• Korean Journal of Cleft Lip And Palate
• /
• v.3 no.2
• /
• pp.41-50
• /
• 2000

The alar base on the cleft side in unilateral complete cleft lip, alveolus and palate is markedly displaced laterally, caudally and dorsally, By incising the pyriform margin from the cleft margin of the alveolar process, including mucosa of the anterior part of the inferior turbinate, to the upper end of the postnasal vestibular fold, the alar base is released from the maxilla, A physiological correction of nasal deformity can be accomplished by careful reconstruction of nasolabial muscle integrity, functional repair of the orbicular muscle, raising and rotating the displaced alar cartilage, and finally by lining the lateral nasal vestibule, The inferior maxillary head of the nasal muscle complex is identified as the deeper muscle just below the web of the nostril, The muscle is repositioned inframedially, so that it is sutured to the periosteum that overlies the facial aspect of the premaxilla in the region of the developing lateral incisor tooth, And then, the deep superior part of the orbicular muscle is sutured to the periosteum and the fibrous tissue at the base of the septum, just in front of the anterior nasal spine, The nasal floor is surgically created by insertions of the nasal muscle complex in deep plane and of the orbicular muscle in superficial one, The upper part of the lateral nasal vestibular defect is sutured by shifting the alar flap cephalically, The middle and lower parts of this defect are closed by use of cleft margin flaps of the philtral and lateral segments, respectively, Authors stress the importance of nasal floor reconstruction at primary surgery and report the technique and postoperative results.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.114-120
• /
• 2016

This paper describes generating efficiency characteristics of the double acting Stirling engine/generator for domestic small-scale CHP (Combined Heat and Power) system. In small distributed generation applications, Stirling engine has competition from fuel cell, microturbine and etc. In order to be economical in the applications, a long life with minimum maintenance is generally required. Free piston Stirling engine (FPSE) has no crank and rotating parts to generate lateral forces and require lubrication. Double acting Stirling engine/generator has one displacer and two power piston which are supported by flexure springs. Two power pistons oscillate with symmetric displacement and are connected with moving magnet type linear generators for power generation from PV work. In experiments, 1 kW class double acting free piston Stirling engine/generator is fabricated and tested. Heat is supplied to hot end of engine by the combustion of natural gas and converted to electric power by linear generators which are assembled with power pistons. The electric parameters such as voltage, current and phase are measured with for variable flow rate of fuel gas. Especially, generating efficiency of FPSE is measured with three different measurement methods. Generating efficiency of the double acting Stirling engine/alternator is about 24%.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.78-87
• /
• 2018

This paper describes specular reflectance measurements of dielectric plates in three waveguide frequency bands: D-band (110-170 GHz), G-band (140-220 GHz), and J-band (220-325 GHz). The transmit (Tx) part of the proposed specular reflectance measurement system is stationary, while the receive (Rx) part and the material under test (MUT) holder are concentric-rotating with a 2:1 speed ratio for specular reflectance measurements. In specular reflectance measurements, the first step measures the specular reflection coefficients of an MUT and a metal plate on the MUT holder located at the center of the Tx and Rx parts, and the second step calculates the specular reflectance defined by the specular reflection power (i.e., intensity) of the MUT normalized to that of the metal plate. Multiple reflection effects between the Tx and Rx antennas and the MUT on the measured specular reflectance are minimized by averaging out the multiple specular reflectances measured with changing the separation distance between the two antennas by ${\lambda}/8$ intervals. Measurement results of the perpendicular-polarized specular reflectance of commonly used dielectric plates are verified by comparing those with the analytic results and show that the results measured over the overlapped frequency range of the D-/G-bands and at the boundary frequency of the G-/J-bands agree well with the results for the other band, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2625-2632
• /
• 2009

Recently, a speed control method of induction motor by vector control theory is applied to highly efficient industrial field. The speed sensors attached to motor are used for detection of rotating speed. In the case using speed sensor, the installation of cable for minimization of electric noise, weaken maintenance, increase of price are demerit. Therefore the study of speed sensorless vector control theory performed activity. The design of sensorless vector controller for induction motor using tabu search is studied. The proposed sensorless vector control for Induction Motor is composed of two parts. The first part is for optimizing the speed estimation with initial PI parameters. The second part is for optimizing the speed control with initial PI parameters using tabu search. Proposed tabu search is improved by neighbor solution creation using Triangular random distribution. In order to show the usefulness of the proposed method, we apply the proposed controller to the sensorless speed control of an actual AC induction Motor System. The performance of this approach is verified through simulation and the experiment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.10
• /
• pp.975-983
• /
• 2009

This paper presents the work being carried out in order to deduce hover performance of a small-scale single rotor blade as a preliminary study of a small coaxial rotor helicopter development. As an initial research, a test stand capable of measuring thrust and torque of a small-scale rotor blade in hover state was constructed and fabricated. The test stand consists of three parts; a rotating device, a load measuring sensor and a data acquisition system. Thrust and torque were measured with varying collective pitch angle at fixed RPM. Through this research, hover performance tests were conducted for a small-scale single rotor blade operating in low Reynolds number ($Re\;{\approx}3{\times}10^5$), as well as for verifying the test stand itself for acquiring hover performance.

