• 터널과지하공간
• /
• 제4권3호
• /
• pp.215-227
• /
• 1994

Rock Mass classifications have been developed in many European countries. The most widely used classification methods are the Rock Mass Rating (RMR) system proposed by Bieniawski(1973) and the Q-system developed By Barton et al. (1974). These methods are also adopted at many mountain tunnels and subway sites in our country. Here, a geomechanical classification for slopeds in rock, the "Slope Mass Rating"(SMR) is presented for the preliminary assessment of slope stabiliyt. This method can be applied to excavation and support design in the front part of tunnel and cutting area as a guide line and recommendation on support methods which allow a systemmetic use of geomechanical classification for rock slopes.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.658-663
• /
• 2010

Recently the most of deep foundation were socketed into weathered rock or soft rock to carry large foundation loads. The end bearing behavior of piles socketed in rock is generally dependent on the rock mass conditions with discontinuities and rock strength. Therefore, it is very important that the estimating rock classification with relation of TCR, RQD and unpredicted rock condition. In this study, the construction failure example of drilled shaft due to mistaking to estimate the rock classification on penetration were analyzed in site, so we hope to discuss problems of determining the rock socketed length of drilled shaft on construction.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.265-272
• /
• 2003

In this study, the rock mass classification results from the face mapping and the resistivity inversion data are compared and analyzed for the reliability investigation of the determination of the rock support type based on the surface electrical survey. To get the quantitative correlation, rock engineering indices such as RCR(rock condition rating), N(Rock mass number), Q-system based on RMR(rock mass rating) are calculated. Kriging method as a post processing technique for global optimization is used to improve its resolution. The result of correlation analysis shows that the geological condition estimated from 2D electrical resistivity survey is coincident globally with the trend of rock type except for a few local areas. The correlation between the results of 3D electrical resistivity survey and the rock mass classification turns out to be very high. It can be concluded that 3D electrical resistivity survey is powerful to set up the reliable rock support type.

• 화약ㆍ발파
• /
• 제24권1호
• /
• pp.63-69
• /
• 2006

터널굴착이나 사면절취 등과 같은 굴착문제에 있어서 굴착방법을 결정하기 위해 대상암반에 대한 리핑 암이나 발파암의 구분이 우선되며, 다음에 발파에 의한 굴착방법이 선정되었을지라도 화약량 및 종류, 천공방법 등 발파설계를 위해서 추가적으로 발파암에 대한 세부적인 분류가 필요하다. 일반적으로 RMR 이나 Q 시스템과 같은 암반분류법이 많이 사용되고 있지만, 발파암에 대한 표준적인 암반분류법이 없으며, 국내에서도 발파암 분류에 대한 연구가 거의 전무한 상태로 발파암의 분류요소로 사용될 수 있는 요소를 구하기 위한 연구가 필요하다, 본 논문에서는 앞으로 국내에서 발파암 분류연구에 대한 방향제시를 위해서 발파와 암석의 역학적 특성, 지질구조와 불연속면의 특성과의 관계나 굴착과 관련된 암반분류에 대한 여러 논문사례를 통하여 발파암의 분류 요소와 분류방법 등을 분석한다.

• 터널과지하공간
• /
• 제6권3호
• /
• pp.197-208
• /
• 1996

Due to the constraints in pre site-investigation for tunnel, it is essential to redesign the support structures suitable for rock mass conditions such as rock strength, ground water and discontinuity conditions for safe tunnel construction. For the selection of optimum support, it is very important to carry out the rock mass classification and in-situ measurement in tunnelling. In this paper, in a mountain tunnel designed by NATM in hard rock, the selectable system for optimum support has been studied. The tunnel is situated at Chun-an in Kyungbu highspeed railway line with 2 lanes over a length of 4, 020 m and a diameter of 15 m. The tunnel was constructed by drill & blasting method and long bench cut method, designed five types of standard support patterns according to rock mass conditions. In this tunnel, face mapping based on image processing of tunnel face and rock mass classification by RMR carried out for the quantitative evaluation of the characteristics of rock mass and compared with rock mass classes in design. Also, in-situ measurement of convergence and crown settlement conducted about 30 m interval, assessed the stability of tunnel from the analysis of monitoring data. Through the results of rock mass classification and in-situ measurement in several sections, the design of supports were modified for the safe and economic tunnelling.

