• 한국전기전자재료학회논문지
• /
• 제11권10호
• /
• pp.878-884
• /
• 1998

We have investigated that the monodomain alignment of nematic liquid crystal (NLC) is obtained with polarized ultraviolet(PUV) light irradiation on polyimide (PI) surface. The LC alignment capability increases with increasing the UV light irradiation time. The polarized UV light irradiation on oblique angle of 60。 irradiated on PI surface rotated by 90。 at 10 min. after being normally irradiated on PI surface at 30 min., the generated pretilt angle of NLC is about 2.5。. The pretilt angle of NLC is attributed to the interaction between the LC molecules and the asymmetric triangular structure of polymer surface due to photo-depolymerization of polymer with the oblique UV light on PI surface. The voltage -transmittance and response time characteristics of photo-aligned twisted nematic (TN)-LCD with UV light irradiation time 60 min. were almost same in comparison with the rubbing-treated TN-LCD.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1385-1387
• /
• 1998

In this paper, we studied the electro-optical(EO) performance of photo-aligned twisted nematic(TN)-liquid crystal display(LCD) with oblique non-polarized ultraviolet (UV) light irradiation on polyimide (PI) surface. The monodomain alignment of photo-aligned TN-LCD is obtained with an angle of incidence of $85^{\circ}$ on PI surface. Also, we observed that the voltage transmittance and response time characteristics of photo-aligned TN-LCD is almost same compared to rubbing treated TN-LCD. Finally, we measured that the voltage-holding-ratio(VHR) of photo-aligned TN-LCD is almost same compared to rubbing treated TN-LCD.

• Tribology and Lubricants
• /
• 제20권6호
• /
• pp.314-321
• /
• 2004

Thermal distortion of non-contacting mechanical seals with inclined rubbing surfaces is affected by friction heat between seal ring and seal seat. The circulation fluid along the inclined rubbing surfaces maintains cooling friction heat and lubrication between the sealing surfaces of mechanical seal with an inclined surface. Mechanical seals with inclined sealing surfaces may be useful for reducing the frictional heating and power loss because of the introduction of cooling fluids to the sealing gap between seal ring and seal seat. From the FEM computed result shows that the thermal behavior and von Mises stress of sealing faces with an inclined angle 60 are much reduced in comparison of the conventional mechanical face seal with rectangular sealing surfaces.

• 한국전기전자재료학회논문지
• /
• 제18권7호
• /
• pp.635-640
• /
• 2005

In this paper, we have improved a novel high tilted optically compensated bend (OCB) (HTOCB) mode by using high tilt angle that was generated by the unique baking condition on the homeotropic alignment layer. The high tilt angle of liquid crystal (LC) was generated by new alignment process that tilt angle changed homeotropic state to homeogenous state using Hot-plate equipment; we obtained about $40\~50^{\circ}$ tilt angle with negative and positive dielectric anisotropy on the homeotropic polyimide (PI), and then LC tilt angle decreased as increasing baking temperature and time. At last, we obtained about $10^{\circ}$ with positive type NLC $({\Delta}n>0)$. Also, the LC tilt angle of positive type NLC $({\Delta}n>0)$ decreased as increasing rubbing strength at the same baking temperature and time. The novel LC operating mode (HTOCB) that used the high tilt angle by the new alignment method was improved. The response time of the novel HTOCB cell was faster than that of conventional OCB cell. We suggest that the developed the novel HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권6호
• /
• pp.576-580
• /
• 1997

In this paper, the viewing angle characteristics of amorphous (a) - twisted nematic (TN)-liquid crystal display (LCD) on poly(vinyl)cinnamate (PVC) surface with UV (ultraviolet) light irradiation were investigated. It was found that the threshold voltage increases with increasing the polymerization of PVC surfaces. We observed that the domain size of a-TN-LCD decreases with increasing the photo polymerization by increasing UV light irradiation time on PVC films. Also, we observed that the viewing angle of a-TN-LCD increased with increasing the photo polymerization on PVC surfaces. Finally, we consider that the viewing angle of a-TN-LCD on PVC surfaces is large compared to a-TN-LCD on polyimide (PI) surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.44-44
• /
• 2008

