• Journal of ILASS-Korea
• /
• v.6 no.4
• /
• pp.14-21
• /
• 2001

Rotary atomizer is widely used in practical application ranging from combustion, cooling, spray drying, agriculture, chemical system. Rotary cup atomizer has some advantages such as extreme versatility and liquid atomization successfully varying widely in viscosity. In rotary atomization, the feed liquid is centrifugally accelerated to high velocity and the liquid extends over the rotating surface as a thin film before being discharged into an atmosphere. The degree of rotary atomization depends upon peripheral speed, feed rate, liquid properties and atomizer design. An important asset is that thickness and uniformity of the liquid sheet can readily be controlled by regulating the liquid flow rate and the rotational speed. LDPA(Laser Diffraction Particle Analyser) and image aquisition system are used to measure drop size distribution and spray pattern. The atomization characteristics of the rotary cup atomizer is investigated experimentally by varing the liquid feed rate, rotary cup speed and air velocity for atomization. As a results, the effect of air velocity on the atomization characteristics such as drop size and spray uniformity is considerably greater than variation of those with liquid feed rate.

• YAKHAK HOEJI
• /
• v.35 no.4
• /
• pp.319-325
• /
• 1991

Aluminum phosphate gel was synthesized by reacting aluminum sulfate as a soluble aluminum salt to tribasic sodium phosphate in this study. The optimal synthesis conditions based on the yield of product were investigated by applying Box-Wilson experimental design. It was found that optimal synthesis conditions were as follows: Reaction temperature; $61~71^{\circ}C$, concentration of two reactants; 12.27~13.83%, concentration ratio of two reactants; [AI$_{2}$(SO$_{4}$)$_{3}$]/[Na$_{3}$PO$_{4}$]= 0.5, reaction time; 10.9~12.1 minutes, drying temperature of product; $60~72^{\circ}C$. Aluminum phosphate gel prepared by the optimal synthesis conditions was suspended with four types of natural and synthetic gums at the concentration of 0.375~1.5wv%. Their Theological properties of aluminum phosphate gels were examined with Haake-Rotovisco RV 20 rotational viscometer. It showed that the higher concentration of suspending agents and lower temperature, the higher viscosity. Aluminum phosphate gel suspended by pectin and agar showed plastic flow with rheopexy, and their gels suspended by sodium alginate and sod. CMC showed plastic flow with thixotropy.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.23 no.2
• /
• pp.117-128
• /
• 2005

Printing inks are basically dispersions of solid pigment particles in a vehicle. Pigment flocculation and/or colloidal aggregates created by thixotrope additives form a three- dimensional network in the inks. This structure complicates the flow behaviour of inks. However, if the internal structure is formed under control, the printing process will benefit from it because the ink must satify rheological requirements over a very wide range of shear conditions. The presence of internal structure results in the following prominent non-Newtonian rheological properties: viscoelasticity, yield stress, shear thinning and thixotropy. If the components of printing inks were changed, the rheological characteristics such as viscosity, yield stress, viscoelasticity and tack value were considerably varied. Thus, in this paper, the effects of changing the content of rosin modified phenolic resin on rheological properties of the vehicle will be studied. For that, the rheological properties were found by flow, yield stress, creep and oscillation measurements using Bohlin C-VOR Rotational Rheometer. And Emulsion rheology and its microstructure will be investigated.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.23 no.2
• /
• pp.1-14
• /
• 2005

Generally, printing inks are composed of pigment, vehicle and additive. Among others, the vehicle transfers the pigment to substrate and then binds it on the surface. So, rheological properties of the vehicle are an important factor which has influence on printability. Thus, in this study, rheology of the vehicle was investigated by using rotational rheometer according to molecular weight of resin. Also, emlusion rheology of water in oil type and its microstructure were examined with increasing the shear rate. Consequently, the following results were obtained: (1) By viscometric flow test, zero shear viscosity and shear thinning index of vehicle increased with increasing the molecular weight of resin. (2) By relaxation and creep test, relaxation time and retardation time of vehicle increased with increasing the molecular weight of resin. (3) By frequency sweep test, crossover point of vehicle increased with increasing the molecular weight of resin. (4) G' and G" of emlusions increased with increasing the molecular weight by amplitude sweep test. (5) The shape of water drop in emlusions was changed to the capillary tube.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.754-759
• /
• 2004

