• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.55-60
• /
• 2011

For the bolster type bogie, bolster anchor body connections are proviede to transmit the longitudinal loads for traction or braking between the carbody and the truck. The bolster anchor body connection is generally composed of anchor rod bracket, anchor rod and its fastening devices. The bolster anchor body connection shall be basically capable of withstanding a longitudinal load resulting from excessive braking case or impact. Additionally the north America standard requires that the anchor rod bracket shall be frangible, I.e. the anchor rod bracket shall fail and fall away under load before the carbody structure is damaged since to protect the cabody structure in the event of unexpected accident. This paper describes the shear connection design using the optimized mechanical fasteners in the bolster anchor body connection to satisfy these Northe America requirements.

• Steel and Composite Structures
• /
• 제48권3호
• /
• pp.321-333
• /
• 2023

This paper proposes a comprehensive investigation on lateral stiffness of corner-supported steel modular frame using splice connection. A full-scale modular frame with two stacked steel modules under lateral load is tested. Ductile pattern in the transfer of lateral load is found in the final failure mode. Two types of lateral stiffness, including tangent stiffness and secant stiffness, are defined from the load-displacement due to the observed nonlinearity. The difference between these two types of stiffness is found around 20%. The comparisons between the experimental lateral stiffness and the predictions of classical methods are also conducted. The D-value method using hypothesis of independent case is a conservative option for predicting lateral stiffness, which is more recommended than method of contraflexural bending moment. Analyses on two classical short-rod models, including fix-rod model and pin-rod model, are further conducted. Results indicate that fix-rod model is more recommended than pin-rod model to simplify splice connection for simulation on lateral stiffness of modular frame in elastic design stage.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.85-88
• /
• 2004

In this study, a simple moment-resisting precast concrete beam-column connection is proposed for highly seismic zone using dywidag ductile rod [DDC]. DDC is superior system for ductility, energy dissipation capacity, connection strength, and drift capacity. A study was carried out to investigate the connection behavior subjected to cyclic inelastic loading. Four Precast beam-column interior connections and one monolithic connection will be tested. The variables will be examined were the strength relationship between joint's ductile rod and beam reinforcement for gain energy dissipation capacity. The specimens will be tested only reverse cyclic loading in accordance with a prescribed displacement history. Connection performance is evaluated on the basis of ductility, energy dissipation capacity, connection strength, and drift capacity. the precast connection using DDC is capable of matching of exceeding the performance of the monolithic connection and thereby provides moment-resisting behavior.

• Steel and Composite Structures
• /
• 제32권4호
• /
• pp.497-507
• /
• 2019

Exposed column base connections are used in low- to mid-rise steel moment resisting frames. This paper is to investigate the effect of the base plate thickness on the exposed column base connection strength, stiffness, and energy dissipation. Five specimens with different base plate thickness were numerically modelled using ABAQUS software. The numerical model is able to reproduce the key characteristics of the experimental response. Based on the numerical analysis, the critical base plate thickness to identify the base plate and anchor rod yield mechanism is proposed. For the connection with base plate yield mechanism, the resisting moment is carried by the flexural bending of the base plate. Yield lines in the base plate on the tension side and compression side are illustrated, respectively. This type of connection exhibits a relatively large energy dissipation. For the connection with anchor rod yield mechanism, the moment is resisted through a combination of bearing stresses of concrete foundation on the compression side and tensile forces in the anchor rods on the tension side. This type of connection exhibits self-centering behavior and shows higher initial stiffness and bending strength. In addition, the methods to predict the moment resistance of the connection with different yield mechanisms are presented. And the evaluated moment resistances agree well with the values obtained from the FEM model.

• 한국산업융합학회 논문집
• /
• 제9권4호
• /
• pp.309-315
• /
• 2006

Important material properties of UCAS rod can divide by tension characteristic of base rod part and both end part of U type anchor. Tensile properties of base rod part need as concrete reinforcement material as an alternative material of reinforcing rod, and tensile properties of U type anchor is used at connection with UCAS rod. This treatise carry out tensile test of UCAS rod, examine necessary properties such as strength, elastic modulus and maximum capacity of UCAS rod as reinforcement material of concrete. Also, to examine material properties carry out tensile test of U type anchor.

• 한국건축시공학회지
• /
• 제22권2호
• /
• pp.149-160
• /
• 2022

본 연구에서는 국내에서 생산되는 목재와 접착제를 활용한 Glued-in rod 접합부의 인발성능을 평가하고자 접착제의 종류, 철근의 매입깊이 및 매입방향을 고려한 인발성능 실험연구를 수행하였다. 실험결과, 액상형 접착제 사용 실험체가 더 우수한 인발성능을 보여주었으며, 철근의 매입깊이가 길어질수록 철근의 항복을 먼저 유도하여 높은 최대 인발하중을 보여주었다. 인발성능 실험결과를 통하여 철근의 항복강도보다 접착제의 부착강도를 더 강하게 설계하는 것이 유리한 Glued-in rod 접합부 설계식을 제안하였으며, 접착제의 부착강도의 시공오차를 고려한 보정계수 0.75 또한 제안하였다.