• Journal of the Korean Society of Safety
• /
• v.34 no.6
• /
• pp.88-95
• /
• 2019

It has been only a few years since drones have been introduced to Korea, and as the use of drones has increased in industrial sites as well as in hobby activities, accidents such as workers' body parts coming into contact with rotating propellers have been occurring since 2016. Industrial accident cases are being filed. In the case of a remote control vehicle, if you release the remote controller in the event of an abnormal situation, it stops in place and no further danger occurs but in case of drones flying over the sky is different. Sudden motor stops during flight, uncontrolled changes in flight posture, loss of radio waves, loose propeller, etc, numerous factors can lead to accidents due to unintentional movements. Therefore, drone operators need safety knowledge as well as high knowledge about drones. However, drones with a weight of less than 12 kg can fly without a pilot's certification, and therefore, a minimum accident prevention measure is required. 10 accidents approved as industrial accidents since 2016, 23 accidents surveyed by general drone operator, 40 accidents surveyed by the Korean Consumer Resources Unfortunately for the purpose of writing this paper, drones are a new species and do not have many parameters for analysis but my experience has shown that the type of disaster does not deviate significantly. In addition, there is no paper that analyzes drone related industrial accidents not only in Korea but also in other countries. However, even if you watch an overseas drone accident video through YouTube, it is not much different from the case that occurs in Korea. I hope that this study will be of little help to all the drone pilots as well as the work safety of industrial drones used in industrial sites.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1077-1082
• /
• 2011

Ball joint is a rotating and swiveling element that is typically the interface between two parts. In an automobile, the ball joint is the component that connects the control arms to the steering knuckles by playing a role of bearing. The ball joint can also be installed in linkage systems for motion control applications. This paper describes the simulation strategy for a ball joint analysis, considering manufacturing process. Its manufacturing process can be divided into plugging and spinning. Then, the interested response is selected as the stress distribution generated between its ball and bearing. In this paper, a commercial code of NX DAFUL 2.0 using an implicit integration method is introduced to calculate the response. In addition, the gap analysis is performed to investigate the fitness. Also, the optimum design is suggested through case studies.

• 한국해양학회지
• /
• v.29 no.2
• /
• pp.83-94
• /
• 1994

Two-dimensional tidal and tidal residual currents in Chinhae Bay are investigated by field observations, hydraulic and numerical experiments. The results of hydraulic and numerical model experiments roughly coincide with the field measurements. Maximum tidal currents during the spring and neap tides in Kaduk and Kyunnaeryang channel and the central channel of Chinhae Bay are strong as 90 to 110 and 30 to 40 cm/s respectively, and strong tidal residual currents having numerous eddies take place. Maximum tidal currents during the spring and neap tides in the western and northern parts of the bay are weak as below 30 and 10 cm/s respectively, and also tidal residual currents are relatively weak. Tidal residual currents in the northern part of Kajo-do go toward the north, whereas the currents in the southern part move down the bay, and the currents rotating clockwise occur around Bu-do. The surface currents in the bay depend strongly on the wind and river inflow, and such phenomena are more remarkable during he neap tide than the spring tide.

• Journal of the Korea Society for Simulation
• /
• v.25 no.4
• /
• pp.53-63
• /
• 2016

This study aims to verify the feasibility of design by developing pressure flow-controlled swash plate type pump with the use of SimulationX, a computer analysis program. Developing analysis model based on design drawing data has a cost-saving effect because it is possible to figure out the effectiveness of design through the work and it never falls into repeated inaccuracies in the production process. Analysis model is developed in the following order. First, the structure of each part such as valve and rotating unit which have dynamic factor is analyzed and the modeling of single component is carried out, reflecting drawing data. Second, the modeling of pump assembly is carried out with the combination of each analysis model and a work is conducted to determine whether the modeling can perform pressure flow control function according to load condition smoothly based on design intent. At the end of the modeling process, the feasibility of design is verified by showing the parts which are moving as expected mechanism.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.1
• /
• pp.41-48
• /
• 2019

This paper deals with the design of the L-band rotary joint, which is a core part of the tracking radar system. The rotary joint is a part that is mounted on the rotating parts of the tracking system antenna, which smoothly transmits RF signals with minimizing signal insertion loss. To improve the insertion loss of rotary joint, 1) dielectric materials, 2) design of distribution ring and 3)dielectric shape are studied. The performance of proposed rotary joint is compared with the conventional product. The prototype rotary joint showed a max insertion loss of 0.68dB, that is improved about 46% compare with conventional product which insertion loss was 1.26dB.