• Geomechanics and Engineering
• /
• v.18 no.4
• /
• pp.363-371
• /
• 2019

In this study, the load carrying behavior of piled rafts installed in inclined bearing rock layer was investigated for rock-mounted and -socketed conditions. It was found that settlements induced for an inclined bearing rock layer are larger than for a horizontal layer condition. The load capacity of piled rafts for the rock-mounted condition decreased as rock-layer inclination angle (${\theta}$) increased, while vice versa for the rock-socketed condition. The load capacities of raft and piles both decreased with increasing ${\theta}$ for the rock-mounted condition. When bearing rock layer was inclined, loads carried by uphill-side piles were greater than those by downhill-side piles. The values of differential settlements of rock-mounted and -socketed conditions were not significantly different whereas slightly higher for the rock-socketed condition. The values of load sharing ratio (${\alpha}_p$) and its variation with settlement were not markedly changed by the inclination of bedrock. It was shown that ${\alpha}_p$ for piled rafts installed in rock layer was not affected by ${\theta}$ whereas actual loads carried by raft and piles may vary depending on the pile installation and rock-layer inclination conditions.

• Tunnel and Underground Space
• /
• v.7 no.2
• /
• pp.108-115
• /
• 1997

Uniaxial and biaxial compressive tests were conducted on limestone specimens containing artificial joints and a circular hole to investigate the influence of inclination and number of joints on compressive strength and deformation behavior of rock with a circular hole. Under uniaxial and biaxial compressive condition, the inclination of joints showing the maximum and minimum strength were 0$^{\circ}$ and 30$^{\circ}$ respectively, which was independent of the number of joints. Under uniaxial compressive condition, relative maximum strength of rock with n=1 and 3 to intact rock with a circular hole were 12.5%~82.8% and 11.4~62.5% respectively, and under biaxial compressive condition, 18.2~91.0% and 17.0~87.5% respectively. The influence of the number of joints on the decrease of compressive strength was greater under uniaxial than under biaxial compressive condition. Under uniaxial and biaxial compressive condition, axial and lateral deformations of rock showed the least values where $\alpha$=30$^{\circ}$. Under uniaxial compressive condition, axial and lateral deformation at maximum strength of rock have the increasing tendency with increase the number of joints. But they have the decreasing tendency under biaxial compressive condition. Under uniaxial and biaxial compressive conditions, axial deformation of circular hole was greater than lateral deformation without respect to the number of joints and the inclination of joints.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.2
• /
• pp.13-21
• /
• 2018

The magnitude and distribution of earth pressure on the excavation wall in jointed rock mass were examined by considering different wall permeability conditions as well as rock types and joint inclination angles. The study was numerically extended based on a physical model test (Son & Park, 2014), considering rock-structure interactions with the discrete element method, which can consider various characteristics of rock joints. This study focused on the effect of the permeability condition of excavation wall on the earth pressure in jointed rock masses under a groundwater condition, which is important but has not been studied previously. The study results showed that the earth pressure was highly influenced by wall permeability as well as rock type and joint condition. Earth pressure resulted from the study was also compared with Peck's earth pressure in soil ground, and the comparison clearly showed that the earth pressure in jointed rock mass can be greatly different from that in soil ground.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.967-973
• /
• 2004

Rock socketed drilled shafts transfer significant portion of structural loads at the socketed part. Therefore, a proper design of side and base resistances of a shaft at the socket is a major concern for the geotechnical engineers. In this study, we modified the Hoek-Brown criterion to estimate side resistance of rock socketed drilled shafts. Earlier method to compute side resistance of a shaft is linear or power functions of intact rock masses. However, side resistance is mobilized like shearing which influenced by the mechanical properties of concrete and rock masses, adhesion of rock/concrete interface, roughness of rock socket. Therefore, a single coefficient or power of uniaxial compressive strength of intact rock cannot provide accurate values of side resistance in a wide range of the uniaxial compressive strength. A new approach proposed in this study can consider in situ rock mass condition (frequency or discontinuities, weathering condition), and rock types thus, it has a wider applicability than the earlier models.

