• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.376-382
• /
• 2006

In this work, pitch/activated carbon/$TiO_2$ composite were prepared by $CCl_4$ solvent method with different mixing ratios. The BET surface area of pitch/activated carbon/$TiO_2$ composite has a significantly increase with increasing activated carbon content in pitch/activated carbon/$TiO_2$ composite. The surface structure and elemental compositions of the composite were studied by SEM and EDX, respectively. The SEM results were presented to the characterization of porous texture on the pitch/activated carbon/$TiO_2$ composite. And EDX data was shown the presence of C, O, S, Ti and other elements. The structural properties of the composite were studied in XRD measurements. The $TiO_2$ crystal phases of the pitch/activated carbon/$TiO_2$ composite had lots of rutile-type structure which transforms from anatase-type with a little of anatase-type structure. The photocatalytic activities of the composite were evaluated using a photo-decomposition method under UV lamp. The pitch/activated carbon/$TiO_2$ composites were observed better photocatalytic activity than that of pristine $TiO_2$.

• Journal of the Korean Magnetics Society
• /
• v.16 no.4
• /
• pp.206-210
• /
• 2006

A room-temperature ferromagnetism has been observed for oxygen-deficient rutile and anatase $TiO_{2-{\delta}}$ films. XPS data revealed the existence of $Ti^{3+}$ ions, for compensating the charge imbalance caused by oxygen vacancies in the film. The observed ferromagnetism is attributable to the spin ($3d^1$) alignment of the $Ti^{3+}$ ions. Such spin alignment can happen through magnetic polaron formed by trapped electron in oxygen vacancy and magnetic $Ti^{3+}$ ions around it.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.187-193
• /
• 2005

The photocatalyst $TiO_2$ thin film was made from titanium (IV) isopropoxide, ethanol, and HCl by sol-gel method. The surface observation by SEM showed the sample that was coated 5 times at $500^{\circ}C$ had good properties. The component ratio, in atom% of O : Ti by EDX analysis, of 61 : 39 by spin coating was superior than dip coating. It was found that crystal structure changed from anatase phase to rutile phase as a function of the temperature of thin film fabrication, and this was measured by XRD. The photolysis efficiency of total organic compounds (TOC) by lighting UV beam on $TiO_2$ thin film showed 20%~65% within 1 h, and decreased slowly thereafter.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.427-431
• /
• 2012

The $TiO_2$ foam synthesized using freeze-casting is a promising photocatalyst and photovoltaic electrode for a variety of energy applications, because the freeze-casting technique is easy to use, cheap, and suitable for mass-production. Despite its several advantages, little scientific information is available on the processing and morphology of the $TiO_2$ foams processed by freeze-casting. In particular, no systematic study has been performed on the microstructural evolution and morphological change of the rutile-phase $TiO_2$ foams during sintering. Therefore, in the present study, several $TiO_2$ foam samples were produced using the freeze-casting technique, which were then sintered at a relatively high temperature of $1200^{\circ}C$ for 1, 2, and 4 h to compare the morphological changes in the microstructure and to understand the effects of processing parameters of the rutile-phase $TiO_2$ foams. The foam ligament size increased near linearly with increasing sintering time whereas the average pore size decreased only slightly with increasing sintering time, with changes in particle morphology from sphere to rod and complete phase transformation from anatase to rutile.

• Korean Journal of Optics and Photonics
• /
• v.16 no.2
• /
• pp.168-173
• /
• 2005

Ag-doped $TiO_2$ thin films were prepared by RF magnetron co-sputtering method, and their physical and chemical properties were examined as a function of calcination temperature. XRD results showed that the crystallite size of Ag-doped films was smaller than that of the $TiO_2$ thin films. SEM results showed that the particle size of $Ag/TiO_2$ film was smaller and more uniform than pure $TiO_2$ film. The films had high transparency in the visible range. The films calcined at $600^{\circ}C$ were the anatase phase, and the films calcined at $900^{\circ}C$ were a mixture of anatase and rutile phases. The absorption edge of films calcined at $900^{\circ}C$ was red-shifted. This is due to the augmented absorption resulting from the phase transformation from anatase to rutile phase. And the transmittance of films decreased by the light scattering and absorption in the films. Photocatalytic activity of $Ag/TiO_2$ thin films was higher than that of the pure $TiO_2$ thin films.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.947-954
• /
• 2002

