• 대한전기학회논문지
• /
• 제38권4호
• /
• pp.307-315
• /
• 1989

본 논문에서는 열간압연공정중 소재가 가열로에서 추출되어 조압연 공정을 마치기 까지 소재인 slab의 온도변화추이를 해석키 위하여 rolling process 상에서 온도에 영얄을 미치는 인자인 1) 대기중 복사 및 대류에 의한 냉각 2) 소성가공발열 3) descaling water에 의한 수냉각 4) rolling roll, 운반 roll과의 접촉냉각등 제요인에 관한 사항을 rolling process 상에서의 문제로 평가도입하여 해석하고저 하는 slab 표면에서의 경계조건 설정과 관련한 적용기법을 정립하였고 소재의 냉각 현상을 two dimensional transient heat flow문제로 취급, 유한차분방정식을 이용하여 해석하는 과정과 관련 rollinh작업을 sequence화 하여 적용하는 기법을 제시하였다. simulation 결과 계산치와 실계측편차 (${\pm}18^{\circ}C$)범위내에서 일치함을 제시하였고 또한 rolling event 별로 나타나는 온도하강 pattern이 실제의 압연상황과 잘 일치함을 제시하므로서 본 computer simulation 과정에서 적용한 가정, 조건, 물성치 등의 적정성 등을 입증하였다.

• 대한의용생체공학회:의공학회지
• /
• 제35권3호
• /
• pp.35-41
• /
• 2014

In this study, joint angles of the lower extremity and inertial sensor data such as accelerations and angular velocities were measured during a ski simulator exercise in order to evaluate the skill of skiers. Twenty experts and twenty unskilled skiers were recruited for the study. All expert skiers held the certificates issued by the Korea Ski Instructors Association. A three-dimensional motion capture system and two inertial sensors were used to acquire joint movements, heel acceleration and heel angular velocity during ski simulator exercises. Pattern variation values were calculated to assess the variations in ski simulator motion of expert and unskilled skiers. Integral ratio of roll angular velocity was calculated to determine the parallel alignment of the two feet. Results showed that ski experts showed greater range of motion of joint angle, peak-to-peak amplitude(PPA) of heel acceleration and PPA of heel angular velocity than unskilled skiers. Ski experts showed smaller pattern variations than unskilled skiers. In addition, the integral ratio of roll angular velocity in ski experts was closer to 1. Inertial sensor data measurements during the ski simulator exercises could be useful to evaluate the skill of the skier.

• 항공우주시스템공학회지
• /
• 제17권5호
• /
• pp.63-75
• /
• 2023

수송드론의 탑재안테나를 전파간섭성이 적게 예상되고 장착 가능한 5곳에 배치하여 안테나 방사 패턴을 시뮬레이션 하였다. 장착 위치에 따라 링크 마진이 0 dB 이하인 확률은 5.41%- 26.92%로 나타났다. 안테나 2개를 배치하고 1개를 선택하는 경우에는 링크 마진이 0 dB 이하인 확률은 0.11%-3.3%로 나타났다. 그 중에서 안테나를 전방과 후방에 장착하고, 1개는 상부에 나머지 1개는 하부에 배치하는 경우가 유리하였으며, 그 중에서도 안테나 1개는 전방 상부에 1개는 후방 하부에 배치하면 링크 두절 확률이 가장 낮은 것으로 나타났다. 이 경우에 비행체의 자세 roll, pitch를 제한하면 운용 거리 12 km 이하에서는 링크 두절이 발생하지 않을 것으로 분석되었다. 이 경우에 대해서 안테나 선택 수식을 도출하였으며, 또한 안테나의 빈번한 교번을 방지하기 위해서 히스테리시스 개념을 적용하여 수송드론의 가시선 데이터링크를 안정적으로 유지할 수 있도록 하고자 하였다.