To date, rubbing has been widely used to align LC molecules uniformly. Although rubbing can be simple, it has fundamental problems such as the generation of defects by dust and static electricity, and difficulty in achieving a uniform LC alignment on a large substrate. Therefore, non contact alignment has been investigated. Ion beam induced alignment method, which provides controllability, nonstop process, and high resolution display. In this study, we investigated liquid crystal (LC) alignment with ion beam (IB) that non contact alignment technique on polyimide and electro-optical characteristics of twisted nematic (TN)-liquid crystal display (LCD) on the polyimide under various ion beam angles. In this experiment, Polyimide layer was coated on glass by spin-coating and Voltage-transmittance(VT) and response time characteristics of the TN cell were measured by a LCD evaluation system. The good characteristics of the nematic liquid crystal (NLC) alignment with the ion beam exposure polyimide surface was observed. The tilt angle of NLC on the PI surface with ion beam exposure can be measured under $1^{\circ}$ for all of irradiation angles. In addition, it can be achieved the good EO properties, and residual DC property of the ion beam aligned TN cell on polyimide surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.53-56
• /
• 2003

Blending effects for generating a pretilt angle in nematic liquid crystal (NLC) with negative dielectric anisotropy on the blended polyimide (PI) of homeotropic and homogeneous alignment surface were studied. Also, we investigated the EO performances for the advanced VA-$\pi$ cell using this homeotropic blended PI surface. A many decrease of tilt angle on the polymer surface to blend homeotropic PI and homogeneous PI with side chain type was measured, and the tilt angle decreased as blended ratio and rubbing strength increase. The blended effects for generating a pretilt angle were clearly observed, and the many decrease of tilt angle can be achieved by using the blended PI surface. The electro-optical (EO) characteristics using the advanced VA-$\pi$ cell using the homeotropic blended PI surface than that of conventional VA cell can be improved. We suggest that the developed advanced VA-$\pi$ cell on a homeotropic blended PI surface is a promising technique for the achievement of a fast response time, and a high contrast ratio.

• 한국전기전자재료학회논문지
• /
• 제16권9호
• /
• pp.826-832
• /
• 2003

Blending effects for generating a pretilt angle in nematic liquid crystal (NLC) with negative dielectric anisotropy on the blended polyimide (PI) of homeotropic and homogeneous alignment surface were studied. Also, we investigated the EO performances for the advanced VA- $\pi$ cell using this homeotropic blended PI surface. A many decrease of tilt angle on the polymer surface to blend homeotropic PI and homogeneous PI with side chain type was measured, and the tilt angle decreased as blended ratio and rubbing strength increase. However, a small decrease of tilt angle on the polymer surface to blend homeotropic PI and homogeneous PI with main chain type was measured. The blended effects for generating a pretilt angle were clearly observed, and the many decrease of tilt angle can be achieved by using the blended PI surface. The electro-optical (EO) characteristics using the advanced VA- $\pi$ cell using the homeotropic blended PI surface than that of conventional VA cell can be improved. We suggest that the developed advanced VA-$\pi$ cell on a homeotropic blended PI surface is a promising technique for the achievement of a fast response time, and a high contrast ratio.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.430-430
• /
• 2007

In general, polyimides (PIs) are used in liquid crystal displays (LCDs) as alignment layer of liquid crystals (LCs). Up to date, the rubbing alignment technique has been widely used to align liquid crystals on the PI surface, which is suitable for mass-production of LCDs because of its simple process and high productivity. However, this method has some disadvantages. Rubbed PI surfaces include the debris left by the cloth and the generation of electrostatic charges during rubbing process. Therefore, rubbing-free techniques for LC alignment are strongly required in LCD technology. In this experiment, PI was uniformly coated on indium-tin-oxide electrode substrates to form LC alignment layers using a spin-coating method and the PI layers were subsequently imidized at 433 K for 1 h. The thickness of the PI layer was set at 50 nm. The LC alignment layer surfaces were exposed to an $Ar^+$ ion-beam under various ion-beam energies. The antiparallel cells and twisted-nematic (TN) cells for the measurement of pretile angle and electro-optical characteristics were fabricated with the cell gap of 60 and $5\;{\mu}m$, respectively. The LC cells were filled with nematic LC (NLC, MJ001929, Merck) and were assembled. The NLC alignment capability on ion-beam-treated PI was observed using photomicroscope and the pretilt angle of the NLC was measured by the crystal-rotation method at room temperature. Voltage-transmittance (V-T) and response time characteristics of the ion-beam irradiated TN cell were measured by a LCD evaluation system.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.65-68
• /
• 1998

The mechanism of response time and viewing angle in in-plane switching ( IPS ) liquid crystal display ( LCD ) were investigated. The response time of photo-aligned IPS-LCD is fast compared with rubbing-aligned IPS-LCD on polyimide ( PI ) surface. The decay time $\tau$$\_$d/ is decreased with increasing the azimuthal anchoring energy A $\psi$ due to the steric interaction between the LC molecules and side chain of polymer. The viewing angle of IPS-LCD is increased by using photo-depolymerizatin method ; about ${\pm}$70$^{\circ}$at all direction.