• 한국정밀공학회지
• /
• 제24권6호
• /
• pp.78-85
• /
• 2007

In this study, we performed finite element analysis for the design of a medical centrifuge and two-types of centrifuge were compared with each other. The types of centrifuge are 2-arm straight type and 3-arm type. Structural analysis was done with respect to the change of the rotational speed of the rotor of a centrifuge. When the rotor of centrifuge was rotated, the von Mises stress of 2-arm straight type-rotor was compared with the von Mises stress of 3-arm type. The margin of safety was estimated from the result. We found the critical speed of centrifuge from the campbell diagram by modal analysis.

• 한국정밀공학회지
• /
• 제33권9호
• /
• pp.707-714
• /
• 2016

This paper describes analysis results of vibration characteristics and modal test for a small-scale quad-rotor drone. The rotor arm has a slender body with a propeller and motor at its tip. Rotor system generates excitation for an unbalanced mass. Therefore, the drone platform is involved in the possibility of resonance. For advance identification of the possibility of resonance, confirmation of eigen-mode being closest to the propeller operation range is necessary. Material properties of CFRP tubes used for the rotor arm were acquired by finding the natural frequency based on Rayleigh method. A simplified quad-rotor FE model consisting of rotor arm assembly with tip mass was built to perform numerical analysis, and a free-free boundary condition was applied to provide flight status. Modal tests for the actual platform with impact hammer instrument were performed to verify analysis results. Separation margin from hazardous eigen-mode was checked on the propeller operation range.

• 제어로봇시스템학회논문지
• /
• 제21권7호
• /
• pp.677-683
• /
• 2015

This paper proposes a helicopter direction adjustment system using barycenter shift. Most conventional methods for direction adjustment of uniaxial helicopters rely on the angle of inclination of the main rotor. However, the inherent burden of the bearing of the main rotor and serious abrasion of the helicopter using the above methods may results in loss of balance. To decrease abrasion and enhance the barycenter stability, the proposed method was used to shift the barycenter of the helicopter instead of the main rotor for direction adjustment. We set a biaxial ARM on a uniaxial helicopter to adjust the direction of ARM pointing as well as to realize stable direction control when the helicopter loses its balance. The method may enhance the landing safety of helicopters in emergencies. Uniaxial helicopters can be controlled under any environment by adjusting the motor parameters of the ARM which is dependent on the center of mass using neural network. The experiment results show that the helicopter can return to the starting position quickly under the external disturbance.

• Transactions on Control, Automation and Systems Engineering
• /
• 제4권1호
• /
• pp.17-22
• /
• 2002

Endoscopes for industrial and medical fields are expected to have multi degree-of-freedom (DOF) motions. A multi-DOF ultrasonic motor we developed consists of a spherical rotor and a bar-shaped stator, and the rotor rotates around three perpendicular axes using three natural vibration modes of the stator. In this study, a multi-DOF unilateral master-slave system for active endoscope using the multi-DOF ultrasonic motor is developed. The configurations of master and slave arms for active endoscope are similar, so that an operator can easily handle the master-slave system. First, driving characteristics of the multi-DOF ultrasonic motor are measured in order to design the slave arm and its controller. Next, the master arm and the slave arm are designed. Then, the unilateral feedback controller for the master-slave system is developed. Finally, the motion control tests of rotor are conducted. As a result, the possibility of the endoscope is confirmed.

• Composites Research
• /
• 제33권3호
• /
• pp.133-139
• /
• 2020

본 연구에서는 복합재료가 적용된 쿼드콥터의 진동 특성을 분석하고, 공진에 대해 회피 설계 및 해석을 수행하였다. 로터-암의 파이프가 복합재료로 구성된 상용 쿼드콥터의 플랫폼을 모사하고 상용 해석 프로그램을 이용하여 진동 특성 분석을 하였다. 실제 적층 배열을 해석에 적용하고, 참고 문헌과의 비교를 통해 신뢰성을 판단하였다. 그리고 모터의 가동범위 내에 특정 모드의 고유 진동수가 포함되는 것을 확인하였다. 기존 모델에서 적층 배열, 로터-암의 길이, 두께의 총 3가지의 변수를 선정해 공진 회피 설계를 수행하였다. 공진 회피 설계의 3가지 변수에서 각 해석의 결과를 비교한 후, 공진 회피 설계의 효율성 측면에서 방향을 제시하였다.

