• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1699-1701
• /
• 2005

Islanding phenomenon is undesirable because it lead to a safety hazard to utility service personnel and may cause damage to power generation and rower supply facilities as a result of unsynchronized reclosure. In order to prevent this phenomenon, various anti-islanding methods have been studied. Even though the slip mode frequency shift(SMS) method has been regarded as a highly effective anti-islanding method, the analytical design method of that was not cleared. This paper proposes a modeling of the SMS method using non-detection tone(NDZ) and evaluation of the method according to the test conditions of IEEE Std. 929-2000. The SMS method is derived analytically through modeling and verified visually by simulation and experiment.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.323-326
• /
• 2007

In this paper, the basic experiment, electrolytic cell design and basic manufacturing have been made to interpret the characteristics of Hydrogen-Oxygen-Gas-Generator. As for the detailed matters, the data research on basic technology on Hydrogen-Oxygen-Gas and analysis on characteristics of Hydrogen-Oxygen-Gas from basic experiment. Also the experiment of characteristics and comparative evaluation between constant current source using SCR converter from existing method and constant current source using new phase shift PWM control method converter. As results when it has injected constant DC current, we has compared Gas quantities by variable ripple frequencies using phase shift PWM control method converter. Therefore, in linear region, it has not different Gas quantities by constant DC current and by phase shift PWM control method converter. Also, it has increased Gas quantities wilder linear region when put ripple frequency at saturation region. Through, Gas quantities and input rower, it has acquired higher input power per Gas quantities at put pulse current. Therefore, when designing converter or inverter for electrolysis, which has ripple current.

• Journal of Energy Engineering
• /
• v.14 no.2 s.42
• /
• pp.123-132
• /
• 2005

An economic feasibility study is performed for the wind power generation with the examination of the wind speed and its distribution at Daekwanryung at which a wind fm is under construction. In this analysis, the distribution of wind speed is the key issue. The wind distribution which is usually expressed in terms of Weibull distribution with shape factor and scale factor needs to be reexamined to find the proper values of them according to the empirical wind speed data. After this kind of analysis is done, annual power generation of wind is calculated. Due to the lack of cost information, we applied EWEA data instead or the actual information from the site. The result would be of use to determine the 'reference price' of wind power under the current system of 'compensating subsidy for renewable power generation'.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.4
• /
• pp.477-486
• /
• 2001

Although the ports are actually competing with various strategies, the definition and structural understanding of port competitive power are not known very much. Therefore this study has launched from this fact, and has the objective of obtaining the structural model of the competitive power, and understanding the components of the port competitive power. The following are the results of the study. First, the process began by abstracting the components that composed the port competitive power through recent research, and grouping it by the most core components using the KJ method. Also, by using the FSM(Fuzzy Structural Modeling) method to understand the structure of the grouped components, and the structural model of the port competitive power was able to obtain as the result. Second, when analyzing the obtained structural model, port expenses, main trunk location, port congestion and port facility came out to be the most important component groups, and especially port expenses was the most effective component that effected all the other components overall. Third, the component groups that were relatively less important, effected by most of the other components, and located on the top level of the structure model were the hinterland accessibility, port ownership, customs duties speed, and large ship port entrance possibility etc. Fourth, the results of this study will be able to be used when establishing competing strategies for our country's ports by proposing the relatively important components with the port competitive rower considered.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.249-252
• /
• 2000

A new Smart rower IC's based on the Partial SOI technology was designed for such applications as mobile communication systems, high-speed HDD systems etc. A new methodology of integrating a 0.8${\mu}{\textrm}{m}$ BiCMOS compatible Smart Power technology, high voltage bipolar device, high speed SAVEN bipolar device, LDD NMOSFET and a new LDMOSFET based on the Partial SOI technology is presented in this paper. The high voltage bipolar device has a breakdown voltage of 40V for the output stage of analog circuit. The optimized Partial SOI LDMOSFET has an off-state breakdown voltage of 75 V and a specific on- resistance of 0.249mΩ.$\textrm{cm}^2$ with the drift region length of 3.5${\mu}{\textrm}{m}$. The high-speed SAVEN bipolar device shows cut-off frequency of about 21㎓. The simulator DIOS and DESSIS has been used to get these results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.904-912
• /
• 2007

