• 한국해양공학회지
• /
• 제21권4호
• /
• pp.28-33
• /
• 2007

The objective of this paper is to investigate the relationship between the short-term creep rupture time and the creep rupture properties at three different elevated temperatures in STS304 stainless steel. Uniaxial constant stress creep rupture tests were performed on the steel to observe the creep rupture behaviors at the elevated temperatures of 600, 650 and 700, according to the testing matrix. It is very important to predict creep life in practical creep design problems. As one of the series of studies on the statistical modelling of probabilistic creep rupture time and the development of creep life prediction techniques, the relationship between applied stress and creep rupture behaviors, such as creep strain rate and rupture time, were investigated. In addition, the Monkman-Grant relationship was observed between the steady-state creep rate and the creep rupture time. The creep rupture surfaces observed by SEM showed up dimple phenomenon at all conditions.

• 대한기계학회논문집
• /
• 제19권5호
• /
• pp.1182-1189
• /
• 1995

Several methods have been developed to predict the creep rupture time of the steam pipes in thermal power plant. However, existing creep life prediction methods give very conservative value at operating stress of power plant and creep rupture strain cannot be well estimated. Therefore, in this study, creep rupture time and strain prediction method accounting for material damage and grain boundary sliding is newly proposed and compared with the existing experimental data. The creep damage evolves by continuous cavity nucleation and constrained cavity growth. The results showed good correlation between the theoretically predicted creep rupture time and the experimental data. And creep rupture strain may be well estimated by using the proposed method.

• 한국해양공학회지
• /
• 제24권6호
• /
• pp.97-102
• /
• 2010

This paper deals with the variability of short term creep rupture time based on previous creep rupture tests and the statistical methodology of the creep life prediction. The results of creep tests performed using constant uniaxial stresses at 600, 650, and $700^{\circ}C$ elevated temperatures were used for a statistical analysis of the inter-specimen variability of the short term creep rupture time. Even under carefully controlled identical testing conditions, the observed short-term creep rupture time showed obvious inter-specimen variability. The statistical aspect of the short term creep rupture time was analyzed using a Weibull statistical analysis. The effect of creep stress on the variability of the creep rupture time was decreased with an increase in the stress level. The effect of the temperature on the variability also decreased with increasing temperature. A long term creep life prediction method that considers this statistical variability is presented. The presented method is in good agreement with the Lason-Miller Parameter (LMP) life prediction method.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.56-62
• /
• 2010

This paper is concerned with the stochastic nature of elevated temperature tensile strength and creep rupture time in 18Cr-8Ni stainless steels. The Weibull statistical analysis using the NRIM data sheet has been performed to investigate the effects of variability of the elevated temperature tensile strength and creep rupture time on the testing temperature. From those investigations, the distributions of temperature tensile strength and creep rupture time were well followed in 2-parameter Weibull. The shape parameter and scale parameter for the Weibull distribution of tensile strength were decreased with increasing the testing temperature. For the creep rupture time, generally, the shape parameter were decreased with increasing the testing temperature.

• 대한기계학회논문집A
• /
• 제24권11호
• /
• pp.2812-2822
• /
• 2000

Several methods have been developed to predict the rupture time of the boiler tubes in thermal power plant. However, existing life prediction methods give very conservative value at operating stress of power plant and rupture strain cannot be well estimated. Therefore, in this study, rupture time and strain prediction method accounting for creep, corrosion and heat transfer is newly proposed and compared with the current research results. The creep damage evolves by continuous cavity nucleation and constrained cavity growth. The corrosion damage evolves by steam side and fire side corrosion. The results showed good correlation between the theoretically predicted rupture time and the current research results. And rupture strain may be well estimated by using the proposed method.

