposed model nicely captures the experimental modulus behaviors for both intercalated and exfoliated nanocomposites. In addition, the model prediction of the heat distortion temperature is examined for nanocomposites with different filler aspect ratio. The predicted heat distortion temperature appears to be reasonable compared to the heat distortion temperature obtained by experimental tests. Based on both the experimental results and model prediction, the reinforcement efficiency and heat resistance of the polyamide-6/clay nanocomposites definitely depend on both conventional (${\alpha},\;S,\;{\Psi}_f,\;E_f/E_m$) and effective (n, $d_{001}$) filler structural parameters.

• Fibers and Polymers
• /
• v.7 no.3
• /
• pp.295-304
• /
• 2006

High-bulk worsted yams with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yams and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and $2000 g/cm^2$) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40 % shrinkable fibre blending ratio the maximum yam bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20 % shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V') which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knit-miss structures. In addition, at 20 % shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.

• Environmental Engineering Research
• /
• v.17 no.2
• /
• pp.89-94
• /
• 2012

Pyrolysis/gasification technology utilizes an energy conversion technique from various waste resources, such as biomass, solid waste, sewage sludge, and etc. to generating a syngas (synthesis gas). However, one of the major problems for the pyrolysis gasification is the presence of tar in the product gas. The tar produced might cause damages and operating problems on the facility. In this study, a gliding arc plasma reformer was developed to solve the previously acknowledged issues. An experiment was conducted using surrogate benzene and naphthalene, which are generated during the pyrolysis and/or gasification, as the representative tar substance. To identify the characteristics of the influential parameters of tar decomposition, tests were performed on the steam feed amount (steam/carbon ratio), input discharge power (specific energy input, SEI), total feed gas amount and the input tar concentration. In benzene, the optimal operating conditions of the gliding arc plasma 2 in steam to carbon (S/C) ratio, 0.98 $kWh/m^3$ in SEI, 14 L/min in total gas feed rate and 3.6% in benzene concentration. In naphthalene, 2.5 in S/C ratio, 1 $kWh/m^3$ in SEI, 18.4 L/min in total gas feed rate and 1% in naphthalene concentration. The benzene decomposition efficiency was 95%, and the energy efficiency was 120 g/kWh. The naphthalene decomposition efficiency was 79%, and the energy yield was 68 g/kWh.