• Elastomers and Composites
• /
• 제36권2호
• /
• pp.121-129
• /
• 2001

다양한 조건 하에서 고무판의 마찰계수를 폭정하기 위하여 수직하중, 미끄럼속도, 경도, 윤활 조건 및 고무판 두께 등을 변화시켜가면서 시험을 실시하였다. 시험에 사용된 고무판의 재질은 천연고무이며, 상대 부품은 강구를 사용하였다. 수직하중과 미끄럼속도는 마찰계수에 현저한 영향을 미치지 않았으며, 고무판의 경도가 높아지고 고무판의 두께가 얇아질수록 마찰계수는 감소하였다. 무윤활 시 마찰계수는 큰 편차를 보였으나, 오일 윤활인 경우 다른 조건에 관계없이 안정된 값을 나타내었다.

• Earthquakes and Structures
• /
• 제18권2호
• /
• pp.215-222
• /
• 2020

In this paper, slit steel rubber bearing is presented as an innovative seismic isolator device. In this type of isolator, slit steel damper is an energy dissipation device. Its advantages in comparison with that of the lead rubber bearing are its simplicity in manufacturing process and replacement of its yielding parts. Also, slit steel rubber bearing has the same ability to dissipate energy with smaller value of displacement. Using finite element method in ABAQUS software, a parametric study is done on the performance of this bearing. Three different kinds of isolator with three different values of strut width, 9, 12 and 15 mm, three values of thickness, 4, 6 and 8 mm and two steel types with different yield stress are assessed. Effects of these parameters on the performance characteristics of slit steel rubber bearing are studied. It is shown that by decreasing the thickness and strut width and by selecting the material with lower yield stress, values of effective stiffness, energy dissipation capacity and lateral force in the isolator reduce but equivalent viscous damping is not affected significantly. Thus, by choosing appropriate values for thickness, strut width and slit steel damper yield stress, an isolator with the desired behavior can be achieved. Finally, the performance of an 8-storey frame with the proposed isolator is compared with the same frame equipped with LRB. Results show that SSRB is successful in base shear reduction of structure in a different way from LRB.

• Earthquakes and Structures
• /
• 제2권1호
• /
• pp.1-24
• /
• 2011

During very strong earthquakes, seismically isolated buildings may experience large horizontal relative displacements, which may lead to poundings if an insufficiently wide clearance is provided around the building. This paper investigates, through numerical simulations, the effectiveness of using rubber bumpers, which could be attached at locations where it is likely to have impacts, in order to act as shock-absorbers. For the simulation of the dynamic behavior of such rubber bumpers during impacts, a nonlinear force-based impact model, which takes into account the finite thickness of the rubber bumpers, has been developed. Subsequently, a series of parametric analyses are performed to assess the effect of the gap size, the earthquake characteristics and the thickness, compressive capacity and damping of the bumpers. The stiffness of the moat wall is also parametrically considered during poundings of a seismically isolated building, as another potential mitigation measure for poundings of seismically isolated buildings.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.441-446
• /
• 2004

Mechanical systems with rubber parts have been used widely in industry fields. The evaluation of the physical characteristics of rubber is important in rubber application. Rubber material is useful to machine component for excellent shock absorbing characteristics. The impact characteristics of rubber were examined by experimental and finite element method. The impact test was conducted with a free-drop type impact tester. The ABAQUS/Explicit was used for finite element analysis. The effects of thickness and diameter of the cylindrical rubber structures were investigated. The impact absorbing ratio of the rubber material was studied order to compare the peak reaction force of the specimen which only contained aluminum against the specimen with the inserted rubber part.

• 대한기계학회논문집A
• /
• 제34권5호
• /
• pp.583-588
• /
• 2010

고무의 비선형성과 대변형으로 인해 코드-고무 복합재료의 정확한 거동을 파악하기는 어렵다. 코드와 고무 사이에 제 3 의 상을 가정해서 세 가지 상에 대한 모델링을 하기도 하지만 코드-고무 복합재료 계면의 두께와 물성을 결정하기 힘들다. 본 연구에서는 2 차원 일반화된 평면변형률요소와 평면변형률요소를 사용한 유한요소법을 적용하여 여러 가지 계면 두께를 갖는 코드-고무 복합재료의 유효탄성계수와 무차원 탄성계수를 구하였다. 고무물성은 네오-후크 모델을 적용하였고 여러 가지 하중상태와 몇 가지 계면 물성치에 대한 고찰을 하였다. 그 결과 계면 물성치와 계면 두께는 코드-고무 복합재료의 비선형성과 유효탄성계수에 영향을 미침을 알수 있었다.

• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1076-1086
• /
• 2003

The effect of a rubber mould on densification behavior of aluminum alloy powder was investigated under cold isostatic compaction. A thickness of rubber mould and friction effect between die wall and rubber mould were also studied. The hyperelastic constitutive equation based on the Ogden strain energy potential was employed to analyze deformation of rubber. The elastoplastic constitutive equation of Shima and Oyane and that of Lee on densification were implemented into a finite element program (ABAQUS) to simulate densification of metal powder for cold isostatic pressing and rubber isostatic pressing. Finite element results were compared with experimental data for densification and deformation of aluminum alloy powder under isostatic compaction.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.115-122
• /
• 2005

This study analyzed the characteristics of four kinds of bridge rubber pads and suggested how to determine the stiffness the pads. The stiffness of rubber pads can be estimated by a direct static test. In the procedure to estimate the stiffness of a pad, the dead load(preload) of a bridge and live load of a vehicle are considered. The polyurethane rubber pads have larger hardness than natural and chloroprene rubber pads and thus carry larger load bearing capacity. In addition, they showed higher stiffness with the same shape factor than the others and thus are more avaliable as for bridge bearings. Although natural and chloroprene rubber pads are elongated to large deformation in horizontal direction due to vertical loads, polyurethane rubber pads almost do not generate horizontal deformation due to vertical loads regardless to the thickness and hardness of the pads. Therefore, they do not need reinforced plate to restrict horizontal deformation.

• 대한기계학회논문집A
• /
• 제22권2호
• /
• pp.330-342
• /
• 1998

The effect of rubber mold on densification behavior of pure iron powder was investigated under cold isostatic pressing. The thickness effect of rubber mold was also studied. The elastoplastic constitutive equation based on the yield function of Shima and Oyane was implemented into the finite element program(ABAQUS) to predict compaction responses of metal powder under cold isostatic pressing. The hyperelastic constitutive equation based on Moony-Rivlin and Ogden strain energy potentials was also employed to analyze deformation of rubber mold. The coefficients of the strain energy potentials were obtained from tension and volumetric compression data of rubber. Finite element results were compared with experimental data for densification of pure iron powder under cold isostatic pressing.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.915-922
• /
• 2017

내열 및 내유성 고무복합체 특성연구(The study on the thermal and oil resistance rubber composite), 2016.[6] 연구에서는 고온($150^{\circ}C$, $175^{\circ}C$, $200^{\circ}C$) 조건의 고온촉진노화를 통하여 불소고무 복합체의 수명을 예측하였다. 일반적인 고무제품은 온도, 습도, 오존, 빛, 유제, 기계 및 전기적 응력 등의 특성저하 인자에 따라 다른 특성을 나타낼 가능성이 있으며, 이러한 문제를 해결하기 위하여 "내열 및 내유성 고무복합체 특성연구"[6] 연구에서 얻어진 고온촉진노화에 의한 수명 예측값과 저온촉진노화간의 인장강도 변화율 및 신장률 변화율 그리고 부피 변화율, 무게 변화율, 두께 변화율 및 열전도도를 비교 검토하였다. 검토 결과, 요구 한계수명은 모두 만족하였지만 고온촉진노화 결과와 저온촉진노화 결과 간 변화율에서 약간의 격차를 보였다. 이러한 변화율 격차가 일어나는 원인은 고온촉진노화에서는 노화 시 불소고무의 주사슬 분해로 인하여 인장강도, 신장률 감소 및 부피, 무게, 두께 증가가 일어나는데 비해 저온촉진노화에서는 $80^{\circ}C$에서 불소고무의 지속적 경화반응으로 인하여 인장강도, 신장률 및 부피, 무게, 두께 변화가 적게 나타났을 것으로 판단된다.

• Tribology and Lubricants
• /
• 제9권1호
• /
• pp.32-37
• /
• 1993

The equations are derived for the evaluation of the axial contact forces. The contact forces of rubber seals are analyzed as a function of the ratio of real contact length, the thickness of seal lip, the inclined angle of seal lip, and the interference between the edge of seal lip and the rotating inner ring. The experimental apparatus is developed for the test of seal lip contact force. The data for designing rubber seals are presented in terms of the ratio of real contact length, initial inclined lip angle, lip thickness. and the interference. The results obtained from the derived equation for the contact force are in good agreement with the experimental results.