HCl concentration and reaction time are the decisive factors in determining the structure of precipitates in the process of synthesis of $TiO_2$ particles from aqueous $TiOCl_2$ solution by precipitation and the volumetric proportion of brookite phase in $TiO_2$ particles can be controlled by these two factors. As reaction rate increases with increase of reaction temperature, the reaction time, at which maximum volumetric proportion of brookite phase in $TiO_2$ particles was obtained, was reduced. The brookite was transformed directly to rutile phase with only increase of reaction time. And precipitation was delayed with increase of HCl concentration because the amount of $H_2$O, which is necessary source of oxygen for conversion of $Ti^{+4}$ to $TiO_2$, was relatively reduced with increase of that. Brookite in the mixture phase powder was finally transformed to rutile phase via anatase through heat-treatment.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.543-546
• /
• 2015

$TiO_2$ nanowires were grown by thermal oxidation of TiO powder in an oxygen and nitrogen gas environment at $1000^{\circ}C$. The ratio of $O_2$ to $N_2$ in an ambient gas was changed to investigate the effect of the gas ratio on the growth of $TiO_2$nanowires. The oxidation process was carried out at different $O_2$/$N_2$ ratios of 0/100, 25/75, 50/50 and 100/0. No nanowires were formed at $O_2$/$N_2$ ratios of less than 25/75. When the $O_2$/$N_2$ ratio was 50/50, nanowires started to form. As the gas ratio increased to 100/0, the diameter and length of the nanowires increased. The X-ray diffraction pattern showed that the nanowires were $TiO_2$ with a rutile crystallographic structure. In the XRD pattern, no peaks from the anatase and brookite structures of $TiO_2$were observed. The diameter of the nanowires decreased along the growth direction, and no catalytic particles were detected at the tips of the nanowires which suggests that the nanowires were grown with a vapor-solid growth mechanism.

• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.721-729
• /
• 1991

SnO2-TiO2(Pt or Pd), as raw material for hydrocarbon gas sensors, was prepared by a coprecipitation method. The SnO2-TiO2-based thick film gas sensors were made by screen printing technique. The titanium dioxide synthesized was shown to be anatase structure from XRD peaks and was transformed to rutile structure between 700$^{\circ}C$ and 1000$^{\circ}C$. Titanium dioxide in SnO2-TiO2 thick films devices plays a very important role in the enhancement of the sensitivity to CH4 and C4H10. In the case of SnO2-TiO2(Pt) sensors, titanium dioxide that was rutile structure enhanced the sensitivity of the thick film to CH4. Platinum added to the raw powder at coprecipitation (as chloroplatinic acid VI hydrate) improved the gas sensitivity to hydrocarbon gases. Therefore, it is expected that the SnO2-TiO2(Pt) thick film sensors fabricated in this experiment could be put into practical use as LPG (primary component : C4H10 and C3H8) and LNG (primary component : CH4) sensors.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2006.02a
• /
• pp.192-192
• /
• 2006

• Textile Coloration and Finishing
• /
• v.26 no.2
• /
• pp.88-98
• /
• 2014

This study is to assess the photocatalytic degradation of PET and Nylon 6 films containing nano-sized $TiO_2$ powders of anatase and rutile types. The PET and Nylon 6 films containing six kinds of the nanoparticles were prepared by melt casting method using a heating press machine. Reflectance in visible region and water contact angles of the irradiated PET and Nylon 6 composite films decreased with increasing UV/$O_3$ irradiation. Also the enhanced hydrophilicity has a close relationship with the increase in the Lewis base parameter, which indicates more oxidized polymer surfaces. The photocatalytic degradation of the nanocomposite films increased with increasing $TiO_2$ content and UV energy, which is more significant with the anatase types rather than the rutile types. The amide linkages in the Nylon 6 seemed to be more susceptible to the UV light compared to the ester groups in the PET, particularly in the presence of the $TiO_2$ photocatalysts. The photoscission and photodegradation of the polymers in the composites produced more degraded structure assisted by the photocatalytic activity of the $TiO_2$ nanoparticles. Also the composite films can bleach the methylene blue dyes more easily under the UV/$O_3$ irradiation, suggesting the photobleaching activity of the $TiO_2$ nanoparticles.