• Journal of Advanced Marine Engineering and Technology
• /
• 제37권2호
• /
• pp.178-182
• /
• 2013

채굴이나 유사한 산업에서 버킷 회전형 소형 굴삭기가 협소한 공간 작업에 흔히 사용된다. 이러한 소형 굴삭기가 많이 개발이 되고 있지만 버킷회전부의 응력 해석 연구가 없었다. 본 연구에서 유한요소법과 Spare solver를 이용하여 소형 굴삭기의 버킷 회전부와 그 인접부의 응력 해석을 다양한 위상에서 수행하였다. 결론적으로 회전부의 연결부분에서 응력집중으로 인해 다른 부분의 평균 응력 1MPa보다 조금 높은 응력을 확인하였다. 특히 상대운동이 있는 버킷 핀과 회전 피니언 기어에서 각각 7.7MPa과 40MPa 응력을 보였다.

• International Journal of Fluid Machinery and Systems
• /
• 제9권2호
• /
• pp.182-193
• /
• 2016

Introduction of intermittent electricity production systems like wind and solar power to electricity market together with the deregulation of electricity markets resulted in numerous start/stops, load variations and off-design operation of water turbines. Hydraulic turbines suffer from the varying loads exerted on their stationary and rotating parts during load variations since they are not designed for such operating conditions. Investigations on part load operation of single regulated turbines, i.e., Francis and propeller, proved the formation of a rotating vortex rope (RVR) in the draft tube. The RVR induces pressure pulsations in the axial and rotating directions called plunging and rotating modes, respectively. This results in oscillating forces with two different frequencies on the runner blades, bearings and other rotating parts of the turbine. This study investigates the effect of transient operations on the pressure fluctuations exerted on the runner and mechanism of the RVR formation/mitigation. Draft tube and runner blades of the Porjus U9 model, a Kaplan turbine, were equipped with pressure sensors for this purpose. The model was run in off-cam mode during different load variations. The results showed that the transients between the best efficiency point and the high load occurs in a smooth way. However, during transitions to the part load a RVR forms in the draft tube which induces high level of fluctuations with two frequencies on the runner; plunging and rotating mode. Formation of the RVR during the load rejections coincides with sudden pressure change on the runner while its mitigation occurs in a smooth way.

• 한국디지털건축인테리어학회논문집
• /
• 제11권4호
• /
• pp.39-46
• /
• 2011

This Study is about the Axis used for creating forms of interior spaces in representative works of Peter Eisenman architecture. The plans, elevations, photos of interior spaces of his architecture were collected and analysed. In conclusion, the methods using axises were classified in the axises crossing right angle and the rotating axises crossing right angle. The rotating axis were divided into one-angle rotating and multi-angle rotating. The axises were rotated on the plan or rotated on the elevation. The axises crossing right angle were used for dividing, assembling, transforming and composing different proportions of rectangles in interior spaces. The rotating axises crossing right angle were used for creating divers forms such as triangle, quadrilateral, and polygon. The one-angle rotating emphasizes directions of axises in interior spaces. The multi-angle rotating emphasizes decentered directions in interior spaces. The parts created while crossing axises three-dimensionally were opened or filled. The axises were used dynamically and three-dimensionally for diversity of forms in interior spaces of Peter Eisenman architecture.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권1호
• /
• pp.20-25
• /
• 2002

Electrical damages to critical parts in rotating machinery have caused many machinery failures and hours of costly downtime. The problem of shaft currents generated in non-electrical machines has puzzled both users and manufacturers of these machines. The main solution for preventing electromagnetic type damage is to demagnetize all of the machinery parts, however this is costly and time consuming. Therefore a thorough investigation into the causes and physical characteristics of electromagnetic shaft currents is needed. In this paper, the self excitation theory was developed far a simple model, an axial flux Faraday disk machine surrounded by a long solenoid. Experimental tests were conducted to investigate the physical characteristics on an electromagnetic self excitation rig. The theory showed that the directions of both the shaft rotation and the coil turns should be identical if self excitation is to occur. From the tests, the electromagnetic type shaft current had both AC and DC components occurred at all vibration frequencies. This could point to a way to detect small instabilities or natural frequency locations by monitoring shaft currents.