In this paper, a broadband 4-way power divider which can be used from 20 MHz to 500 MHz in the V/UHF band is designed using transmission-line transformer and ferrite toroid. A 4:1 impedance transformer is realized and this 4:1 transformer is connected with bridge-type 2-way dividers to form a 4-way rower divider, Insertion loss of about 6.8dB, isolation of less than -20dB, and return loss of less than -15dB in most band of interest are measured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.263-266
• /
• 2004

The stochiometric mix of evaporating materials for the $ZnGa_2Se_4$ single crystal thin films were prepared from horizental furnace. The polycrystal structure obtaind from the power x-ray diffraction was defect chalcopyrite. The lattice costants $a_0\;and\;c_0\;were\;a_0=5.51\;A,\;c_0=10.98\;A$. To obtains the single crystal thin films, $ZnGa_2Se_4$ mixed crystal were deposited on throughly etched Si(100) by the Hot Wall Epitaxy (HWE) system. The temperates of the source and the substrate were $590^{\circ}C\;and\;450^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the double crystal X-ray diffraction(DCXD). Hall effect on this sample was measured by the method of van der Pauw and studied on carrier density and mobility dependence on temperature. In order to explore the applicability as a photoconductive cell, we measured the sensitivity($\gamma$), the ratio of photocurrent to dark current(pc/dc), maximum allowable rower dissipation(MAPD), spectral response and response time.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.1
• /
• pp.49-53
• /
• 2006

This paper specifies the new power supply paradigm converting 154kV voltage level into 22.9kV class with equivalent capacity using superconducting rower facilities and analyze the fault current characteristics with and without HTS-FCL (High Temperature Superconducting-Fault Current Limiter). Superconducting new power system is the power system to which applies the 22.9kV HTS cable in parallel to HTS transformer and HTS-FCL with low-voltage and mass-capacity characteristics replacing 154kV conventional cable and transformer. The fault current of superconducting new power system will increase greatly because of the mass capacity and low impedance of HTS transformer and cable. This means that the HTS-FCL is necessary to reduce the fault current below the breaking current of circuit breaker. This paper analyze the fault current and suggests the parallel HTS-FCL scheme complementing the inherent problem of HTS-FCL, that is recovery after quenching is impossible within shorter than a few seconds.

• Korean journal of applied entomology
• /
• v.45 no.3 s.144
• /
• pp.339-346
• /
• 2006

Total 90 species of medicinal plants were surveyed to see if they have any suppressive effects on the dinsity of M hapla at the exhibition field in the Chinan medicinal herbs experiment station. In 70 species including Achyranthes japonica, root-knot and/or egg sac of M. hapla was not found and these plants were planted in C. lanceolata field to check the degree of M. hapla infection. In 26 species including A. japonica, M. hapla infection was not observed. Simultaneously, 30 species were planted in pots to find out degree of infection by M. hapla. Dianthus chinensis, Rudbeckia bicolor, Sedum kantschaticum, Ricinus communis, Anemarrhena asphodeloides, Malva verticillate, Chelidonium majus, Sesamum indicum, Agrimonia pilosa, Geum aleppicum, Sanguisorba officinalis and Scrophularia buergeriana were free from infection. While the number of galls and density of M. hapla in soil were higher to high innoculation density, and the growth of C. lanceolata was rower.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.1
• /
• pp.228-238
• /
• 1996

The purpose of this study was to evaluate the effect of chacteristics of knit fabrics on the microclimate of the skin simulating system. To determine the effect of characteristics of knit fabrics, vapor state of sweat pulse was simulated in the closed system. Different contents of fibers such as cotton, wool and polyester with different yarn size and knit types were chosen for specimens. The changes of humidity and temperature of air layer in the simulated systems were measured. Buffering indices, $K_d$ and $\beta_r$, were determined by considering $\alpha_p, \DeltaP_{max}, t_{max}, and tan\beta$. Physical properties of knit fabrics such as thickness, porosity, air resistance and moisture vapor transport were measured. Results showed that vapor pressure of wool was lower than cotton or polyester This was attributed to the hydrophilicity of wool which absorbed moisture rather quickly and retained in the knit fabric. The time to decrease vapor pressure was faster for polyester than cotton or wool. As a result, $K_d$ was in the order of wool> polye, item> cotton. $\beta_r$ of wool was rower than cotton or polyester due to its lowers porosity and slower desorption rate. For the yarn size, $K_d$ was in the order of 80's> 60's> 30's; thinner and lighter yarn showed better water vapor transport property. For knit type, buffering capacity of single jersey was better than interlock knit fabric. Statistical analysis showed that the air permeability was the most influential factor far the water vapor transport properties.