• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.167-174
• /
• 2013

High speed rotor systems with magnetic bearings have been the subject of much research in recent years due to the potential for active vibration control. In this thesis, optimal design was conducted for an 8-pole heteropolar magnetic bearing used in the flexible rotor of a turbo blower. In connection with bearing stiffness, this optimal design process was conducted using a genetic algorithm(GA), which is based on natural selection and genetics. The maximum stiffness of the magnetic bearing-rotor was found by considering the critical speeds of the flexible rotor. As a result, the magnetic bearings were optimized to have maximum stiffness.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1291-1293
• /
• 2005

Switched reluctance motors have the advantage a high torque/weight ratio, as the large reluctance torque is made by salient poles of both stator and rotor, and a high reliability. On the other hand, the switched reluctance motors have the disadvantage of a large ripple torque which is made by salient poles. So the application for the industrial fields have been limited to special cases. This paper describes the design of a 12/8 switched reluctance motor using a enemy layer method of the asymmetry rotor. The design is focussed to reduce the torque ripple and radial force in the demanded value. The three dimension finite element analysis method(3D-FEM) was used for decides a enemy layer angle of the asymmetry rotor. This paper presents modifications of the rotor pole shape which reduces the torque ripple.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.585-592
• /
• 2009

The performance of screw compressor depends on lots of design parameters of rotor profile, such as length of seal line, wrap angle, blow hole, suction and discharge port size, number of rotor lobe, etc. The optimum rotor profile makes it possible to increase the compression efficiency with low energy consumption, and to minimize the loss of power. In this research, a new rotor profile design and performance analysis are done by computer simulation. It is expected that the volumetric efficiency is improved because the internal leakage is reduced due to the minimization of blow hole and clearance, and the stiffness of rotors is increased due to the reduction of length to diameter ratio. Also, the specific power consumption will be secured for use ranging from low to high operation speed.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.258-263
• /
• 2002

A numerical analysis using 2-D unsteady compressible program is conducted to explain characteristics of rotating stall such as rotating speed and number of stall cells in an one-stage axial compressor. Unlike an axial compressor which has only a rotor, in one-stage axial compressor a rotating stall is generated by rotor/stator interaction and tack pressure rising without any artificial disturbance and modeling. As a back pressure is raised, the separation of suction side at blades is increased uniformly, but because of the discrepancy of blockage effect by stator, the disturbances are generated to form a stall cell. Once the stall cell is formed, regularly the stall cell are rotating through rotor blades. When the speed of rotor is design speed the rotating speed of stall cell is $83.3\%$ of rotor rotating speed. When the speed of rotor is $80\%$ of design speed, the speed of rotating stall is $88.2\%$ of rotor speed. The number of generated stall cell are also varied for rotor speed and back pressure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.24-31
• /
• 2001

An axial-type turbine design technology is developed. In order to design one-stage turbine, the preliminary design method is applied, and then design parameters are chosen after analyzing gas properties within the turbine passage using the streamline curvature method. Stator blade is designed using C4 profile, and rotor blade is designed using shape parameters. Stator is manufactured as an integral type and rotor is manufactured to be disassembled from the disc for changing blade incidence angle. The output power from the rotor is measured with various RPM and input power. Experimental results show that the maximum efficiency of turbine rotor is obtained on the design point, and the output power is proportionally decreased with the negative incidence angle even the test turbine is a reaction turbine. The efficiency of turbine rotor is decreased to 5% by $7.5^{\cire}$ negative incidence angle from the designed value.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.80-86
• /
• 2019

The gerotor type device is mainly used in low-speed, high-torque hydraulic motors, and is also applied as a small priming hydraulic pump. For this reason, many studies have been conducted to increase the efficiency of the gerotor pump. In this paper, we propose a new tooth profile design method different from the existing method. The new tooth design is made by modifying the tooth surface using the amplification function of the trajectories, created along the inner and outer rolling circles around the base circle. The shape of the mate rotor is then created using rotation simulation techniques. Such shapes are described as hypercloid. The designed hypercloid rotor is compared with the existing trochoid rotor, and the characteristics of the parameters and volumetric displacements are analyzed. Through this process, the optimum design with larger volumetric displacement than the existing rotor is achieved.

• Journal of KSNVE
• /
• v.5 no.2
• /
• pp.257-264
• /
• 1995

We designed the cutter profile for symmetric screw rotor and did vibration experiment of screw rotor manufactured by the designed cutter profile. The results of this study are summarized as follows. (1) We designed the cutter profile of screw rotor (4-6)(5-6) by using numerical analysis program. (2) The maximum amplitude and variation of amplitude of 5-6 profile rotor are about 30 - 36.7% and 10 - 25% smaller than those of 4-6 profile rotor, respectively. (3) As the angular velocity of rotor changes from 100 to 300 rpm, the vibration of X, Y axis in driving shaft of 5-6 profile rotor is about 10 - 20% smaller than that of 4-6 profile rotor.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.3
• /
• pp.5-11
• /
• 2012

This study is to develop a 1kW-class horizontal axis wind turbine(HAWT) rotor blade which will be applicable to relatively low wind speed regions in southwest islands in Korea. Shape design of 1kW-class small wind turbine rotor blade is carried out using a blade profile with relatively high lift to drag ratio by blade element momentum theory(BEMT). Aerodynamic analysis on the newly designed rotor blade is performed with the variation of tip speed ratio. Power coefficient and pressure coefficient of the designed rotor blade are investigated according to tip speed ratio.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.3 s.36
• /
• pp.7-13
• /
• 2006

Shape optimization of a rotor blade in a single-stage transonic axial compressor has been performed using a response surface method and three-dimensional Navier-Stokes analysis. Two shape variables of the rotor blade, which are used to define a blade skew, are introduced to increase an adiabatic efficiency. Throughout the shape optimization of a rotor blade, the adiabatic efficiency is increased to about 2.2 percent compared to that of the reference shape of the stator. The increase in efficiency for the optimal shape of the rotor is due to the pressure enhancement, which is mainly caused by moving the separation position on the suction surface of rotor blade to the downstream direction.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.57-60
• /
• 2003

This Paper contains the development procedure of Mach small-scaled composite rotor blade for helicopter articulated rotor system. This mach small-scaled composite blade design is conducted by using CORDAS program developed by KARI. The Dynamic analysis for an articulated rotor system with this blade is conducted by using FLIGHTLAB which is commercial software for helicopter analysis. Also the optimizing procedure of iterative design was described. The designed composite blades were manufactured after establishing the effective curing method. For small-scaled rotor test, strain gauges were embedded in composite blade spar to obtain bending & torsion strain value. To verify sectional properties of a blade, the bench test is accomplished. After comparing a designed data and tested data, Dynamic Calculation was repeated using tested data. Through this research, experiences of mach small-scaled composite blade development were accumulated and will be applied to the related research field.