• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.912-914
• /
• 2002

Single phase SRM(Switched Reluctance Motor) can not be started by itself and torque ripple is more generated than multi-phase SRM. But it is excited by single phase current and has very simple structure. Therefore it can be used in domestic appliance. Torque and speed of single phase SRM is controlled by adjusting exciting current and exciting section. Driver, which is composed with absolute encoder and DSP, is fabricated for control of exciting section on this paper. Then driving characteristics with exciting section is confirmed by using salient pole rotor type single phase SRM, which is fabricated in preceding research.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.604-606
• /
• 2002

Air-cored machines have a higher efficiency with high frequency. speed than iron-cored machine because of the iron losses which may produce too much heat as well as the copper losses occurred in the rotor winding. But air-cored machine is lower flux than iron machine. The nature of the machine from 'iron-cored' to 'air-cored' is a progressive feature in the machines. A general analysis of the fields that is applicable to all configurations is presented. Slotless machines have been applied for no ripple induced voltage. In this paper, slotless mahcines equipped with internal 4-pole amature winding. This paper pay attention to analyze flux density of air-cored and iron-cored synchrous machine analytically and compare flux density of aired-cored machine to iron-cored machine.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2230-2235
• /
• 2011

The purpose of this paper is to provide the unbalanced magnetic force and vibration mode comparison between two large interior permanent magnet machines(IPM) with different pole-slot combination considering stator and rotor eccentricity. Due to the punching tolerance, the mixed eccentricity of air-gap is inevitable. It will generate the asymmetric magnetic flux density in air-gap, which makes the unbalanced magnetic pull and vibration. The study is focused on the unbalanced magnetic force and their harmonic components according to eccentricity conditions such as static, dynamic and mixed. When the high vibration is produced especially resonance, the obtained results provide clues what eccentricity condition occurs in the machine.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.23-24
• /
• 2013

In recent years, ISG (Integrated Starter and Generator) system receives a great attention for electric electrification of normal gasoline vehicle. As a cost-effect machine design, an ISG without a permanent magnet is considered. A 12slot-10pole field-excitation flux-switching synchronous machine (FEFSSM) is designed and analyzed via JMAG. The active parts such as the field excitation coil and armature coil are located on the stator. The rotor part consisting of single piece iron makes it more robust and suitable to apply for high speed motor drive system application coupled with reduction belt. The design target is the motor with a maximum torque of 40Nm, a maximum power of 10kW and a maximum speed of 14000 rpm. In this paper, design optimization method is proposed for high torque capability.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.7
• /
• pp.317-322
• /
• 2005

Advantages of switched reluctance motor(SRM) include a simple structure, the ability of operation in hash environments and under partial hardware failures, and a wide speed range. However design of SRM for industrial applications is very difficult because motor's inherent none-linearity and sensitivity of design parameter. In this paper, an optimal method for determining design parameters of a switched reluctance motor is researched. The dominant design parameters are stator and rotor pole arc and switching on and off angle. The parameters affecting performance are examined and selected using evolutionary computations and commercial CAD Program. The proposed design process is very fast. reliable and easy to access. The simulated design method proposed is compared with conventional procedure.

• 전기의세계
• /
• v.18 no.4
• /
• pp.7-15
• /
• 1969

In this method the condenser excite winding has the phase angle of 90 electrical degree, with the load winding in stator. The condenser excite wing is connected with the condenser while the load winding is with the full rectifer. Direct and quardrature axis components of rotating field winding are composed, of balanced two phase winding, and each one of them is connected with half wave rectifiers. Initically, small amount of lead current can be induced at the condenser excite winding by residual magnetism of rotor. The induced lead current forces the rotating field winding to be excited by synchronous alternating magnetic field. The speed electromotive force, there for, induced in rotating field winding shall electro magnetize the rotating field pole by rotating half wave rectifiers. In the case of the charging generator directly coupled with engines at the operation of wide range speed, the generated region, such as vehicles, aircraft, ships etc, is occured. In conclusion, we can take the advantage of, omitting of voltage regurator and current limiter for charging load and reducing the consumption of fuel using the generated region which can be devided in to Impossible generated region, Generated region, and suspension generated region.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.141-147
• /
• 1997

The variable speed drive system of a electric motor is popular in industry due to its economical aspect and simplicity of implementation, comparing with a steam turbine or the other engine driven. For a large pumping load like a feedwater pump rated about or more than 20,000㎾, a synchronous motor could be primarily considered. In this paper, we studied the modelling of a variable speed drive system consisted with a load commutated inverter(LCI) and a brushless sailent pole rotor synchronous motor(SM) using MATLAB/SIMULINK. Simulation was performed with a small SM motor parameters.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.333-336
• /
• 2008

3MW 풍력발전기용 발전기의 구조적 특성을 소개하고 회전자의 동특성 해석을 수행하였다. 이 발전기는 증속기를 사용하였으며 정격속도는 1459 rpm 이며 30% over speed trip 조건을 적용하여 설계되었다. 회전자 pole에 전원 공급 없이 자기장을 만드는 영구자석을 사용하는 형태로 구조는 간단하다. 발전기의 냉각방법은 공극을 냉각하기 위하여 팬을 이용하여 공기를 순환하며 고정자 외형에는 냉각채널을 부착하여 냉각수를 순환한다. 회전기계의 설계 시에는 반드시 진동을 고려하여 가능하면 진동을 줄이는 방향으로 설계가 되어야 하며 회전축 계의 설계에 있어서는 계의 강도, 위험속도, 불평형 진동응답 및 안정성 등을 고려하여야 한다. 본 논문에서는 물리설계를 기본으로 하여 설계된 발전기의 형상을 간단하게 설명하고, 발전기의 회전자를 상용 유한요소 해석 프로그램인 ANSYS 를 이용하여 해석을 수행하였다. 해석절차는 정적해석을 수행하고 다음으로 모드해석을 수행 하였다. 모드형상에 따른 주파수를 표기하고 해석 결과를 나타내었다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.286-292
• /
• 2008

Transverse flux machine (TFM) has been developed to drive a machine of large input power at low-speed. However, it has complicated structure and large torque ripple due to its inherent structure In this paper the characteristics of torque of a rotatory two-phase TFM are analyzed by using the 3-dimensional finite to element method and optimal design. This research shows that one of the effective design variables is the skew angle of permanent magnet. The skew angles of permanent magnet are optimized by using a Progressive Quadratic Response Surface Method (PQRSM). It also shows that the proposed optimal skew magnet not only increases average torque but also decreases torque ripple of a rotatory two-phase TFM.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.941-942
• /
• 2011

A thermal equivalent circuit of IPMSM considering eddy current loss of PM and core loss of rotor is proposed. This thermal equivalent model is represented by the thermal resistances and thermal capacitances. In order to determine the factor of each parameter, a heating test is processed. Additionally, the eddy current loss of PM is calculated by a transient 3D finite element analysis. Finally, this thermal equivalent model is verified by a temperature test in a 25kW 12-pole/18-slot IPMSM with varying load.