• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.22-29
• /
• 2001

Plasma-sprayed coatings were prepared using by spray-dried Cr$_2$O$_3$ powder with and without MoO$_3$ addition. A reciprocal type tribe-tester was employed to examine friction and wear behavior of the specimens at room temperature. The worn surfaces of plasma spray coated specimens were observed by SEM. The results showed that friction coefficient of the MoO$_3$-added coatings were lower than those without MoO3 addition. However pure Cr$_2$O$_3$ coating showed the lowest wear loss at the self-mated test. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with MoO$_3$ addition.

• Bulletin of the Korean Chemical Society
• /
• 제13권1호
• /
• pp.45-48
• /
• 1992

A synthetic method for bis-carbonylation of bromo(bromomethyl)benzenes was described. Alkyl carboalkoxyphenylacetates were easily prepared by the carbonylation of benzylic and arylic bromide moieties in bromo(bromomethyl)benzenes with alcohols in the presence of $K_2CO_3,\;CH_3I$, and a catalytic amount of cobalt carbonyl under the atmospheric pressure of carbon monoxide at room temperature in good to excellent yields. The base played a decisive role in the selectivity of product and $K_2CO_3$ was the best one among bases used.

• 한국진공학회지
• /
• 제6권S1호
• /
• pp.27-33
• /
• 1997

Recently ion beam assistant deposition (IBAD) was successfully used to produce a dense ultra-adherent and pinhole-free hydroxyapatite (HAp) layer on alumina substrate. After that the HAp-coated alumina was immersed in 20ppm and 100ppm $AgNO_3$ solution at room temperature for 48 hours to carry out the ions exchange between $Ag^+\;and\;Ca^+$ in HAp. The obvious antimicrobial effect against E.Coli, P. Aeruginosa and S. Epidermidis was observed in the samples treated with 20ppm $AgNO_3$ Solution, In contrast to this the untreated samples did not show any bactericidal effect. Scanning electron microscope(SEM) study showed that Ag homogeneously distributed on the surface. X-ray diffraction (XRD) demonstrated that the surface structure in the samples without Ag was HAp whereas with Ag is HAp and AgCaP. It appears that silver ions exchange with calcium ions in HAp does not cause significant changes in the structure of HAp coatings.

• 폴리머
• /
• 제24권4호
• /
• pp.520-528
• /
• 2000

본 연구는 고형분 70%인 하이솔리드 아크릴 수지 (BMHA)를 합성하여, 환경친화성 도료인 하이솔리드 아크릴/폴리이소시아네이트 도료(BNHS)에 적용하고 그의 도막특성을 살펴본 것에 그 의의가 있다. BMHA는 새로운 형의 단량체로서 acetoacetoxyethyl methacrylate (AAEM)을 도입하고 여기에 n-butyl acrylate, methyl methacrylate 및 2-hydroxyethyl acrylate를 4원공중합시켜 얻었다. BMHA 합성에 있어서 T$_{g}$ 값이 낮을수록, AAEM의 양이 많을수록 각각 높은 전환율을 나타내었고, T$_{g}$값 고정하의 OH 값 변화에 따른 전환율은 큰 차이가 없었다. BMHA와 폴리이소시아네이트를 상온경화시켜 하이솔리드 BNHS 도료를 제조하고서 자동차 상도용 도료로서의 적합성 여부를 알아보기 위하여 도막물성 시험을 한 결과, BNHS내에 AAEM 도입 전후의 도막물성 비교시험에서 AAEM 도입후에 내마모성과 내용제성이 향상됨으로써 자동차 상도용 도료로서의 응용가능성을 보여주었다.다.

• 한국재료학회지
• /
• 제23권4호
• /
• pp.211-214
• /
• 2013

The effects of a Ni coating on the sensing properties of nano ZnO:Ni based gas sensors were studied for $CH_4$ and $CH_3CH_2CH_3$ gases. Nano ZnO sensing materials were prepared by the hydrothermal reaction method. The Ni coatings on the nano ZnO surface were deposited by the hydrolysis of zinc chloride with $NH_4OH$. The weight % of Ni coating on the ZnO surface ranged from 0 to 10 %. The nano ZnO:Ni gas sensors were fabricated by a screen printing method on alumina substrates. The structural and morphological properties of the nano ZnO : Ni sensing materials were investigated by XRD, EDS, and SEM. The XRD patterns showed that nano ZnO : Ni powders with a wurtzite structure were grown with (1 0 0), (0 0 2), and (1 0 1) dominant peaks. The particle size of nano ZnO powders was about 250 nm. The sensitivity of nano ZnO:Ni based sensors for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas was measured at room temperature by comparing the resistance in air with that in target gases. The highest sensitivity of the ZnO:Ni sensor to $CH_4$ gas and $CH_3CH_2CH_3$ gas was observed at Ni 4 wt%. The response and recovery times of 4 wt% Ni coated ZnO:Ni gas sensors were 14 s and 15 s, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1719-1721
• /
• 1996

This paper describes the thermally stimulated current(TSC) of PAAS spin coated film and the electrical properties of pre TSC measurement and after TSC test specimens. The TSC measurement were performed from room temperature to about $280^{\circ}C$ and the temperature was increased by $5^{\circ}C/min$ automatically. It shows that two peaks of TSC are observed at about $50^{\circ}C$ and about $160^{\circ}C$. Result of this measurement indicate that one peak; $50^{\circ}C$ is from alkyl group; other peak at $160^{\circ}C$ is due to alkyl and C-O group of PAAS. Addition to larger peak at about $160^{\circ}C$ is due to dipolemoment of PAAS film. This result is proved by DSC measurement of PAAS film. The electrical properties of pre and after TSC were measured by currant-voltage(l-V) characteristics. The current-voltage characteristics after TSC specimens are increased the conductivity. The electrical properties of pre-after TSC measurement specimen is in the middle of imidization of PAAS. Because of this result a thermal imidization was performed at $300^{\circ}C$ for 1 hour.