• 한국공작기계학회논문집
• /
• 제13권5호
• /
• pp.110-117
• /
• 2004

In automatic welding process using a robot, seam tracking is one of the important parts. Sensor for seam tracking is divided broadly into two categories as non contact sensor and contact sensor. The arc sensor is one of the non contact sensors, and it can be applied in weaving arc and rotating arc welding process. In such the arc sensors, rotating arc sensor can be applied to high speed welding over tens of Hz. The decrease of self regulation by high rotating speed causes to improve accuracy and response of sensor. In this study, fuzzy controller was used to track the seam for the $CO_2$ arc welding which had unstable arc. It could be shown that the rotating arc sensor was better than the weaving arc sensor.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.165-169
• /
• 2007

The purpose of this study is to investigate the effect of rotating unbalance mass on vibration characteristics of the front axle. The power-train systemof the vehicle is composed of several rotating parts. These component parts should be properly balanced by the balancing machine, however,sometimes these have the unbalance mass which causes the critical vibration in the vehicle. Therefore, this study suggests the vibration improvement method based on reducing the unbalance mass through changing the assembly type between the companion flange and the constant velocity joints. In addition, the way to increase the inertia moment of the companion flange was proposed.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.75-80
• /
• 2006

This paper introduces the mechanism of the ESD(electrostatic discharge) in the HDD spindle system using FDBs(fluid dynamic bearings). When a HDD(hard disk drive) spindle system is rotating, triboelectric charging occurs in the FDBs through the friction between the lubricant and the rotating shaft or between the lubricant and stationary sleeve. And this electrostatic charge is accumulated in the rotating parts of the HDD spindle system because they are insulated from the ground by the lubricant. This research shows experimentally that the behavior of electric charge and discharge in the FDB spindle system is the same as that of a capacitor. It also measures the electrostatic voltage difference between the rotating and stationary parts in the FDB spindle system due to the change of humidity, supporting load and motor speed. This research shows that the control of ESD is required in the HDD spindle system using FDBs, because the electrostatic charge accumulated in the FDB spindle system may cause the breakdown damage of the GMR head and data loss consequently.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.968-974
• /
• 2004

Automakers have been forcing their suppliers to guarantee qualities of parts. Then, the suppliers have met the fundamental quality requirements such as dimensions and functions, but they could not sufficiently satisfy the automakers' noise requirements yet because automatic noise inspection systems were little successfully adopted In mass-production lines. This study tried to develop a system for automatically checking noise radiated from a rotating engine part and filtering parts emitting noise higher than criteria: the upper limits of a overall noise level or a noise spectrum. A commercial noise measurement system was used for measuring noise, and then the noise data was transmitted to a governing program through OLE(object, linking and embedding) functions. The governing program, belonging to a total noise inspection system managed the noise measurement and analysis. This system was successfully adapted for distinguishing bad parts according to the noise criteria.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.508-512
• /
• 2004

This paper described operation and vibration characteristics of 'Tail-Fan' performance test system. KARI(Korea Aerospace Research Institute) developed 'Tail-Fan' system as a kind of helicopter anti-torque system(ATS) and designed ATS performance test-rig for Tail-Fan system performance test. Test-rig consists of driving parts, supporting parts and rotating parts. For Tail-Fan system performance tests, firstly, test-rig operation tests were carried out for verification of design specifications. Secondly, natural frequencies of fan blade and test-rig were measured respectively. Lastly, to find the operation rotating speed for performance tests, vibration tests using accelerometers on tail gear box(TGB) were carried out. Through the fanplot and vibration test results, Tail-Fan performance test conditions to avoid a resonance were found and performance tests were well done safely.

• Journal of the Optical Society of Korea
• /
• 제15권4호
• /
• pp.340-344
• /
• 2011

Airborne infrared techniques have been used in wild land fire management for decades. This paper describes a kind of infrared scanning system based on a rotating drum with a tilted porthole underside the plane nose. This design increases the stability of the mechanism system, reduces air resistance and protects inner parts. Aberration characteristics of a tilted ellipsoid porthole are analyzed and an effective solution is invented which makes the system achieve $30^{\circ}$ field of regard. The system's ultimate value of modulation transfer function is near the diffraction limit, which indicates that the performance of the rotating optical system meets the imaging requirements.