• 한국정밀공학회지
• /
• 제5권2호
• /
• pp.23-32
• /
• 1988

A control system for improving the moving accuracy of robotic manipulators with elastic joints is devloped. The dynamics of manipulator system is splitted into two sub-dynamics; of arm-link and actuator rotor- link, which are coupled statically through joint torque. Two contorl loops are implemented respectively around both sub-dynamic systems. Computed torque algorithm with acceleration feedback is used for the arm-link control loop, and for the actuator rotor-link control loop PID algorithm is adopted. The resulting control system is tested through a series of computer simulation for a PUMA type manipulator, The reaults show good performance of the developed control system for wide range of joint stiffness and moving speed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.722-723
• /
• 2015

This paper presents characteristics Analysis of Outer Rotor type BLDC Motor. To reduce the cogging torque and to make the high back EMF constant of the motor, Not only magnetization directions of a permanent magnet are investigated, but also a tooth chamfer of a stator is optimized. The design and analysis results are verified with experimental results.

• 한국가시화정보학회지
• /
• 제11권2호
• /
• pp.12-17
• /
• 2013

A flow visualization technique was developed to analyze flow distribution inside a dishwasher in this study. Then, a new design plan was proposed to improve the efficiency of the dishwasher by the analyzed results and it was confirmed experimentally by the developed technique. Gas flow fields inside a drying duct of a tub for a drying process was investigated by a developed PIV (Particle Image Velocimetry) and a CFD (Computational Fluid Dynamics) method. Also, the flow visualization technique was developed for the liquid flow field of a rotor-arm system to propose the improved design idea. Also, interactions between liquid and gas were observed around the rotor-arm system. The two-phase flow was modified to the liquid flow field because laser sheets are refracted when pass through the two-phase flow. Thus, the flow visualization techniques was developed in this study to measure the instantaneous flow velocities in the liquid quantitatively.

• 한국지능시스템학회논문지
• /
• 제25권4호
• /
• pp.398-404
• /
• 2015

본 논문에서는 관성측정장치를 기반으로 블루투스 환경에서의 자율비행을 위한 멀티 로터형 헬리콥터에 대한 설계 및 성능을 제시하였다. 멀티 로터관련 다양한 연구가 진행되어오고 있긴 하지만 최근에는 다양한 서비스를 목적으로 짐벌이 장착된 헥사로터형의 헬리콥터에 대한 관심이 모아지고 있다. 따라서, 본 논문에서는 지상의 원격조정 PC나 고성능의 원격제어장치나 영상시스템과 같은 외부보조 시스템 없이 연구와 구조활동, 모니터링 활동을 수행할 수 있는 컴팩트하고 자율비행을 위한 헥사로터(hexa rotor)형 헬리콥터에 대한 하드웨어 및 소프트웨어를 소개하고자 한다. 제안한 시스템은 헥사로터 헬리콥터의 구조와 관성측정장치 관련 하드웨어 구성과 수학적 모델링 및 시뮬레이션 결과를 각각 제시하였다. 또한, IMU 구현을 위하여 MCU(ARM-cortex) 보드를 장착하여 각 로터의 회전과 관성 측정장치의 입력신호에 대한 상태를 제어할 수 있도록 하였다. 그리고 시스템 시뮬레이션과 실험을 통한 시스템의 성능을 각각 검증하였다.

• 한국자기학회지
• /
• 제25권6호
• /
• pp.198-202
• /
• 2015

본 논문은 서비스 로봇관절 구동에 적용되는 50W급 외전형 BLDC 전동기 의 코깅토크 최소화 설계에 관하여 기술하였다. 코깅 토크 저감 설계를 위해서 반응표면법을 이용하였으며, 반응표면법에 사용되는 관측자료는 유한요소법을 이용하였다. 끝으로 설계결과에 대한 타당성은 실험을 통해서 검증하였다.