• Preventive Nutrition and Food Science
• /
• v.6 no.1
• /
• pp.23-28
• /
• 2001

A study was carried out to establish a detection method of irradiated shellfish through thermoluminescence (TL). The TL intensity of first glow curves for irradiated bloody, freshwater, and short-neck shellfish increased from control until 5 kGy and increased slightly room 5 kGy until 10 kGy. Maximum TL temperatures of all irradiated samples tested were below 23$0^{\circ}C$, within temperature interval of 150~25$0^{\circ}C$ recommended for evaluation. Since just in control, glow curve ratios of G3 and G4 calculated from re-irradiated (1 kGy) bloody, freshwater and shortneck were over 0.5, detection in control was possible. However, as glow curve ratios after three months were below 0.5, detection by glow curve ratios after three months was impossible. Gl, which calculated from unirradiated samples, exhibited below 0.1, they were classified as unirradiated. In all samples, all the irradiated shellfish could be classified correctly as irradiated by hemaximum TL temperatures and shape of the second glow curve because those were shown in a lower temperature region than those of the first glow curve.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.21-24
• /
• 2003

The understanding of the mechanism of device degradation has been accomplished recently, for devices using $AlQ_3$ electron transport and emitter molecule. In this presentation the experimental evidence for the degradation mechanism of $AlQ_3$ based devices will be reviewed, showing that the hypothesis of an unstable $AlQ_3^+$ cation explains a large amount of experimental data. This hypothesis, however, explains not only the room temperature device degradation in time but also sheds light on temperature stability of OLEDs. Dependence of half-life of a series of devices with an emitter layer composed of a mixture of $AlQ_3$ and different hole transport molecules (mixed emitter layer) will be discussed when they are operated at elevated temperatures. These results can also be explained in the framework of an unstable $AlQ_3^+$ species. An OLED structure containing a doped mixed emitter layer will be described, which shows extraordinary stability, half-life of 1200 hours at operating temperature of 70 C and initial luminance of 1650 $cd/m^2$. We will also discuss a novel Black $Cathode^{TM}$ OLED with reduced optical reflectivity, which is also stable at elevated temperatures. The new cathode utilizes a conductive light-absorbing layer made of a mixture of metals and organic materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1033-1036
• /
• 2004

Si nanocrystallites thin films on p-type (100) Si substrate have been fabricated by pulsed laser deposition using a Nd:YAG laser. After deposition, samples were annealed at the temperatures of 400 to $800^{\circ}C$. Hydrogen passivation was then performed in the forming gas (95% $N_2$ + 5% $H_2$) for 1 hr. Strong violet-indigo photoluminescence has been observed at room temperature from nitrogen ambient-annealed Si nanocrystallites. The variation of photoluminescence (PL) Properties of Si nanocrystallites thin films has been investigated depending on annealing temperatures with hydrogen passivation. From the results of PL, Fourier transform infrared (FTIR), and high-resolution transmission electron microscopy (HRTEM) measurements, it is observed that the origin of violet-indigo PL from the nanocrystalline silicon in the silicon oxide film is related to the quantum size effect of Si nanocrystallites and oxygen vacancies in the SiOx(x : 1.6-1.8) matrix affects the emission intensity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.710-717
• /
• 2000

Tensile and fracture toughness tests of the cold-rolled STS 304 steel plate for membrane material of LNG storage tank were performed at wide range of temperatures, 11 IK(boiling point of LNG), 153K , 193K and 293K(room temperature). Tensile strength significantly increases with a decrease in temperature, but the yield strength is relatively insensitive to temperature. Elongation at 193K abruptly decreases by 50% of that at 293K, and then decreases slightly in the temperature range of 193K to 111K. Strain hardening exponents at low temperatures are about four times as high as that at 293K. Elastic-plastic fracture toughness($J_c$) and tearing modulus($T_{mat}$) tend to decrease with a decrease in temperature. The $J_c$ values are inversely related to effective yield strength in the temperature range of 111K to 293K. These phenomena result from a significant increase in the amount of transformed martensite in low temperature regions.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.10
• /
• pp.162-169
• /
• 2004

High temperature uniaxial compression tests in the alpha single phase region were carried out on the Ti -43mo1%Al intermetallic compound, in order to obtain oriented lamellar microstructure. The compression deformation temperatures and strain rates are from 1573k to 1623k and 1.0x10$^{-4}$ s to 5.0x10$^{-3}$ s, respectively. Fully lamellar microstructure was observed after the uniaxial compression deformation in a single phase region followed by cooling to room temperature. Lamellar colony diameter depended on strain rates and test temperatures. The diameter varied between 8601m and 300fm. Stress-strain curve showed a work softening and the size of lamellar colony diameter varied depending on peak stresses. This shows the occurrence of dynamic recrystallization. Texture measurements after the uniaxial compression deformation, showed the development of fiber during dynamic recrystallization. It is seen that the area for the maximum pole density existed in 35 degrees away from the compression plane. The texture sharpens with a decrease in strain rate

