• Journal of the Optical Society of Korea
• /
• v.13 no.4
• /
• pp.416-422
• /
• 2009

We have demonstrated a highly efficient cladding-pumped ytterbium-doped fiber laser, generating $>$2.1 kW of continuous-wave output power at 1.1 μm with 74% slope efficiency with respect to launched pump power. The beam quality factor ($M^2$) was better than 1.2. The maximum output power was only limited by available pump power, showing no evidence of roll-over even at the highest output power. We present data on how the beam quality depends on the fiber parameter, based on our current and past fiber laser developments. We also discuss the ultimate power-capability of our fiber in terms of thermal management, Raman nonlinear scattering, and material damage, and estimate it to 10 kW.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.445-446
• /
• 2007

The use of plastic substrates enables new applications, such as flexible display devices, and other flexible electronic devices, using low cost, rollto-roll (R2R) fabrication technologies. One of the limitations of polymeric substrate in these applications is that oxygen and moisture rapidly diffuse through the material and subsequently degrade the electro-optical devices. GE Global Research (GEGR) has developed a plastic substrate technology comprised of a superior high-heat polycarbonate (LEXAN(R)) substrate film and a unique transparent coating package that provides the ultrahigh barrier (UHB) to moisture and oxygen, chemical resistance to solvents used in device fabrications, and a high performance transparent conductor. This article describes the coating solutions for polycarbonate (LEXAN(R)) films and its compatibility with OLED device fabrication processes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.2
• /
• pp.133-142
• /
• 2004

In this article, the constitutive relations of three types of piezoelectric benders, which are a unimorph bender, a bimorph bender and a triple-layer bender, are derived based on the beam theory under the quasi-static equilibrium condition. The relation coefficients are described as the geometry and material properties of the benders. More general constitutive relations involving fixed-free, fixed-roll, and fixed-simply supported boundary conditions under the inconsistent length condition between the piezoelectric layer and the nonpiezoelectric one are discussed. The complicated constitutive relations can be easily calculated and checked by using the symbolic function in ‘Mathematica’. The relation coefficients for the benders are plotted in three dimensional graph using the developed program.

• Journal of ILASS-Korea
• /
• v.10 no.4
• /
• pp.26-31
• /
• 2005

Today, the research to examine a fact that interaction between the air and the fluid free surface affects the steady state flow and air. We proved the interaction between vortex pairs and free surface on each condition that is created by the end of delta wings. Another purpose of this study is to investigate the effect of surface active material which call change the surface tension and we must consider when we refer to turbulent flow on surface tension. Therefore, this research examined the growth process of vortex pairs on condition of clean, contaminated free surface and wall after we made vortex pairs through counter rotating flaps. The results of this study suggest that vortex pairs in clean free surface rise safely but the vortex pairs in contaminated free surface and rigid, no slip is made secondary vortex or rebounding. However the secondary vortex in rigid, no slip is stronger than before. and we can find the vortex shape which roll up more completely. However, these will disappear by the effect of wall.

• Steel and Composite Structures
• /
• v.12 no.6
• /
• pp.465-489
• /
• 2012

Residual stresses play important role for design of steel structural members. Cold formed sections usually have residual stresses caused by roll forming. When compared to stresses caused by the working load, especially for compressed members, the effects of residual stresses can be favorable or unfavorable depending on magnitude, orientation and distribution of these stresses. The research presented in this paper includes experimental investigations of residual stresses, initial imperfections and material properties on cold formed carbon steel open cross sections. Experimental results have been compared to results obtained in similar tests with stainless and high strength steel cross sections. Theoretical and experimental research, conducted for cold formed open cross sections, are important for design of axially compressed members. This paper presents two methods of residual stresses investigation: magnetic method and method of pre-drilled holes and obtained results have been compared with results of residual stresses from other authors.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.4
• /
• pp.55-59
• /
• 2005

This paper presents a feasibility study whether Shida's constitutive equation being widely used for plain carbon steel in steel manufacturing industry can be extended to alloy steels with a due carbon equivalent model. T,he constitutive relation of the alloy steels (SAE9254, AISI52100 and AISI4140) is measured using hot deformation simulator (GLEEBLE 3500C) at high temperatures ($800^{\circ}C{\~}1000^{\circ}C$) within strain rates of $0.05{\~}40\;s^{-1}$. It has been found the predicted flow stress behavior (constitutive relation) of AISI52100 steel is in agreement with the measured one. On the other hand, the measured flow stress behavior of SAE9254 and AISI4140 steel partly concords with the predicted one when material experiences relatively high strain rate ($10{\~}40\;s^{-1}$) deformation at low temperature ($800^{\circ}C$). It can be deduced that, for AISI52100 steel, Shida's equation with the carbon equivalent model can be applicable directly to the roughing and intermediate finishing stand in hot rolling process for calculating the roll force and torque.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.33-42
• /
• 2004