• 한국정밀공학회지
• /
• 제31권11호
• /
• pp.993-998
• /
• 2014

Silver (Ag) grid patterned PET substrates were manufactured by thermal roll-imprinting methods. We coated highly conductive layer (HCL) as a supply electrode on the Ag grid patterned PET in the three kinds of conditions. One was no-HCL without conductive PEDOT:PSS on the Ag grid patterned PET substrate, another was thin-HCL coated with ~50 nm thickness of conductive PEDOT:PSS on the Ag grid PET, and the other was thick-HCL coated with ~95 nm thickness of conductive PEDOT:PSS. These three HCLs in order showed 73.8%, 71.9%, and 64.7% each in transmittance, while indicating $3.84{\Omega}/{\Box}$, $3.29{\Omega}/{\Box}$, and $2.65{\Omega}/{\Box}$ each in sheet resistance. Fabrication of organic solar cells (OSCs) with HCL Ag grid patterned PET substrates showed high power conversion efficiency (PCE) on the thin-HCL device. The thick-HCL device decreased efficiency due to low open circuit voltage ($V_{OC}$). And the Ag grid pattern device without HCL had the lowest energy efficiency caused by quite low short current density ($J_{SC}$).

• 대한치과교정학회지
• /
• 제45권4호
• /
• pp.153-163
• /
• 2015

Objective: The purpose of this study was to assess rotational patterns of dentofacial structures according to different vertical skeletal patterns by cone-beam computed tomography (CBCT) and analyze their influence on menton deviation in skeletal Class III deformity with mandibular asymmetry. Methods: The control group consisted of 30 young adults (15 men, 15 women) without any severe skeletal deformity. The asymmetry group included 55 adults (28 men, 27 women) with skeletal Class III deformity and at least 3-mm menton deviation from the midsagittal plane; it was divided into the hyperdivergent and hypodivergent subgroups using a mandibular plane angle cutoff of $35^{\circ}$. Fourteen rotational variables of the dental arches and mandible were measured and compared among the groups. Correlations between menton deviation and the other variables were evaluated. Results: The asymmetry group showed significantly larger measurements of roll and yaw in the mandible than the control group. The hypodivergent subgroup showed significant differences in maxillary posterior measurements of yaw (p < 0.01) and maxillary anterior shift (p < 0.05) compared with the hyperdivergent subgroup. All the mandibular measurements had significant correlations with menton deviation (p < 0.01). Most measurements of roll were positively correlated with one another (p < 0.01). Measurements of yaw and roll in the posterior regions were also positively correlated (p < 0.05). Conclusions: Menton deviation in skeletal Class III deformity with mandibular asymmetry is influenced by rotation of mandibular posterior dentofacial structures. The rotational patterns vary slightly according to the vertical skeletal pattern.

• 대한기계학회논문집B
• /
• 제25권10호
• /
• pp.1392-1399
• /
• 2001

The flow fields inside a molten Zn pot of continuous hot-chip galvanizing process were investigated experimentally. With varying several parameters including the strip speed Vs, flow rate Q of induction heater. scrapper location and baffle configuration, instantaneous velocity fields were measured using a PIV velocity field measurement technique. Inside the strip region, counter-clockwise rotating flow is dominant. The general flow pattern inside the strip region is nearly not influenced by the strip speed Vs, flow rate Q and the scrapper location. In the exit region, the flow separated from the moving strip due to the existence of a stabilizing roll ascends to the free surface, for the cases of no scrapper and scrapper detached form the roll. On the other hand, the ascending flow to the free surface is decreased, as the flow rate Q of induction heater increases. By installing a baffle around the uprising strip, the flow moving up to the stabilizing roll decreases. In addition, B-type baffle is better than A-type baffle in reducing speed of flow around the stabilizing rolls. However, the flow ascended to the free surface is largely influenced by changing the flow rate Q, and the scrapper location, irrespective of the baffle type.