• 한국식품과학회지
• /
• 제29권2호
• /
• pp.273-278
• /
• 1997

몇가지 채소류(오이, 무우, 마늘, 생강 및 감자)의 펀치특성을 살펴보기 위하여 식품물성 측정기로 일정하게 힘을 가하면서 힘-거리-시간 간의 관계를 살펴보고 성분함량 및 세포특성과의 관계를 살펴본 결과는 다음과 같다. 힘-거리 및 거리-시간 곡선 상에는 많은 변곡점 및 파괴점이 관찰되었으며, 이는 시료의 구성세포가 가해진 힘에 대해 저항 또는 항복할때 나타나는 현상으로 탐침속도가 느릴때 크고 분명하였다. 파괴점까지 힘-시간 및 거리-시간에 대한 회귀분석 결과 상관계수는 0.95이상이었다. 탐침이 시료를 관통하는 시간과 그때의 힘은 생강이 5.63초 및 4.88 N으로 컸고 오이가 4.15초 및 2.00 N으로 작았으며, 탐침속도가 빠를 수록 더 많은 파괴힘을 필요로 하였다. 상관관계 분석결과 세포가 클수록 수분함량이 많고 파괴거리가 커지며, 세포의 규칙성, 시료의 즙액, 조밀도와 힘-시간 간의 기울기는 작아지는 관계를 보였다. 비중이 클수록 파괴힘, 거리 및 시간은 작아졌으며, 거리-시간곡선의 기울기는 힘-시간곡선의 기울기와 반비례 관계가 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 추계학술대회 논문집
• /
• pp.74-79
• /
• 1994

The log-log presentation of stress versus Larson-Miller parameter is obtained by uniaxial tensile test instead of the long time creep test. The used material for example calculations is SUS304 stainless steel. The temperature of the uniaxial tensile test can be determined by the Larson-Miller parameter of the design stress and the 0.1hr's rupture time of the uniaxial tensile test. The rupture time at the design temperature and stress can be determined by the Larson-Miller parameter of the stress. The average creep rate is the total deformation of the tensile test divided by the rupture time at the design stress and temperature. The liner trend and the order of the data of the average creep rate by this method is almost same as that of experimental results.

• 한국해양공학회지
• /
• 제22권6호
• /
• pp.58-63
• /
• 2008

The short-term high temperature creep rupture behavior of Ni-based Alloy718 steels jointed by friction welding wasinvestigated at the elevated temperatures of 550 to $700^{\circ}C$ under constant stress conditions. The creep rupture characteristics such as creep stress, rupture time, steady state creep rate, and initial strain were evaluated. Creep stress has a quantitative correlation between creep rupture time and steady state creep rate. The stress exponents (n, m) of the experimental data at 550, 600, 650 and $700^{\circ}C$ were derived as 26.1, -22.4, 22.5, -18.5, 17.4, -14.3 and 6.9, -8.1, respectively. The stress exponents decreased with increasing creep temperature. The creep life prediction was derived by the Larson-Miller parameter (LMP) method and the result equation obtained is as follows: T(logtr+20)=-0.00148${\sigma}^2$-3.089${\sigma}$+23232. Finally, the results were compared with those of the base metal for Alloy718.

• 대한기계학회논문집A
• /
• 제33권10호
• /
• pp.1119-1124
• /
• 2009

This paper deals with the variability analysis of short term creep rupture test data based on the previous creep rupture tests and the possibility of the creep life prediction. From creep tests performed by constant uniaxial stresses at 600, 650 and $700^{\circ}C$ elevated temperature, in order to investigate the variability of short-term creep rupture data, the creep curves were analyzed for normalized creep strain divided by initial strain. There are some variability in the creep rupture data. And, the difference between general creep curves and normalized creep curves were obtained. The effects of the creep rupture time (RT) and steady state creep rate (SSCR) on the Weibull distribution parameters were investigated. There were good relation between normal Weibull parameters and normalized Weibull parameters. Finally, the predicted creep life were compared with the Monkman-Grant model.

• Journal of Biosystems Engineering
• /
• 제23권5호
• /
• pp.473-480
• /
• 1998

This study was performed to analyze the variation of various physicochemical factors related to the freshness of apple and tomato during post-harvest period. The total soluble solids content, uronic acid content, cell surface roughness. density, rupture deformation and rupture force were measured for 39 days at 7-day intervals for apple and for 11 days at 2-day intervals for tomato. respectively. The cell surface roughness of apple increased with the elapsed time, while the rupture force decreased. In case of tomato, uronic acid content, density and rupture deformation increased with the elapsed time whereas the rupture force decreased. Both apple and tomato exhibited the significant correlations among those physicochemical factors.