• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.239-243
• /
• 2016

High temperature superconductor (HTS) magnet systems usually employ metal current leads which bridge between the cryogenic environment and room temperature. Such current leads are the dominant heat load for these magnet systems due to a combination of electrical resistance and heat conduction. HTS flux pumps enable large currents to be injected into a HTS magnet circuit without this heat load. We present results from an axial-type HTS mechanically rotating flux pump which employs a ferromagnetic circuit and a Cu-stabilized coated conductor (CC) HTS stator. We show the device can be described by a simple circuit model which was previously used to describe barrel-type flux pumps, where the model comprises an internal resistance due to dynamic resistance and a DC voltage source. Unlike previously reported devices, we show the internal resistance and DC voltage in the flux pump are not exactly proportional to frequency, and we ascribe this to the presence of eddy currents. We also show that this axial-type flux pump has superior current injection capability over barrel-type flux pumps which do not incorporate a magnetic circuit.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.5
• /
• pp.481-485
• /
• 2008

In stator windings of 6.6 kV rotating machine, corona discharge, surface discharge and internal discharge are caused mainly by internal voids and insulation degradation. Also, if partial discharge occurs in inner-part of stator windings, it will be happened electromagnetic pulses at wide frequency range. In case of discharge spark, electromagnetic pulse generated from discharge source, and we can detect it by using various RF resonators as an EM sensor. In order to detect these kind of electromagnetic sources, we have designed and fabricated planar patch sensor using CST MWS simulation, and also PD signals from artificial defected cable were measured by our proposed sensor. Furthermore, HFCT was used as a reference sensor and compared with our proposed new planar patch sensor.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1480-1482
• /
• 2005

The major causes of power quality deterioration are harmonic current through semiconductor switching device, due to use of nonlinear loads such as diodes rectifier or thyristor rectifiers. In response to this concerns, this paper presents a new control method of single-phase active power filter(APF) for the compensation of harmonic current components in nonlinear loads. In order to make the complex calculation to be possible, the single-phase system that has two phases was made by constructing a imaginary second-phase giving time delay to load currents. In the conventional method, a imaginary-phase lagged to the load current T/4(here T is the fundamental cycle) was made. But in this proposed method, the new signal, which has the delayed phase through the filter, using the phase-delay property of low-pass filter, was used as the second phase. As this control method is applied to the system of single phase, an instantaneous calculation was done rather by using the rotating reference frames that synchronizes with source-frequency than by applying instantaneous reactive power theory that uses the conventional fixed reference frames.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.29-36
• /
• 2017

In this study, the non-contact type bicycle generator system considering the recharge is developed to use the eco-friendly energy source when the bicycle is operating. The following three main factors are considered in this study. One of factors is that the intensity of the rotating magnet is in the range of 2,700~4,300 [Gause]. The next factor is that the separation distance of rotating magnet and bicycle rim is in the range of 1.5-3.0 mm. The last factor is that the pedaling speed is in the range of 55 RPM [Wheel speed 5.6Km]~150 RPM [Wheel speed 15.25Km] consirering with the 5 staged gear transmission. The obtained results are as followed. (1) The generator output voltage gradually increases from 3V to 10V with the pedaling speed increases, at the separation distance is less than 2.5 mm and the operating voltage of the LED lamp is generated at a pedaling speed of 60 RPM or more. (2) The output current of the generator increases from 20mA to 40mA with the pedaling speed increases, at a separation distance is less than 2.0 mm and the operating current of the LED lamp is generated at a pedaling speed of 60 RPM or more. (3) When the separation distance was 3.0 mm, the output voltage and current are significantly lower than those of the bicycle LED lamp is generated. (4) The charging time is expected to be 12.24 ~ 17.65 hours when the magnitude of the magnet is 3,400[Gauss] at a pedaling speed of 55 RPM or more. (5) As a result of this study, it is thought that the non-contact type bicycle generator system considering the recharge can replace the conventional friction power generation system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.11
• /
• pp.1519-1527
• /
• 2020

AGeneral radiation measuring devices have been developed in the form of spatial dose rate detection devices that measure dose rates to radioactive contaminant and 2D or 3D imaging devices for radioactive contamination information. Each of these radiation detection techniques has advantages. The advantages of both detection devices are necessary to minimize personal injury and rapid decontamination in the area of a radioactive accident. In this paper, we proposed a technique that can measure the dose rate and direction information about the radioactive pollutant source in real time using a detection sensor, a rotating body, and a directional shield for radioactive pollutant detection. The rotational-based detection device is configured to check the dose rate and direction using the location information of the rotator and measurement value. We proposed a measurement technique for vertical and horizontal directions through multiple holes. It was confirmed that the measurement error for direction information was less than 1% when detected in the horizontal direction.