• Advances in nano research
• /
• 제13권2호
• /
• pp.199-206
• /
• 2022

We present the high-brightness large-area 10.1" in-cell polarizer display panel integrated with a wire grid polarizer (WGP) and metal reflector, from the initial design to final system development in a commercially feasible level. We have modeled and developed the WGP architecture integrated with the metal reflector in a single in-cell layer, to achieve excellent polarization efficiency as well as brightness enhancement through the light recycling effect. After the optimization of key experimental parameters via Taguchi method, the roll nanoimprint lithography employing a flexible large-area tiled mold has been utilized to create the 90 nm-pitch polymer resist pattern with the 54.1 nm linewidth and 5.1 nm residual layer thickness. The 90 nm-pitch Al gratings with the 51.4 nm linewidth and 2150 Å height have been successfully fabricated after subsequent etch process, providing the in-cell WGPs with high optical performance in the entire visible light regime. Finally we have integrated the WGP in a commercial 10.1" display device and demonstrated its actual operation, exhibiting 1.24 times enhancement of brightness compared to a conventional film polarizer-based one, with the contrast ratio of 1,004:1. Polarization efficiency and transmittance of the developed WGPs in an in-cell polarizer panel achieve 99.995 % and 42.3 %, respectively.

• 융복합기술연구소 논문집
• /
• 제10권1호
• /
• pp.1-5
• /
• 2020

The wake shapes behind wings in formation flight are very important to the aerodynamics and performances of aircrafts. In the present study, a discrete vortex methood is extended to handle the wake rollups behind multiple wings. It was found that the relative distance between the wings and the rotational direction of the wingtip vortices have significant effect on the movement of the wingtip vortices. When the wings are close to each other, the wingtip vortices moved faster than the wings of large relative distances. The vortex pair of opposite signs generated from each wingtip has an effect of moving the wingtip vortices upward. The relative height between the wings has an effect of moving the wingtips along the centerline of each vortex. The wakeshape behind multiple wings is a function of the relative distances and thus is dependent on the configuration of the formation flight. In the futhre, a study on the vortex movement pattern will be studied.

• 한국가구학회지
• /
• 제28권4호
• /
• pp.259-267
• /
• 2017

Furniture should change according to space. Therefore, it is important that the flexibility of the furniture, the functional efficiency, the economical efficiency and the convenience of the furniture of today. These characteristics are also important for seminar tables that are used temporarily by a large number of people. The seminar furniture currently in use has no shielding plate, there are two forms of table and shielding plate folding table. Therefore, in this research, furniture design and product development that can complement the shortcomings of the seminar furniture currently in use were done. Analysis of problems through overseas investigation and domestic market research, design planning and design, and prototyping. We have sought to optimize the volume by applying the characteristics of RTA furniture to develop a lightweight, lightweight, lightweight, easy to install and easy to use shielding plate, and open and closed system. Basically developed two types of shielding board seminar table basic shape and Roll Screen type, we expanded the scope of application such as each color and pattern. In order to reduce the weight, we replaced the parts such as anchor bolts and hinges and the shielding plate with Roll Screen and pursued volume optimization. As a result of this research, it is expected that the system of mechanisms such as packaging standardization and damage prevention for weight reduction and volume optimization will contribute to building competitiveness by domestic office prefabricated furniture industry's original technology.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.36-42
• /
• 2015

TMixed convective flow in a bottom heated and top cooled rectangular channel can be significantly affected by the channel aspect ratio, Prandtl number, Reynolds number, Rayleigh number and angle of inclination. In such a mixed convection, the flow pattern plays an important role in various technological processes. In this study, a numerical investigation is carried out to explore mixed convection in a three-dimensional rectangular channel with bottom heated and top cooled uniformly. The three-dimensional governing equations are discretized using the finite volume method. In the range of low Reynolds number($0{\leq}Re{\leq}9.6{\times}10^{-2}$), the effects of the aspect ratio($2{\leq}AR{\leq}12$) and Gr/Re are presented and discussed. The longitudinal roll number in the channel is increased with increasing aspect ratio, and the roll number induced, regardless of the aspect ratio number, is even in the range of aspect ratios between 2 and 12, New vortex flow structure containing inclined longitudinal rolls is found, which is affected by aspect ratio and Reynolds number. The ratio Gr/Re is used to check the relative magnitudes of forced and natural convection in the mixed convective flow of high viscous fluid.