• 전기학회논문지
• /
• 제63권2호
• /
• pp.325-330
• /
• 2014

In order to operate trains both mainline railroad platform and metropolitan subway line platform, it is necessary to develop the door step equipment of the rolling stock regardless of low(500mm, mainline) and high level platforms(1,135mm, metropolitan subway line) because of the requisite door safety system. In this study, TMS-DCU interface is studied for low and high level railway platforms. As a result, Design circuit of TMS(Train Management System)-DCU(Door Control Unit) interface is suitable for telescopic sliding type doorstep unit to minimize damage to the carbody underframe of railway vehicles.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1270-1276
• /
• 2003

This paper describes an analytical method for wheel wear prediction. The outputs from vehicle dynamic software are used to calculation the wheel wear. Two calculation examples are shown for a high-speed line and a conventional line. Through the comparison of two cases, we can see the wheel wear characteristics on the conventional line and the high-speed line. The conventional line has many curved tracks that cause severe wheel flange wear. The influences of curve radius on wheel wear are also described considering the operational performance of the high speed trainset. A method of calculation using contact patch work model is presented for determination of the evolution by wear railway wheels.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.934-939
• /
• 2004

Railway wheel/rail contact conditions have an influence on dynamic behavior of rolling stock. If there are problems of incompatibility between wheel and rail, damages like wheel wear, wheel spalling, rail wear, etc are occurred. Especially wheel and rail profiles are important factor of vehicle curving performance, so compatibility study between wheel and rail has to be carried out preferentially, In this study, we have analyzed the compatibility between wheel and rail of KNR conventional line to improve the maintenance efficiency of wheel and rail. Thus we showed the results relating to wheel/rail geometric contact, vehicle running performances as the change of wheel/rail combination.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.66-71
• /
• 2006

A geometric contact conditions of wheel/rail affect the dynamic behavior of rolling stock. Mechanical force acted on the wheel/rail causes excessive wear and increase the maintenance cost. In this study, we have studied the dynamic behavior of the urban railway vehicle with new and worn wheel by VAMPIRE program. And we have tested the accelerations of wheelset on the conventional line. The results of simulation are compared with the measuring data of field test. It shows that the acceleration of worn wheel is greater than the acceleration of new wheel in the straight track line but on the contrary, the acceleration of new wheel is greater than the acceleration of worn wheel in curved track. That results explain that the new wheel is worn out greater than the worn wheel in curved track line and need to be maintained more seriously when running in curved track line.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.529-538
• /
• 2009

A trial run of locally-developed tilting train has been in process on Chungbuk line since the test vehicle was first produced. For the system stabilization, interface verification among the systems including track, structure, catenary and signaling system, not to mention the rolling stock, is very crucial. Therefore, in this study, the dynamic rail force of the tilting (Hanvit 200), high-speed (KTX) and general (Mugunghwa) vehicle caused by driving in transition curve track was measured. And, it compared the tilting response with the other by using the measured wheel load data in transition curve track, and then evaluated probability the range of wheel load fluctuation for the variable dynamic vertical and lateral wheel load. As a result, a range of wheel load by occured a change of cant from the high-speed and general vehicle which had fixed bogie structure was distributed throughout small deviation (${\Delta}8{\sim}13kN$). Otherwise, in case of the tilting train which was consisted of the pendulum bogie structure was distributed wide range about large deviation (${\Delta}25{\sim}28kN$) by changed of cant.

• 대한기계학회논문집A
• /
• 제37권6호
• /
• pp.723-730
• /
• 2013

기존선에서의 속도향상을 저해하는 요인은 매우 다양하지만, 그 중 분기기 통과속도 제한규정을 가장 대표적 사례로 손꼽히고 있다. 현재, 기존선 분기기의 직선측 최고 통과속도는 일반 선로의 차량 최고 주행속도에 비하여 낮은 속도로 제한되어 운행하고 있으며 분기기내에서 주행속도를 제한하는 것은 분기기 통과 시 철도차량의 주행안전성을 확보하는데 목적을 두고 있다. 본 연구에서는 대구도시철도공사의 분기기 가드레일에 대한 형상 변경사례를 기반으로 하여, 분기기에서의 차륜/레일 형상에 따른 기하학적 관계식을 이론적으로 검토하였으며, 개발한 VI-Rail 분기기 해석기법을 통하여 F10/F12 분기기에서의 가드레일 길이 변화에 따른 주행안전성 해석을 수행하여 그에 따른 영향을 살펴보았다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1388-1398
• /
• 2011

Air pollution in subway tunnel is primarily caused from the wear of metallic materials. As undesirable substance, PM(Particulate Matter) can especially harm the health of passengers and workers as well as clog the main parts of rolling stock such as inverters. To improve the air quality in subway tunnel, SMRT(Seoul Metropolitan Rapid Transit Corporation) has developed anti-pollution devices such as Magnetic Dust Collector, Vacuum Cleaner For Rail Road and Particulate Removing Sprinkler Vehicle. Introducing these mechanical devices, this paper is mainly devoted to explaining the characteristics of collected dust according to the result of particle-size analysis and componential analysis.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.43-52
• /
• 2010

In this study, the shapes of the wheel and rail are represented by using 3-dimensional surface functions with surface parameters and a 3-dimensional wheel-rail contact analysis is presented. A whole numerical solution of wheel-rail contact at tread and flange including 2-point contacts can be achieved with the proposed numerical algorithm. Kinematic characteristics such as variances of vertical displacement and roll angle, and variance of wheel radius difference for arbitrary yaw and lateral displacement of wheelset, are determined for the KTX wheel-rail pair as an example. The condition of yaw and lateral displacement occurring 2-point contacts to analyze derailment are compared between standard and worn wheels. Differences of contact characteristics between curved and straight rails are also analyzed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.748-753
• /
• 2004

Aluminum alloy is very useful material for high speed transportations due to its high strength and light weight characteristics. Especially because of a weight reduction a large extrustion of aluminum alloy carbody has been manufactured. This aluminum extruded panel is a hallow extruded panel. This shape and thickness is various by designer's sense and experience and VAW's profiles. So it is important to find an optimized shape and thickness of AEP. In this study we get the AEP's thickness to minimize a weight by applying an applying an optimization algorithm. The results of the study can be used as basic guidelines double-deck trains in the future.

• 한국철도학회논문집
• /
• 제9권5호
• /
• pp.618-623
• /
• 2006

Understanding the contact between wheel and rail is a starting point in railway vehicle dynamic research area and especially analysis for the contact geometry between wheel and rail is important. On the one hand, the critical speed as the natural characteristics of rolling-stock is generally tested on the roller rig. The geometrical characteristics of the wheel/roller contact on the roller rig are different from these of the general wheel/rail contact because the longitudinal radius of roller is not infinite compared with rail. Thus, in this paper we developed the algorithm to analyze the wheel/roller contact geometry of our roller rig which is constructed now and analyzed the difference between whee/roller contact and wheel/rail contact. In conclusion, we found that the yaw motion of wheelset and the roller radius influence the geometrical contact parameters in wheel flange contact area.