• 펄프종이기술
• /
• 제38권5호
• /
• pp.54-59
• /
• 2006

Paperboards used for linerboard of corrugated fiberboard box were coated with different concentrations of polylactic acid (PLA) solution and the effects of harsh environmental conditions such as high humidity and temperature (96% RH at $30^{\circ}C$ for up to 5 days), and freeze-thaw ($-20^{\circ}C$ for a day and then thaw at room temperature for 30 min) conditions on the ring crush (RC) strength of the boards were investigated. One to five percent PLA solutions were coated onto SC manila linerboard ($20{\times}27cm$) using a No. 20 wire bar coater and the ring crush strength was measured using a computer-controlled Advanced Universal Testing System in accordance with TAPPI Test Method T 822 om-93. The RC strength increased significantly when the concentration of coating solution increased and appreciable changes were found when the concentration increased from 0 to 2% (P<0.05). Similar pattern of results was found after 5-day storage at $30^{\circ}C$ and 96% RH. Although such highly humid condition increased moisture content in the samples up to 3.95 from 0.97 times, the RC strength decreased in the range from 29.9 to 48.5%. The freeze-thaw treatment increased the moisture content only up to 1.27% and the reduction in the RC strength ranged from 21.1 to 28.1 %. The results were promising: the samples coated with 5% PLA solution showed 29.9% reduction in the RC strength while that of control was 48.5% during highly humid condition stated above.

• Transactions on Electrical and Electronic Materials
• /
• 제10권2호
• /
• pp.58-61
• /
• 2009

The electrical stability of ZnO: Al thin films deposited on glass substrate by the RF magnetron sputtering method have been modified by a hydrogen annealing treatment and $SiO_2$ protection layer. AZO thin films were deposited at room temperature and different RF powers of 50, 100, 150, and 200 W to optimize the AZO film growth condition. The lowest value of resistivity of $9.44{\times}10^{-4}{\Omega}cm$ was obtained at 2 mtorr, room temperature, and a power level of 150 W. Then, the AZO thin films were annealed at $250-400^{\circ}C$ for 1 h in hydrogen ambient. The minimum resistivity obtained was $8.32{\times}10^{-4}{\Omega}cm$ as-annealed at $300^{\circ}C$. The electrical properties were enhanced by the hydrogen annealing treatment. After a 72 h damp-heat treatment in harsh conditions of a water steam at $110^{\circ}C$ for four representative samples, a degradation of electrical properties was observed. The sample of hydrogen-annealed AZO thin films with $SiO_2$ protection layer showed a slight degradation ratio(17%) of electrical properties and a preferable transmittance of 90%. The electrical stability of AZO thin films had been modified by hydrogen annealing treatment and $SiO_2$ protection layer.

• 한국염색가공학회지
• /
• 제28권2호
• /
• pp.92-100
• /
• 2016

To chemically prepare polypyrrole(pPy) coated fabrics(silk, cotton and nylon fabrics), the fabrics were first soaked in 0.4M oxidant $FeCl_3$/0.06M dopant anthraquinone-2-sulfonic acid solution for 5min at room temperature, and subsequently soaked in a 0.4M monomer pyrrole aqueous solution for 5min at room temperature. The content(wt%) of coated pPy in the coated fabrics was controlled by the number of treatments(these two steps). This study examined the effect of the number of treatments/pPy content on the sheet resistance, mechanical/bending properties and color behaviors of pPy coated fabrics. The coated pPy content, sheet resistance(${\Omega}$/square) and color strength(K/S) of pPy coated fabrics increased sharply with increasing number of treatments up to 20 times, while the increase slowed down afterward. The tensile strength, elongation at break and lightness($L^*$) decreased with increasing number of treatments. The tensile modulus and bending rigidity of coated fabrics increased significantly with increasing number of treatments/coated pPy content. This indicated that the flexibility of coated fabrics decreased considerably.

• Advances in nano research
• /
• 제2권1호
• /
• pp.23-56
• /
• 2014

The significant growth of the Si photovoltaic industry has been so far limited due to the high cost of the Si photovoltaic system. In this regard, the most expensive factors are the intrinsic cost of silicon material and the Si solar cell fabrication processes. Conventional Si solar cells have p-n junctions inside for an efficient extraction of light-generated charge carriers. However, the p-n junction is normally formed through very expensive processes requiring very high temperature (${\sim}1000^{\circ}C$). Therefore, several systems are currently under study to form heterojunctions at low temperatures. Among them, carbon nanotube (CNT)/Si hybrid solar cells are very promising, with power conversion efficiency up to 15%. In these cells, the p-type Si layer is replaced by a semitransparent CNT film deposited at room temperature on the n-doped Si wafer, thus giving rise to an overall reduction of the total Si thickness and to the fabrication of a device with cheaper methods at low temperatures. In particular, the CNT film coating the Si wafer acts as a conductive electrode for charge carrier collection and establishes a built-in voltage for separating photocarriers. Moreover, due to the CNT film optical semitransparency, most of the incoming light is absorbed in Si; thus the efficiency of the CNT/Si device is in principle comparable to that of a conventional Si one. In this paper an overview of several factors at the basis of this device operation and of the suggested improvements to its architecture is given. In addition, still open physical/technological issues are also addressed.