• Journal of Biosystems Engineering
• /
• v.7 no.1
• /
• pp.17-32
• /
• 1982

The binders introduced in Korea were originally designed to be used for Japonica-type varieties which have relatively long stem and are highly resistant to shattering. In order to use it for Tongil varieties which are short and easy to be shattered, mechanical modifications are necessary to reduce a grain loss incurred during binder operation. This study was intended to investigate analytically and experimentally the major sources of grain losses caused by three kinds of binders now introduced in Korea. Actual modification for each of three binders was done and experimentally compared to see if any improvement on grain loss was achieved. The results obtained in this study are summarized as follows; 1. It was required that the power transmission of binder should have a shifting mechanism so that velocities of pick-up and traveling units could be changed independently as desired according to the Japonica-type and Tongil varieties. In other words, the desired velocity of traveling unit should be obtained by shifting the transmission and the velocity of pick-up unit should be selected by reaping clutch according to the variety independent of the velocity of traveling unit as shown in Fig. 6. 2. To reduce grain loss it was desired that the moving parts of the pick-up unit should have the lowest possible velocities in harvesting Tongil varieties, unless the reduction of the speed be hindered the conveyance of the material. Based on the study, it was concluded that the velocities of pick-up unit be reduced by about 35% of those of the existing units. 3. It was found that the lug at the upper rotating section of pick-up case gave a severe impact on the ears of rice to increase grain loss. The optimum design of pick-up case to protect the ears from the protruding part of the lug was recommended by the result of analysis of the trajectory of the end-point of lug at the position. 4. It was proved analytically and experimentally that pick-up unit at the lower-rotating part was the other important source of grain loss in pick-up and divider assembly. In order to reduce a grain loss incurred by lugs at their lower-rotating section, it was suggested to improve it by (1) widening the space between right and left lower-rotating section, (2) shortening the length of lugs, (3) enlargement of the angle between the pick-up case and ground-level, and (4) attaching guard to right and left dividers so that the rotating lug could not give a high impact to the paddy hill. 5. Pick-up and divider assembly of the original binder of three models studied was modified according to the suggestions that were given by the preliminary study. Field test showed that the modified binders were able to reduce grain losses by about 0.4-0.7 percentage points compared to those without modification.

• Journal of the Korean earth science society
• /
• v.38 no.4
• /
• pp.263-268
• /
• 2017

The determination algorithm of the location of a line source with strike and dip using the gravity gradient tensor on a single profile is proposed. We already proposed the determination of strike and dip in the previous paper and then, now we improved the algorithm to locate a line source after determining strike and dip. The strike and dip of the line source can be determined by rotating the gravity gradient tensor matrix as reducing 2 independent components. Using the ratio of remaining 2 components, the location can be determined by the least square manner of the pointing vectors on each observation point. A synthetic model is tested for proving the usefulness of the proposed algorithm.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.121-128
• /
• 2006

Magnetic survey flights by helicopters are usually parallel to the topographic surface, with a nominal clearance, but especially in high-resolution surveys the altitudes at which observations are made may be too variable to be regarded as a smooth surface. We have developed a reduction procedure for such data using the method of equivalent sources, where surrounding sources are included to control edge effects, and data from points distributed randomly in three dimensions are directly modelled. Although the problem is generally underdetermined, the method of conjugate gradients can be used to find a minimum-norm solution. There is freedom to select the harmonic function that relates the magnetic anomaly with the source. When the upward continuation function operator is selected, the equivalent source is the magnetic anomaly itself. If we select as source a distribution of magnetic dipoles in the direction of the ambient magnetic field, we can easily derive reduction-to-pole anomalies by rotating the direction of the magnetic dipoles to vertical.

• Elastomers and Composites
• /
• v.39 no.2
• /
• pp.131-141
• /
• 2004

The recycling of waste XLPE(crosslinked polyethylene), which is a major source of scraps from high voltage power transmission cables, has been discussed. The waste XLPE scraps were ground into fine powder with various sizes from less than $100{\mu}m$ up to about $1000{\mu}m$ using two types of tailor-made pulverizers. The compounds were prepared in a modular intermeshing co-rotating twin screw extruder at various conditions such as different compositions, types and powder sizes of waste XLPE, screw configurations and various polymer matrices (LDPE, HDPE, PP, PS). The mechanical and rheological properties and the fracture surface or the compounds were investigated. It was found that an improved impact strength was obtained from the compound with white XLPE powder pulverized from the scraps without outer/inner semi-conductive layers. Generally, the impact strength increases with the content of XLPE but decreases with the size of XLPE. Especially for LDPE, the extrusion was possible up to 80 wt% loading of XLPE. Also, the impact strength increases with the number of kneading disc blocks in the given screw configurations. The melt viscosity of the compounds increases with increasing XLPE loading. However, the higher shear thinning behavior of the compounds at common shear rates implies proper processibility of the compounds. In addition, the impact strength for other polymer matrices used increases with XLPE and it is noticeable that the impact strength of PS/XLPE (80/20 wt%) compound was improved twice that of pure PS.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.12
• /
• pp.1708-1715
• /
• 2003

An experimental study was made of turbulent separated and reattaching flow over a backward-facing step, where unsteady wake was generated by a spoked-wheel type wake generator with cylindrical rods in front of the separated flow. The influence of unsteady wake was scrutinized in terms of the rotating speed of the wake generator (0$\leq$S $t_{H}$$\leq$0.4). A conditional averaging technique in corporation with SBF was employed to elucidate the influence of the unsteady wake on the large-scale vortical structures of the separated flow. Special attention was made during two-dimensional measurements of wall-pressure with or without unsteady wake. The wall-pressure fluctuations were used to predict dipole sound source by Curie's integral formula. It was found that the reduction of the dipole sound source was due to the reduction of turbulent kinetic energy by unsteady wake in the recirculation region.n.