• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.163-171
• /
• 1999

The abnormal grain coarsening in wire rolling induces detrimental defects, such as jagged size tolorance, severe bending after heat treatments and drawing troubles, in the following secondary processes. Neishi et al observed that there is a band type region where grain coarsenting occurs in the plastic strain vs. deformation temperature plot. Based on the finding, we have investigate whether grain sizes and ferrite volume fractions are correlation to deformation strain with three kinds of wire rod diameters as for the different average deformation conditions. The samples were chosen from the No.2 Wire Rod Mill of POSCO where 3-roll type of finishing mill stand are used. It was found in the present work that the grain size and ferrite volume fraction of the rolled and cooled microstructure were changed with rolling reduction and rolling temperature. Abnormally grown grains at various observed points were also found. To have homogeneously fine grains of microstructure from the No. 2 Wire Rod Mill, it will be easier to control finish rolling temperature at around 750$^{\circ}C$ rather than to find another rolling schedule.

• International Journal of Precision Engineering and Manufacturing
• /
• v.8 no.1
• /
• pp.27-31
• /
• 2007

A rolling speed dependent spread model is proposed for predicting the exit cross sectional shape in oval-round (or round-oval) pass rod rolling process when the rolling speed is very high. The effect of rolling speed on the exit cross sectional shape is measured by performing a four-pass continuous high speed (${\sim}80m/s$) rod rolling test and is described in terms of the spread correction parameter. The validity of the model is examined by applying it to rod rolling process at POSCO No.3 Rod Mill. The cross sectional shapes of workpiece predicted by the proposed model coupled with the surface profile prediction $method^{6}$ are in good agreement with those obtained experimentally.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.180-187
• /
• 1999

This document illustrates the relationship between the wire rod wrinkle defect and the roll caliber design. The wrinkle defect is caused by the incongruent rolling conditions of the roll caliber design, the roll adjustment, and the extracting temperature. In this document, we restrict the study scope to the roll caliber design's effect on wrinkle defect at the base of real condition of the No.2 Wire Rod mill, POSCO. There has been wrinkle defect problem in the No.2 Wire Rod Mill, POSCO for many years. The engineers of the wire rod mill have been making efforts to solve the problem. As one of the efforts, we take the samples of the wire rod in the each stands of the 2'nd wire rod mill and then analyze the samples. Through the analysis, we find out the problem of the roll caliber design. So, we suggest the roll caliber design method to be more effective to weaken the wrinkle defect.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.38-45
• /
• 2017

A finite element analysis-based approach which investigates the causes of the breakdown in the outer ring of the choke at hot rod rolling mill is presented. Two-dimensional drawings of the whole vertical-type mill stand are transformed into three-dimensional CAD models. Non-linear elasto-plastic deformation analysis of material at the roll gap is performed for computing roll force and torque of the work roll. Then, the reaction forces of the bearing rings together with a set of roller bearings that support the work roll are obtained by means of rigid body motion analysis. Finally, stress behaviors in the bearing rings together with a set of roller bearings that support the work roll are investigated by linear elastic analysis. Results reveal that stress at the contact area between the outer ring and roller bearing is extraordinary high when an internal gap between an external surface of the outer ring and the internal surface of the chock due to wear of the inside of the chock occurs.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.27-36
• /
• 2004

Contemporary objectives for steel rod rolling processing are increasingly complex and often contrasting i.e. obtaining a desired product with optimum combination of properties such as strength, toughness and formability at lower cost. Low-alloy steel rods have been produced with several heat treatments for drawing and forging processes at room temperature. In order to reduce these heat treatments much of the researches concerning of high temperature mechanical behavior of steel rods have been conducted at wire rod mill of POSCO. In this present work, optimizations of rolling temperature and cooling rate for JS-SCM435 are performed to eliminate softening heat treatment(Low Temperature Annealing) for drawing process. The results from the optimization changed the microstructure of rods after rod rolling from Bainite with high tensile strength of 1000Mpa to Pearlite and Ferrite with appropriate strength of 750Mpa that is equivalent tensile strength after softening heat treatment.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2516-2518
• /
• 2000

In order to reduce the trimming loss for water cooling zone next to finishing block mill in wire rolling, the operational data related to the crop length control of uncooled region was acquired and analyzed. The time deviation of water cooling spray nozzles and the immoderate preset length of uncooled wire rod result in the excessive trimming loss. Therefore, the preset length of uncooled wire rod at each cooling zone are established. The test results of #3 wire rolling mill turned out to be good enough to be expected to increase the ratio of products about 0.15% and establish operational standards of cooling zone.

• Transactions of Materials Processing
• /
• v.17 no.1
• /
• pp.68-72
• /
• 2008

In order to investigate the evolution of strain states during screw rolling, the samples of copper rod were rolled in a three-roll screw rolling mill. Microstructure observations and hardness measurements were carried out for examining the deformation history during screw rolling. The finite element method(FEM) was employed to calculate the evolution of strain states during screw rolling. The strain state in the roll gap is quite inhomogeneous through the rod thickness layers. It turned out that shear strain gradients through the thickness layers are reduced by applying a higher reduction.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.158-161
• /
• 2007

In order to investigate the evolution of strain states during screw rolling, the samples of pure copper rod were rolled in a three-roll screw rolling mill. Microstructure observations and hardness measurements were carried out for examining the deformation during screw rolling. In addition, the finite element method (FEM) was employed to calculate. The strain states reveal that the shear strain plays a dominant role in the deformation during screw rolling.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.333-336
• /
• 2008

The groove rolling is a process that transforms the bloom or billet into a shape with circular section through a series of rolling. Inhibition of surface defect generation in groove rolling is a matter of great importance and therefore many research groups proposed a lot of models to find the location of surface defect initiation. In this study, we propose a model for maximum shear stress ratio over equivalent strain to catch the location of surface defect onset. This model is coupled with element removing method and applied to box groove rolling of POSCO No. 3 Rod Mill. Results show that proposed model in this study can find the location of surface defect initiation during groove rolling when finite element analysis results is compared with experiments. The proposed criterion has been applied successfully to design roll grooves which inhibits the generation of surface defect.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.607-612
• /
• 2008

The groove rolling is a process that transforms the bloom or billet into a shape with circular section through a series of rolling. Inhibition of surface defect generation in groove rolling is a matter of great importance and therefore many research groups proposed a lot of models to find the location of surface defect initiation. In this study, we propose a model for maximum shear stress ratio over equivalent strain to catch the location of surface defect onset. This model is coupled with element removing method and applied to box groove rolling of POSCO No.3 Rod Mill. Results show that proposed model in this study can find the location of surface defect initiation during groove rolling when finite element analysis results is compared with experiments. The proposed criterion has been applied successfully to design roll grooves which inhibit the generation of surface defect.