• Tunnel and Underground Space
• /
• v.24 no.3
• /
• pp.224-233
• /
• 2014

It is well known that rock properties can be affected by loading in underground condition. In the case of flooded underground mine or tunnels, rock properties variation due to loading might be different from the loading in dry condition. In order to verify the influence of saturated loading condition on rock properties, various laboratory tests had been carried out. Loading on the rock specimen was controlled to be ranged in between 20 ~ 80% of UCS. By comparing the variation of thermal, mechanical, and physical properties of rock specimens under the same load in saturated and dry condition, it was possible to find that the rock properties can be more significantly disturbed in the saturated loading condition than in dry loading condition.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.1
• /
• pp.29-37
• /
• 2016

This study examined the magnitude and distribution of earth pressure on the support system in a jointed rock mass due to the different joint spacing as well as varying the rock type and joint condition (joint shear strength and joint inclination angle). Based on a physical model test and its numerical simulation, a series of numerical parametric analyses were conducted using a discrete element method. The results showed that the magnitude and distribution of earth pressure were strongly affected by the different joint spacing as well as the rock type and joint condition. In addition, the study results were compared with Peck's earth pressure for soil ground, which indicated that the earth pressure in a jointed rock mass could be considerably different from that in soil ground. The study suggests that the joint spacing as well as the rock type and joint condition are important factors affecting the earth pressure in a jointed rock mass and they should be considered when designing a support system in a jointed rock mass.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.658-663
• /
• 2010

Recently the most of deep foundation were socketed into weathered rock or soft rock to carry large foundation loads. The end bearing behavior of piles socketed in rock is generally dependent on the rock mass conditions with discontinuities and rock strength. Therefore, it is very important that the estimating rock classification with relation of TCR, RQD and unpredicted rock condition. In this study, the construction failure example of drilled shaft due to mistaking to estimate the rock classification on penetration were analyzed in site, so we hope to discuss problems of determining the rock socketed length of drilled shaft on construction.

• Tunnel and Underground Space
• /
• v.15 no.5 s.58
• /
• pp.330-337
• /
• 2005

Apart from the geometric features of the rock joints, the shear characteristics of rock mass subject to shear force are also significantly affected by the boundary conditions in the neighborhood of the rock mass. The boundary conditions of the rock mass can be classified into 4 categories according to the stress state of the rock joint, of which the constant normal load (CNL) is the most used for shear test and produces the lowest shear strength and different behavior. In this study, the shear behavior under constant normal stiffness condition was able to replicated by the graphic method normalized by the test results under constant normal stress condition.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.265-272
• /
• 2003

In this study, the rock mass classification results from the face mapping and the resistivity inversion data are compared and analyzed for the reliability investigation of the determination of the rock support type based on the surface electrical survey. To get the quantitative correlation, rock engineering indices such as RCR(rock condition rating), N(Rock mass number), Q-system based on RMR(rock mass rating) are calculated. Kriging method as a post processing technique for global optimization is used to improve its resolution. The result of correlation analysis shows that the geological condition estimated from 2D electrical resistivity survey is coincident globally with the trend of rock type except for a few local areas. The correlation between the results of 3D electrical resistivity survey and the rock mass classification turns out to be very high. It can be concluded that 3D electrical resistivity survey is powerful to set up the reliable rock support type.

• Tunnel and Underground Space
• /
• v.7 no.2
• /
• pp.91-99
• /
• 1997

To stabilize the energy price, the more storage facilities of energy are required and among the storage methods of LPG and LNG, the method of storage at low temperature under normal confining pressure is considered. It is needed to understand the mechanical and thermal characteristics of rock under temperature variation so that the behaviors of rock can be predicted. In this paper, the variation of the rock charateristics of the Hwangdeung granite and the Boryung sandstone is studied at low temperature. The mechanical characteristics of rock under low temperatures are that as temperature decreased, unaxial compression strength and Young's modulus increased for Hwangdeung granite; strength and Young's modulus in wet condition were greater than those in dry condition. In the case of Boryung sandstone, as temperature decreases unaxial compression strength and Young's modulus increase but decrease below -10$0^{\circ}C$ in dry condition and below -16$0^{\circ}C$ in wet condtion. The mechanical characteristics of rock after cooling to previous temperature and thawing are that uniaxial compression strength and Young's modulus decrease as temperature decreases. Uniaxial compression strength and Young's modulus in wet conditon decrease more than those in dry condition. Brazilian tension strength decreases as temperature decreases.