• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.2
• /
• pp.365-369
• /
• 2016

The 350[km/h] catenary system was successfully opened in Honam high speed line. This 350[km/h] catenary system is firstly constructed in South Korea. Therefore the current collection performance of this system should be tested and evaluated by the authority. This paper describes the testings by running of HEMU-430X train and the evaluation criteria and result analysis to determine whether the performance of the catenary is good or not as a verification of catenary-pantograph interface. In detail, the contact force by pantograph, arcs by loss of contact and uplift amount of the catenary support were measured and discussed as a category of the current collection performance.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.3
• /
• pp.69-81
• /
• 1997

Up to now 5 Voith Sulzer paper machines with multi-layer headbox and Gapfor-mer are sucessfully running on papckaging papers. Linerboard, testliner and corugating medium is produced in the basis weight range from 105 to 275 $g/m^2$ at machine speeds up to 900 m/min. The nest one, starting up in Oct. ｀96 in Germany, will be the world＇s fastest paper machine for packaging papers. The 5.6 m wide machine is designed for a maximum operating speed of 1200 m/min. Approx. 220.000 tons of corrugating medium and testliner based on 100% waste paper in the basis weight range from 90 to 160 $g/m^2$ will be produced each year. An expansion stage planned for the future is intended to increase annual output to 280.000 tons. This machine will not only be the fastest one for packaging papers, it also comprises all described innovative key components which are available today in order to fulfill growing demands of the future with regard to quality and productivity. The concept of this advanced machine is shown in Fig. 9.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.9
• /
• pp.117-122
• /
• 1999

Track rubber parts has heat built-up as long as dynamic loading is applied from running tracked vehicles. Durability is required for rubber part to sustain the heat accumulation and heat exchange between rubber-metal assembly and environmental air and ground. For this research, the track assembly was divided into four parts i.e., bottom track shoe, upper track pad, pin busing and metal structure. Three rubber parts and metal structure were modelled and analyzed with MARC package program to obtain time-temperature data which was induced form mechanical work of tracked vehicles. heat accumulation data was obtained from special experiments under the room temperature of 25$^{\circ}C\;and\;35^{\circ}C$ to simulate the actual environmental conditions. From this research, it is cleared that the environmental temperature does not affect to the heat accumulation speed in rubber parts. Also, the heat built-up mechanism was clarified from the thermo-mechanical work based on numerical analysis and experiments.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2159-2164
• /
• 2002

This paper reports on the effects of additional factors on the engine friction characteristics. The total friction loss of engine is composed of pumping and mechanical friction loss. The pumping loss was calculated from the cylinder pressure, and the mechanical friction loss was measured by strip-down method under the motoring condition. The various parameters were tested. The engine friction loss was much affected by oil and coolant temperature. The low viscosity oil was very effective to reduce the friction loss, and friction modifier was very useful to reduce the friction loss at lower engine speed. The engine friction loss was varied with engine running time because of surface roughness decreasing and oil degradation. To prevent oil-churning effect, it was very important to maintain the proper oil level. The presented results will be very useful to understand friction characteristics of engine.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.861-865
• /
• 2001

Generally the noise and vibration characteristics of 4WD vehicle is closely related to the characteristics of driveline such as bending mode, torsional mode, unbalance and nonuniformity of propeller shaft. In this paper the 4WD vehicle which has body vibration problem in high speed driving condition was tested. The sources of the body vibration and its transfer path are investigated by experimental approach. According to the experimental assessment, the body vibration is caused by the nonuniformity of joint of propeller shaft. And this paper presents a kinematic model of a vehicle driveline for the optimization of a driveline characteristics. Finally the optimized result of the drive line has been verified through the experiment.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.157-164
• /
• 2011

Hybrid car can improve fuel efficiency using a power of motor that is generated during constant-speed or deceleration driving. The motor is located between engine and transmission. But, when voltage of main battery is low, fuel efficiency is low because the voltage can't run the motor. In this situation, this study observed fuel efficiency when using solar cell for assistance power. In order to verify a fuel consumption of hybrid car equipped solar cell for assistance power, the car was tested downtown driving. As hybrid car was equipped solar cell for assistance, fuel consumption was reduced 8.35 % at running air conditioner. And, at air conditioner doesn't work, fuel consumption was reduced 6.88 %. This point of view, CO2 is expected to reduce in similar proportion.

• Journal of Korea Ship Safrty Technology Authority
• /
• s.33
• /
• pp.12-31
• /
• 2012

수치 계산으로 고속 활주선의 저항 성능을 평가하기 위해서는 활주 상태에서의 항주자세 예측이 무엇보다도 중요하다고 할 수 있다. 항주자세의 변화가 큰 고속 활주선의 경우에는 활주 자세에 따라 선저 바닥면에서 나타나는 압력 변화에 의한 동적 부양력 변화가 크므로 단순히 정지 중 흘수를 기준으로 계산되어진 유체력으로 항주자세를 예측하기 보다는 자세 변화에 따른 동적 부양력의 변화와 이에 의한 자세 변화를 반복 계산을 통해 수렴시키는 것이 요구되어진다. 본 연구에서는 선형화된 자유수면 조건의 포텐셜 수치 계산으로 유체 동압력인 부양력을 계산해내고 이를 유체 정역학적 힘으로 간주하여 부력과 선체중량과의 힘과 트림 모멘트 평형 관계를 만족시키는 방법으로 반복적인 계산을 통해 수렴된 활주 자세를 얻어내었다.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.645-656
• /
• 2008

The operation of express train on the Seoul Metropolitan Subway Network is centered on the Kyungbu and Kyungin lines and the short section between Dongducheon station and Ganyung station which is 20.7km long. It is true that the needs of many customers who want to reduce their commuting hours by express train is not satisfied. This paper proposes that the operation of express trains be enlarged to Sungbuk station on Kyungwon line which comes to 34.9 km long, and to Yangsu station from Youngsan station on Jungang line. The type of operation is mixed one with high and low speed trains, which operates express train by use of existing siding tracks without improving facilities such as extra building of sidings. This pragmatic study is to apply the goal of reducing running time as express train and to suggest the selection of appropriate stops, effectivenes analysis of express train operation and formation of train diagrams to actual operation.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1614-1621
• /
• 2008

I accomplished a curve section traveling safety assessment analysis followed with railway condition for elevation of a curve passage speed of train utilizing trail analysis model. As a result, we confirmed that excess cant influence in badly traveling safety of train followed with cant change and cant shortage influence in badly traveling safety in case of large a curve radius and traveling safety of originally a curve section is most wrong. Also we confirmed that shortage of relief a curve length influence in badly traveling safety followed with change of relief a curve length.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1024-1028
• /
• 2008

The ballast, one of track components, plays an essential role as intermedium in transmitting train load to subgrade safely, and the deterioration of ballast directly effects the growth of track irregularity. In this study, we determined the main factor of ballast deterioration was miniature of ballast gravel caused MTT(Multiple Tie Tamper) works and accumulated traffic loads. To estimate the deterioration characteristics of ballast, we carried out field test through track construction for test and the model test simulating the actual operation environment, have done a comparative analysis with the sample's result(crushing rate) of high-speed railroad running actually.