We have studied the fringe field switching (FFS) mode with the positive dielectric anisotropy for the fast response time. The factors such as the physical properties of the LC, the cell gap, and the rubbing angle were critical for the fast response time of the FFS mode. The response time became 10 ms faster when the rotational viscosity of the new LC is 20 mPa.s lower than the conventional LC. When the cell gap changed from 3.6 ${\mu}{\textrm}{m}$ to 3.0 ${\mu}{\textrm}{m}$, it was possible to achieve the total response time and response times associated with grey-to-grey transitions under 16 ms. And the response times including grey-to-grey transitions become fast as the rubbing angle decreases.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.1
• /
• pp.45-59
• /
• 2011

According as gradually increasing the demand for Eco-friendly products it has been progressed fairly development at a field of printing and printing inks. The Inks are used by soy oil beginning of ink industry for preventing environment. Now it is possible to make Eco-friendly inks with vegetable ester. So it is not necessary to use petroleum-based solvents for preventing environment. But There is some problems if using vegetable ester to inks. Vegetable ester has high solubility, it causes misting and low viscosity of the Inks. So resin is required high performance. Thus, in this paper, I studied about the properties variation of the Varnish and inks According to using the phenolic modified rosin ester and Soy oil Methyl esters. The compared in order of average molecular weight by the GPC method, rheological properties were found by rotational rheometer, and emulsion behavior were compared by high speed emulsification tester.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.109-113
• /
• 2005

We have studied a field sequential liquid crystal display (FSLCD) with electrically controlled birefringence (ECB). The ECB mode exhibiting fast response time, high transmittance, low operating voltage and adequate viewing angle. The positive liquid crystal (LC) is better than negative LC on dielectric anisotropy, birefringence and rotational viscosity. Because $K_{11}$ value out of the elastic coefficient of LC is also larger than $K_{22}$ value, decay time of VA-ECB is advantage. However, the transmittance & response time reduced with decreasing the cell gap. This drawback can be overcome by using LC with high ${\Delta}n$ but VA-ECB is occured loss of light efficiency because the $\gamma$ value increased by high ${\Delta}n$ of LC. Consequently, the HA-ECB mode is one of strongest candidate for FSLCD application.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.1-9
• /
• 2016

PURPOSES : The performance properties (indirect tensile strength, rutting resistance, and resilient modulus) of recycled aged CRM mixtures and their correlation with Superpave binder properties (viscosity, high failure temperature, $G^*sin{\delta}$, and stiffness) were investigated. METHODS: A series of Superpave binder tests was performed by using a rotational viscometer, DSR, and BBR to evaluate the performance properties. In addition, the CRM mixes were artificially aged through accelerated aging processes, and their properties were evaluated. The correlation between the properties of recycled aged CRM binders and the engineering properties of recycled aged CRM mixtures was experimentally determined. RESULTS : The rut depth values decreased and the ITS values increased with increasing high failure temperature. In general, the resilient modulus properties seemed to be poorly correlated with the high-temperature values, regardless of the aggregate source. CONCLUSIONS: The recycled aged CRM binders and mixtures can lead to satisfactory performance, and the properties of these binders are strongly correlated with the engineering properties of the mixtures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.582-585
• /
• 2004

Most of hard disk drives currently employ fluid dynamic bearing (FDB) for their rotor support. Stiffness of the FDB is affected by many design factors such as bearing clearance, fluid viscosity, and rotational speed. For the high rotating speed HDDs stiffness of the rotor is normally high enough to accomodate load disturbances. However small form factor HDDs that are to be operated in low power consumption are often designed with low stiffness rotors. Although the low stiffness rotor clearly benefits low power operation, it could damage the entire motor structure or head disk interface even by a light mechanical load disturbance such as shock or vibration. In addition, since a single channel HDD does not provide gram load equilibrium in axial direction the rotor could be tilted and make a hard contact to stator. A non-symmetric groove pattern could successfully compensate the tilted rotor angle during operation.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1324-1331
• /
• 2023

In the present work, we carried out a molecular dynamics study of the kinetic properties of the FLiNaK molten salt, as well as a detailed study of the structure of this salt melt. The high value of the self-diffusion coefficient of fluorine ions is due to the large number of Coulomb repulsions between the most numerous negative ions. The calculated values of shear viscosity are in good agreement with the experimental data, as well as with the reference data obtained on the basis of finding the most reliable data. The total and partial functions of the radial distribution are calculated. According to the statistical analysis, fluorine ions have the greatest numerical diversity in the environment of similar ions, and sodium ions with the lowest representation in FLiNaK, have the least such diversity. For the subsystem of fluorine ions, the rotational symmetry of the fifth order is the most pronounced. Some of the fluorine ions form linear chains consisting of three atoms, which are not formed for positive ions. The results of the work give an understanding of the behavior molten FLiNaK under operating conditions in a molten salt reactor and will find application in future studies of this molten salt.