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.7
• /
• pp.1-7
• /
• 2010

The device performances of accumulation-mode Pi-gate pMOSFETs with different fin widths have been characterized at high operating temperatures. The device fin height is 10nm and fin widths are 30nm, 40nm, and 50nm. The variation of the drain current, threshold voltage, subthreshold swing, effective mobility, and leakage current have been investigated as a function of operating temperatures. The drain current at high temperature is slightly larger than at room temperature. The variation of the threshold voltage as a function of the operating temperature is smaller than that of the inversion-mode MOSFETs. The effective mobility is decreased with the increase of operating temperature. It is observed that the effective mobility is enhanced as the fin width decreases.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.3
• /
• pp.172-176
• /
• 2005

Modern automobiles are built with a steadily increasing variety of materials and semifinished products. The traditional composition of steel sheet and cast iron is being replaced with other materials such as aluminum and magnesium. But low formability of these materials has prevented the application of the automotive components. The formability can be enhanced by conducting the warm hydroforming using induction heating device which can raise the temperature of the specimen very quickly. The specimen applied to the test is A6061, A7075 extruded tubes which belong to the age-hardenable aluminum alloys. But in the case of A6061 age hardening occurs at room temperature or at elevated temperatures before and after the forming process. In this study the effects of the heating condition such as heating time, preset temperature, holding time during die closing and forming time on the hydroformability are analyzed to evaluate the phenomena such as dynamic strain hardening and ageing hardening at high temperatures after the hydroforming process.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.394-398
• /
• 2019

In this paper, the joining characteristics of GDC-LSM ceramics with Crofer 22 APU metal alloys was investigated at different brazing temperatures and holding times by reactive air brazing. Brazing was performed using Ag-10 wt% CuO filler, at three different temperatures (1000, 1050, and 1100℃ for 30 minutes) as well as for three different holding times (10, 30, and 60 minutes at 1050℃). The interfacial microstructures were examined by scanning electron microscopy and the joining strengths were assessed by measuring shear strengths at room temperature. The results show that with increasing brazing temperature and holding time, joint microstructure changed obviously and shear strength was decreased. Shear strength varied from a maximum of 100±6 MPa to a minimum of 18±5 MPa, depending on the brazing conditions. These changes were attributed to an increase in the thickness of the oxide layer at the filler/metal alloy interface.

• Aerospace Engineering and Technology
• /
• v.11 no.1
• /
• pp.91-97
• /
• 2012

The structural analyses and experimental results for the bellows of a gas-generator liquid oxygen shut-off valve were presented. The bellows experiences axial compression and external high pressure loadings at cryogenic temperatures. The analyses were performed using EJMA (Expansion Joint Manufacturing Association) standard and the commercial FE (finite element) analysis program, Abaqus v6.9, at room and cryogenic temperatures. The spring modulus, the induced stress and the expected fatigue life of the bellows were compared respectively. The effects by the contact and the material plasticity on the FE analysis results were also analyzed. Also, FE analyses related to a burst test were presented.

• Advances in concrete construction
• /
• v.9 no.4
• /
• pp.375-386
• /
• 2020

In the present study, the effect of basalt, glass, and hybrid glass-basalt fibers on mechanical properties and fracture behavior of self-compacting concrete (SCC) mixes have been assessed at room and elevated temperatures. To do so, twelve mix compositions have been prepared such that the proper workability, flowability, and passing ability have been achieved. Besides, to make comparison possible, water to binder ratio and the amount of solid contents were kept constant. Four fiber dosages of 0.5, 1, 1.5, and 2% (by concrete volume) were considered for monotype fiber reinforced mixes, while the total amount of fiber were kept 1% for hybrid fiber reinforced mixes. Three different portions of glass and basalt fiber were considered for hybridization of fibers to show the best cocktail for hybrid basalt-glass fiber. Test results indicated that the fracture energy of mix is highly dependent on both fiber dosage and temperature. Moreover, the hybrid fiber reinforced mixes showed the highest fracture energies in comparison with monotype fiber reinforced specimens with 1% fiber volume fraction. In general, hybridization has played a leading role in the improvement of mechanical properties and fracture behavior of mixes, while compared to monotype fiber reinforced specimens, hybridization has led to lower amounts of compressive strength.