Making use of SN steel in the building structure should be a prerequisite to adopt the design strength of said steel. As a preceding study, the material properties of STKN400B/490B tubes and SPAP235/325 and SPAR295 square pipes manufactured using SN400B/490B plates were evaluated. Compared with the yield and ultimate strengths of SN400B/490B plates, those of STKN400B/490B tubes increase. Nonetheless, the yield and ultimate strengths of STKN400B/490B tubes satisfied the design codes of STKN400B/490B tubes even though the tubes were fabricated via roll bending or press forming. On the other hand, the yield and ultimate strengths at the edges of SPAP235/325 square pipes did not satisfy the design codes based on the values at the sides. The maximum tensile and compressive residual stresses at the SN490B tube were equal to and 40% of the yield strength of the SN490B plate, respectively, In the case of the SPAP325 square pipe, both the maximum tensile and compressive residual stresses were 80% of the yield strength of the SN490B plate. The axial compressive loaded column test results snowed that the buckling strengths were not very different regardless of the mode of fabrication of STKN490B tunes. i.e., through roll bending or press forming. On the other hand, the buckling strength of the SPAP325 square pipe was higher than that of the built-up square pipe.

• Journal of the Korean Society for Railway
• /
• v.14 no.4
• /
• pp.313-319
• /
• 2011

In a modern society, various type of transportation modes are utilized, among them the subway system is the one of the main transportation mode which more than 7.21 million people ride a day in Seoul. Due to the increased interests on the indoor air quality (IAQ) of underground facilities, public concerns on IAQ of subway system are increasing also. Platform screen door (PSD) recently installed at the whole stations of Seoul subway and tunnel washing-out appeared to be effective in reducing particulate matters in the platform and tunnel. However there has not been any attempt to improve IAQ of subway cabin inside. Most technologies for removing airborne particulate matters are known to be difficult to adopt on the subway cabin due to the problem of maintenance cost. Therefore, the object of this study is a practical development of cabin air cleaning system which can reduce the concentration of airborne particles and harmful gases at the same time. In this paper, we focused on the development of particle removing system utilizing a roll-filter for increasing operating time of air filter. The prototype of system was designed and manufactured based on the numerical prediction results. For rollfilter device, 5 candidate filter materials were tested in point of particle collection efficiency and pressure drop. It was found that the electrically charged filter material showed the highest performance among them.

• Journal of Forest and Environmental Science
• /
• v.37 no.1
• /
• pp.52-61
• /
• 2021

Decay fungi can decompose plant debris to recycle carbon in the ecosystem. Still, they can also be fungal pathogens, which can damage living trees and/or wood material and cause a large amount of timber loss. We isolated and identified basidiomycetous fungi from the decayed bark of Mongolian oak wrapped with sticky roll traps. The degrading enzyme activities were then tested for all fungal isolates. The decay ability of selected isolates was assessed based on the weight loss of wood discs after inoculating with culture suspension of decay fungi under the different humidity levels. A total of 46 basidiomycetous fungal isolates belonged to 12 species, and 10 genera were obtained from Jong Myo (16 isolates), Chang Kyung palace (7 isolates), Cheong Gye (10 isolates), and Gun Po (13 isolates). Gymnopus luxurians was the most dominant fungus in the present study, and this species distributed in all survey sites with 9 isolates in Jong Myo, followed by 3 isolates in Chang Kyung palace, while Cheong Gye and Gun Po had only 1 isolate each. Among 46 isolates, 44 isolates secreted at least one enzyme, while 25 isolates produced both cellulase and phenol oxidase enzymes, and 2 isolates produced neither. The assessment of decay ability by artificial inoculation indicated that the weight loss of wood discs was significantly influenced by humidity conditions when inoculated with bark decay fungi. The percent weight losses by G. luxurians inoculation in RH of 90-100% and RH of 65-75% were 4.61% and 2.45%, respectively. The weight loss caused by Abortiporus biennis were 6.67% and 0.46% in RH of 90-100% and RH of 45-55%, respectively. The humidity reduction approach should be applied for further studies to control the growth and spread of bark decay fungi on the trunks wrapped with sticky roll traps.

• Journal of the Korean Electrochemical Society
• /
• v.24 no.2
• /
• pp.28-33
• /
• 2021

Many researchers have increased the loading level of electrodes to improve the energy density of secondary batteries. In this study, high-loading NCM523 (LiNi_0.5Co_0.2Mn_0.3O₂) positive electrode is manufactured using a polytetrafluoroethylene (PTFE) binder, not the conventional polyvinylidene fluoride (PVdF) binder, which has been commonly used in lithium-ion batteries. Through the kneading process using PTFE suspension, not the conventional slurry process using PVdF solution in N-methyl-2-pyrrolidinone (NMP), thick electrodes with high loading are easily manufactured. When the PTFE and PVdF-based electrodes are prepared at a loading level of 5.0 mAh/cm², respectively, the PTFE-based electrode shows better cycle performance and rate capability than those of PVdF-based electrodes. The electrode manufactured by the kneading process using a PTFE binder has high electrode porosity due to insufficient roll-press, but the porosity can be lowered by high temperature roll-press over 120℃. However, there is no significant difference in cycle performance according to the roll press temperature. In addition, the cycle performance of the high loading electrode is slightly improved by increasing the content of the conductive material. Overall, the PTFE binder can improve the performance of the high loading electrode, but additional solutions will be needed.