• Environmental Engineering Research
• /
• 제25권2호
• /
• pp.238-242
• /
• 2020

Sediment microbial fuel cells (SMFCs) illustrated great potential for powering environmental sensors and bioremediation of sediments. In the present study, array anodes for SMFCs were fabricated with graphite rods as anode material and stainless steel plate as electric current collector to make it inconvenient to in situ settle down and not feasible for large-scale application. The results demonstrated that maximum power of 89.4 ㎼ was obtained from three graphite rods, twice of 43.3 ㎼ for two graphite rods. Electrochemical impedance spectroscopy revealed that three graphite rods resulted in anodic resistance of 61.2 Ω, relative to 76.0 Ω of two graphite rods. It was probably caused by the parallel connection of the graphite rods, as well as more biomass which could reduce the charge transfer resistance of the biofilm anode. The presently designed array configuration possesses the advantages of easy to enlarge the surface area, decrease in anodic resistance because of the parallel connection of each graphite rod, and convenience to berry into sediment by gravity. Therefore, the as prepared array node would be an effective method to fabricate large-scale SMFC and make it easy to in situ applicate in natural sediments.

• 한국지반공학회논문집
• /
• 제27권1호
• /
• pp.77-86
• /
• 2011

건설 프로젝트의 대형화와 시공장소의 다양화에 따라 지반 조사 내용이 다양해지고 있다. 더욱이 날로 엄격해지는 시공조건으로 인해 보다 높은 수준의 지반정보가 요구되고 있다. 그러나 우리나라에서는 최근까지도 비교적 결과의 신뢰도가 낮은 표준관입실험 등의 원위치 실험법에 의존하고 있는 현실이다. 본 논문에서는 복합적인 지반의 거동 특성 평가를 위하여 연약지반은 물론 암반에서도 에너지 변화를 측정할 수 있는 새로운 콘관입 실험기를 개발하고자 하였다. 본 연구에서는 롯드의 체결 방식에 따른 에너지 감쇠를 평가하기 위해 롯드를 인위적으로 불완전하게 체결하거나, 전체 길이는 일정하게 유지시키면서 체결된 롯드의 수를 변화시키며 실험을 수행하였다. 또한, 체결 조건이 다른 롯드에서 탄성파의 전달율과 반사율을 적용하여 에너지 손실을 평가 하였다. 그리고 정동적 콘관입 실험 장비를 제작하여 두부와 선단부에 변형률계와 가속도계를 부착함으로써 에너지 손실을 실내 실험을 통하여 평가하고자 하였다. 실험 결과 롯드의 체결 상태가 완벽하지 않으면 에너지 전달률이 급격히 감소하는 것을 실험과 시뮬레이션을 통하여 알 수 있었다. 또한 실내 실험결과 새로 개발된 정동적 콘 관입 실험기의 두부와 선단부의 전달에너지가 다름을 알 수 있었다. 본 연구에서는 두부는 물론 선단부에서의 에너지 평가가 필요함을 알 수 있었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 자동차부품 제작기술의 진보
• /
• pp.35-46
• /
• 1996

The powder forging process offers beneficial material utilization as well as the minimization of finishing operations over that of conventionally forged rods. In the present work, the sintering behavior of Fe-2Cu-0.6C-0.35MnS, optimum preform design and forgeability of various forging conditions were investigated. This data were generated using a newly proposed sub-scaled con-rod specimen developed specifically to simulate the powder forging process. The results of present work, powder perform is so difficult to flow material into die cavity and mass flow has no effect on improving the strength. And, applied force to increase density of the specimen flowed material is greater than that of all repessing mode. On the contrary, the specimen flowed material became increased hardness of inside in contrast with all repressing mode, but the tensile strength were decreased with residual porosity in surface. Due to material flow characteristic of powder preform, the section of lower density in powder preform became also lower density in forged con-rod. So, preform design is very important in manufacturing powder forged connecting rod.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1995년도 추계학술발표회논문집(2)
• /
• pp.680-686
• /
• 1995

It has been known that water-side corrosion of fuel rods in nuclear reactor is accompanied with the loss of metallic wall thickness and pickup of hydrogen. This corrosion is one of the important limiting factors ill the operating life of fuel rods. In connection with the fuel cladding corrosion, a device to measure the water-side oxide layer thickness by means of the eddy-current method without destructing the fuel rod was developed by KAERI. The device was installed on the multi-function testing bench in the nondestructive test hot-cell and its calibration was carried out successfully for the standard rod attached with plastic thin films whose thicknesses are predetermined. It shows good precision within about 10% error. And a PWR fuel rod, one of the J-44 assembly discharged from Kori nuclear power plant Unit-2, has been selected for oxide layer thickness measurements. With the result of data analysis, it appeared that the oxide layer thicknesses of Zircaloy cladding vary with the length of the fuel rod, and their thicknesses were compared with those of the destructive test results to confirm the real thicknesses.