• Geomechanics and Engineering
• /
• 제30권5호
• /
• pp.449-460
• /
• 2022

Safe underground construction in a rock mass requires adequate ground investigation and effective determination of rock conditions. The estimation of rock mass behavior is difficult, because rock masses are innately anisotropic and heterogeneous at different scales and are affected by various environmental factors. Quantitative rock mass classification systems, such as the Q-system and rock mass rating, are widely used for characterization and engineering design. The measurement of rock classification parameters is subjective and can vary among observers, resulting in questionable accuracy. Geophysical investigation methods, such as seismic surveys, have also been used for ground characterization. Torsional shear wave propagation characteristics in cylindrical rods are equal to that in an infinite media. A probabilistic quantitative relationship between the Q-value and shear wave velocity is thus investigated considering long-wavelength wave propagation in equivalent continuum jointed rock masses. Individual Q-system parameters are correlated with stress-dependent shear wave velocities in jointed rocks using experimental and numerical methods. The relationship between the Q-value and the shear wave velocity is normalized using a defined reference condition. This relationship is further improved using probabilistic analysis to remove unrealistic data and to suggest a range of Q-values for a given wave velocity. The proposed probabilistic Q-value estimation is then compared with field measurements and cross-hole seismic test data to verify its applicability.

• 한국지반공학회논문집
• /
• 제24권11호
• /
• pp.43-53
• /
• 2008

현재 국내에서 사용되고 있는 암반분류법은 발주처인 각 기관별로 표준화되어 있지 않을 뿐만 아니라 그 기준값이 상이하여 각 단계별 참여기술자간에 암반 판정의 불일치가 야기될 수 있다. 따라서 본 연구에서는 국내에서 적용되고 있는 암반분류법의 문제점을 개선하기 위하여 국내 암반분류 기준들과 국제적 기준들을 비교, 검토하여 표준화된 분류요소를 제시하고, 각 요소에 대한 기준값을 합리적이며 객관적으로 정량화함으로써 이를 종합적으로 이용하는 평가 방식의 암반분류 안을 제시하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.999-1008
• /
• 2009

A series of sedimentary rocks which are formed in the Tertiary are distributed around Samcheok(Samcheok-Pukpyoung basin), Younghae(Younghae basin), Pohang(Pohang basin), Gyeongju(Yangnam basin), Ulsan(Ulsan basin), Jeju(Seogyuipo formation) in the southern region of the Korean Peninsula. This study concerned with geological, geophysical, geotechnical properties of the unconsolidated rocks in the Pohang area. A consolidated rocks are classified as hard rock - soft rock - weathered rock - residual soil follows in degree of weathering. But unconsolidated rocks has soil properties as well as rock's at the same time. The results of field excursion, boring, borehole-logging, rock testing, geophysical survey, laboratory test are soft rock range, but the durability of the rock until the residual soil from the weathered rock. We accomplished the rock mass classification of the unconsolidated rocks.

• 터널과지하공간
• /
• 제7권1호
• /
• pp.1-12
• /
• 1997

Engineering rock mass classification is extensively used to determine the reasonable support system throughout the tunneling process in the field. Selection of support system based on the results of engineering rock mass classification is simple and straight-forward. However, this method cannot consider the effect of in-situ stresses, mechanical properties of support material, and support installation time on the behavior or rock-support system To handle the various conditions encountered in the underground excavation sites rock-support system. To handle the various conditions encountered in th eunderground excavation sites rock-support interaction program has been developed. This program can analyze the interaction between rock mass and support materials and also can simulate the tunnel excavation-support insstallation process by controlling the support installation time and the stiffness of support system. Practical applicability of this program was verfied by comparing the results of support design to those from rock mass classification for virtual underground excavation at the drilling site KD-06 in Geoje island.

• 터널과지하공간
• /
• 제17권2호
• /
• pp.102-108
• /
• 2007

일반적으로 암판정을 수행하기 인해 가장 널리 사용되는 방법은 암석의 강도와 절리의 발달빈도를 고려하는 것이다. 하지만 미세균열과 연장성이 긴 절리들이 암반에 존재하고 있는 경우에는 이러한 방법이 합리적이지 않다. 그러므로 복잡한 지질조건을 가지고 있는 암반에서의 굴착난이도 결정은 절리빈도와 실내시험(일축압축강도, 점하중강도, 실내탄성파속도 등)과 현장탄성파속도와의 상관관계를 종합하여 암판정을 수행하는 것이 더욱 더 합리적이라고 판단된다.